Performance Evaluation of 14 nm FinFET-Based 6T SRAM Cell Functionality for DC and Transient Circuit Analysis

As the technology node size decreases, the number of static random-access memory (SRAM) cells on a single word line increases. The coupling capacitance will increase with the increase of the load of word line, which reduces the performance of SRAM, more obvious in the SRAM signal delay and the SRAM power usage. The main purpose of this study is to investigate the stability and evaluate the power consumption of a 14 nm gate length FinFET-based 6T SRAM cell functionality for direct current (DC) and transient circuit analysis, namely, in resistor-capacitor (RC) delay. In particular, Berkeley Short-channel IGFET Model-Common Multigate (BSIM-CMG) model is utilized. The simulation of the SRAM model is carried out in HSPICE based on 14 nm process technology. A shorted-gate (SG) mode FinFET is modeled on a silicon on insulator (SOI) substrate. It is tested in terms of functionality and stability. Then, a functional SRAM is simulated with 5 GHz square wave at the input of word line (WL). Ideal square wave and square wave with 100  RC, 5  RC, 1  RC, and 0.5  RC are asserted to the WL and the bit lines (BL&BLB) of SRAM. Voltage at node q and q- is observed. The simulation shows that 1 RC is the minimum square wave that will store correct value in node q and node q-. Thus, this discovery from the research can be used as a modeling platform for circuit designers to explore and improve the SRAM tolerance against RC delay

Low-Power And High Performance Of An Optimized FinFET Based 8T SRAM Cell Design

The development of the nanotechnology leadsto the shrinking of the size of the transistors to nanometerregion. However, there are a lot of challenges due to sizescaling of the transistors such as short channel effects (SCEs)and threshold voltage roll-off issues. Fin-Type Field EffectTransistor (FinFET) is another alternative technology tosolve the issues of the conventional MOSFET and increasethe performance of the Static Random Access Memory(SRAM) circuit design. FinFET based SRAMs are faster andmore reliable which are often used as memory cache for highspeed operation. However, 6T SRAM cell suffers from accesstransistor sizing conflict resulting in a trade-off between readand write stability. This paper presents an investigation ofthe stability performance in retention, read and write modeof 22nm FinFET based 8T SRAM cell. The performancecomparison of 22nm FinFET based 6T and 8T SRAMs weremade. The simulation of the SRAM model are carried out inGTS Framework TCAD tool based on 22nm technology. In8T SRAM cell, two n-FinFETs are added to the conventional6T SRAM cell which will be controlled by the Read WordLine (RWL) to isolate the read and write operation path forbetter read stability. FinFET based 8T SRAM cell givesbetter performance in Static Noise Margin (SNM) and powerconsumption than 6T SRAM cells. The simulation resultsaffirms the proposed FinFET based 8T SRAM improvedread static noise margin by 166.67% and power consumptionby 76.13% as compared to the FinFET based 6T SRAM

A novel optimization framework for controlling stabilization issue in design principle of FinFET based SRAM

The conventional design principle of the finFET offers various constraints that act as an impediment towards improving ther performance of finFET SRAM. After reviewing existing approaches, it has been found that there are not enough work found to be emphasizing on cost-effective optimization by addressing the stability problems in finFET design.Therefore, the proposed system introduces a novel optimization mechanism considering some essential design attributes e.g. area, thickness of fin, and number of components. The contribution of the proposed technique is to determine the better form of thickness of fin and its related aspect that can act as a solution to minimize various other asscoiated problems in finFET SRAM. Implemented using soft-computational approach, the proposed system exhibits that it offers better energy retention, lower delay, and potential capability to offer higher throughput irrespective of presence of uncertain amount of noise within the component

Ultra-low Power FinFET SRAM Cell with improved stability suitable for low power applications

