Topology Derivation and Development of Non-Isolated Three-port Converters for DC Microgrids

Currently, three-port converters (TPCs) are gaining popularity in applications which integrate renewable energies, such as photovoltaics and wind, and energy storage elements, such as batteries and supercapacitors with load. This is due to the advantages of a single power conversion stage between any two ports for better conversion efficiency and a highly integrated structure for compactness. Most of the reported TPCs focus on the consuming load. However, there are applications such as hybrid-electric vehicle braking systems and DC microgrids which have power generating capability. A typical example is battery charging in a DC microgrid. When the photovoltaics has inadequate power to charge the battery, the TPCs that consider only consuming load need an extra DC/DC converter for the DC bus to charge the battery. Three-winding transformers associated with full-bridge configurations as the basis for TPCs can fulfill the purpose of bi-directional power flow between any two ports. However, bulkiness of transformers and the need for more switches and associated control mechanisms increases the converter complexity, volume and cost. Solutions for integrating a regenerative load in NITPCs are still limited. This research work focuses on the development of non-isolated three-port converters (NITPCs), as they are capable of driving a regenerative load while offering a compact solution. The study includes a systematic approach to deriving a family of NITPCs. They combine different commonly known power converters in an integrated manner while considering the voltage polarity, voltage levels among the ports and overall voltage conversion ratio. The derived converter topologies allow for all possible power flow combinations among the sources and load while preserving the single power processing feature of the TPC. A design example of a boost converter based TPC with a bi-directional buck converter is reported. In addition, a novel single-inductor NITPC is proposed. It is a further integrated topology according to the aforementioned design example where only one inductor is required instead of two, and the number of power transistors remains the same. The detailed topological derivation, operation principles, steady-state analysis, simulation results and experiment results are given to verify the proposed NITPCs

Analysis of a new family of DC-DC converters with input-parallel output-series structure

There is an increasing trend of development and installation of switching power supplies due to their highly efficient power conversion, fast power control and high quality power conditioning for applications such as renewable energy integration and energy storage management systems. In most of these applications, high voltage conversion ratio is required. However, basic switching converters have limited voltage conversion ratio. There has been much research into development of high gain power converters. While most of the reported topologies focus on high gain and high efficiency, in this thesis, the input and output ripple currents and reliability are also considered to derive a new converter structure suitable for high step-up voltage conversion applications. High ripple currents and voltages at the input and output of dc-dc converters are not desirable because they may affect the operation