In this paper, a new 11T SRAM cell using FinFET technology has been proposed, the basic component of the cell is the 6T SRAM cell with 4 NMOS access transistors to improve the stability and also makes it a dual port memory cell. The proposed cell uses a header scheme in which one extra PMOS transistor is used which is biased at different voltages to improve the read and write stability thus, helps in reducing the leakage power and active power. The cell shows improvement in RSNM (Read Static Noise Margin) with LP8T by 2.39x at sub-threshold voltage 2.68x with D6T SRAM cell, 5.5x with TG8T. The WSNM (Write Static Noise Margin) and HM (Hold Margin) of the SRAM cell at 0.9V is 306mV and 384mV. At sub-threshold operation also it shows improvement. The Leakage power reduced by 0.125x with LP8T, 0.022x with D6T SRAM cell, TG8T and SE8T. Also, impact of process variation on cell stability is discussed

Multi-Threshold Low Power-Delay Product Memory and Datapath Components Utilizing Advanced FinFET Technology Emphasizing the Reliability and Robustness

Indiana University-Purdue University Indianapolis (IUPUI)In this thesis, we investigated the 7 nm FinFET technology for its delay-power product performance. In our study, we explored the ASAP7 library from Arizona State University, developed in collaboration with ARM Holdings. The FinFET technology was chosen since it has a subthreshold slope of 60mV/decade that enables cells to function at 0.7V supply voltage at the nominal corner. An emphasis was focused on characterizing the Non-Ideal effects, delay variation, and power for the FinFET device. An exhaustive analysis of the INVx1 delay variation for different operating conditions was also included, to assess the robustness. The 7nm FinFET device was then employed into 6T SRAM cells and 16 function ALU. The SRAM cells were approached with advanced multi-corner stability evaluation. The system-level architecture of the ALU has demonstrated an ultra-low power system operating at 1 GHz clock frequency

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”

Design of High-Speed Dual Port 8T SRAM Cell with Simultaneous and Parallel READ-WRITE Feature

An innovative 8 transistor (8T) static random access memory (SRAM) architecture with a simple and reliable read operation is presented in this study. LTspice software is used to implement the suggested topology in the 16nm predictive technology model (PTM). Investigations into and comparisons with conventional 6T, 8T, 9T, and 10T SRAM cells have been made regarding read and write operations\u27 delay and power consumption as well as power delay product (PDP). The simulation outcomes show that the suggested design offers the fastest read operation and PDP optimization overall. Compared to the current 6T and 9T topologies, the noise margin is also enhanced. Finally, the comparison of the figure of merit (FoM) indicates the best efficiency of the proposed design

Novel High Performance Ultra Low Power Static Random Access Memories (SRAMs) Based on Next Generation Technologies

Title from PDF of title page viewed January 27, 2021Dissertation advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (page 107-120)Thesis (Ph.D.)--School of Computing and Engineering. University of Missouri--Kansas City, 2019Next Big Thing Is Surely Small: Nanotechnology Can Bring Revolution. Nanotechnology leads the world towards many new applications in various fields of computing, communication, defense, entertainment, medical, renewable energy and environment. These nanotechnology applications require an energy-efficient memory system to compute and process. Among all the memories, Static Random Access Memories (SRAMs) are high performance memories and occupies more than 50% of any design area. Therefore, it is critical to design high performance and energy-efficient SRAM design. Ultra low power and high speed applications require a new generation memory capable of operating at low power as well as low execution time. In this thesis, a novel 8T SRAM design is proposed that offers significantly faster access time and lowers energy consumption along with better read stability and write ability. The proposed design can be used in the conventional SRAM as well as in computationally intensive applications like neural networks and machine learning classifiers [1]-[4]. Novel 8T SRAM design offers higher energy efficiency, reliability, robustness and performance compared to the standard 6T and other existing 8T and 9T designs. It offers the advantages of a 10T SRAM without the additional area, delay and power overheads of the 10T SRAM. The proposed 8T SRAM would be able to overcome many other limitations of the conventional 6T and other 7T, 8T and 9T designs. The design employs single bitline for the write operation, therefore the number of write drivers are reduced. The defining feature of the proposed 8T SRAM is its hybrid design, which is the combination of two techniques: (i) the utilization of single-ended bitline and (ii) the utilization of virtual ground. The single-ended bitline technique ensures separate read and write operations, which eventually reduces the delay and power consumption during the read and write operations. It's independent read and write paths allow the use of the minimum sized access transistors and aid in a disturb-free read operation. The virtual ground weakens the positive feedback in the SRAM cell and improves its write ability. The virtual ground technique is also used to reduce leakages. The proposed design does not require precharging the bitlines for the read operation, which reduces the area and power overheads of the memory system by eliminating the precharging circuit. The design isolates the storage node from the read path, which improves the read stability. For reliability study, we have investigated the static noise margin (SNM) of the proposed 8T SRAM, for which, we have used two methods – (i) the traditional SNM method with the butterfly curve, (ii) the N-curve method A comparative analysis is performed between the proposed and the existing SRAM designs in terms of area, total power consumption during the read and write operations, and stability and reliability. All these advantages make the proposed 8T SRAM design an ideal candidate for the conventional and computationally intensive applications like machine learning classifier and deep learning neural network. In addition to this, there is need for next generation technologies to design SRAM memory because the conventional CMOS technology is approaching its physical and performance boundaries and as a consequence, becoming incompatible with ultra-low-power applications. Emerging devices such as Tunnel Field Effect Transistor (TFET)) and Graphene Nanoribbon Field Effect Transistor (GNRFET) devices are highly potential candidates to overcome the limitations of MOSFET because of their ability to achieve subthreshold slopes below 60 mV/decade and very low leakage currents [6]-[9]. This research also explores novel TFET and GNRFET based 6T SRAM. The thesis evaluates the standby leakage power in the Tunnel FET (TFET) based 6T SRAM cell for different pull-up, pull-down, and pass-gate transistors ratios (PU: PD: PG) and compared to 10nm FinFET based 6T SRAM designs. It is observed that the 10nm TFET based SRAMs have 107.57%, 163.64%, and 140.44% less standby leakage power compared to the 10nm FinFET based SRAMs when the PU: PD: PG ratios are 1:1:1, 1:5:2 and 2:5:2, respectively. The thesis also presents an analysis of the stability and reliability of sub-10nm TFET based 6T SRAM circuit with a reduced supply voltage of 500mV. The static noise margin (SNM), which is a critical measure of SRAM stability and reliability, is determined for hold, read and write operations of the 6T TFET SRAM cell. The robustness of the optimized TFET based 6T SRAM circuit is also evaluated at different supply voltages. Simulations were done in HSPICE and Cadence tools. From the analysis, it is clear that the main advantage of the TFET based SRAM would be the significant improvement in terms of leakage or standby power consumption. Compared to the FinFET based SRAM the standby leakage power of the T-SRAMs are 107.57%, 163.64%, and 140.44% less for 1:1:1, 1:5:2 and 2:5:2 configurations, respectively. Since leakage/standby power is the primary source of power consumption in the SRAM, and the overall system energy efficiency depends on SRAM power consumption, TFET based SRAM would lead to massive improvement of the energy efficiency of the system. Therefore, T-SRAMs are more suitable for ultra-low power applications. In addition to this, the thesis evaluates the standby leakage power of types of Graphene Nanoribbon FETs based 6T SRAM bitcell and compared to 10nm FinFET based 6T SRAM bitcell. It is observed that the 10nm MOS type GNRFET based SRAMs have 16.43 times less standby leakage power compared to the 10nm FinFET based SRAMs. The double gate SB-GNRFET based SRAM consumes 1.35E+03 times less energy compared to the 10nm FinFET based SRAM during write. However, during read double gate SB-GNRFET based SRAM consume 15 times more energy than FinFET based SRAM. It is also observed that GNRFET based SRAMs are more stable and reliable than FinFET based SRAM.Introduction -- Background -- Novel High Performance Ultra Low Power SRAM Design -- Tunnel FET Based SRAM Design -- Graphene Nanoribbon FET Based SRAM Design -- Double-gate FDSOI Based SRAM Designs -- Novel CNTFET and MEMRISTOR Based Digital Designs -- Conclusio

Cache memory design in the FinFET era

The major problem in the future technology scaling is the variations in process parameters that are interpreted as imperfections in the development process. Moreover, devices are more sensitive to the environmental changes of temperature and supply volt- age as well as to ageing. All these influences are manifested in the integrated circuits as increased power consumption, reduced maximal operating frequency and increased number of failures. These effects have been partially overcome with the introduction of the FinFET technology which have solved the problem of variability caused by Random Dopant Fluctuations. However, in the next ten years channel length is projected to shrink to 10nm where the variability source generated by Line Edge Roughness will dominate, and its effects on the threshold voltage variations will become critical. The embedded memories with their cells as the basic building unit are the most prone to these effects due to their the smallest dimensions. Because of that, memories should be designed with particular care in order to make possible further technology scaling. This thesis explores upcoming 10nm FinFETs and the existing issues in the cache memory design with this technology. More- over, it tries to present some original and novel techniques on the different level of design abstraction for mitigating the effects of process and environmental variability. At first original method for simulating variability of Tri-Gate Fin- FETs is presented using conventional HSPICE simulation environment and BSIM-CMG model cards. When that is accomplished, thorough characterisation of traditional SRAM cell circuits (6T and 8T) is performed. Possibility of using Independent Gate FinFETs for increasing cell stability has been explored, also. Gain Cells appeared in the recent past as an attractive alternative for in the cache memory design. This thesis partially explores this idea by presenting and performing detailed circuit analysis of the dynamic 3T gain cell for 10nm FinFETs. At the top of this work, thesis shows one micro-architecture optimisation of high-speed cache when it is implemented by 3T gain cells. We show how the cache coherency states can be used in order to reduce refresh energy of the memory as well as reduce memory ageing.El principal problema de l'escalat la tecnologia són les variacions en els paràmetres de disseny (imperfeccions) durant procés de fabricació. D'altra banda, els dispositius també són més sensibles als canvis ambientals de temperatura, la tensió d'alimentació, així com l'envelliment. Totes aquestes influències es manifesten en els circuits integrats com l'augment de consum d'energia, la reducció de la freqüència d'operació màxima i l'augment del nombre de xips descartats. Aquests efectes s'han superat parcialment amb la introducció de la tecnologia FinFET que ha resolt el problema de la variabilitat causada per les fluctuacions de dopants aleatòries. No obstant això, en els propers deu anys, l'ample del canal es preveu que es reduirà a 10nm, on la font de la variabilitat generada per les rugositats de les línies de material dominarà, i els seu efecte en les variacions de voltatge llindar augmentarà. Les memòries encastades amb les seves cel·les com la unitat bàsica de construcció són les més propenses a sofrir aquests efectes a causa de les seves dimensions més petites. A causa d'això, cal dissenyar les memòries amb una especial cura per tal de fer possible l'escalat de la tecnologia. Aquesta tesi explora la tecnologia de FinFETs de 10nm i els problemes existents en el disseny de memòries amb aquesta tecnologia. A més a més, presentem noves tècniques originals sobre diferents nivells d'abstracció del disseny per a la mitigació dels efectes les variacions tan de procés com ambientals. En primer lloc, presentem un mètode original per a la simulació de la variabilitat de Tri-Gate FinFETs usant entorn de simulació HSPICE convencional i models de tecnologia BSIMCMG. Després, es realitza la caracterització completa dels circuits de cel·les SRAM tradicionals (6T i 8T) conjuntament amb l'ús de Gate-independent FinFETs per augmentar l'estabilitat de la cèl·lula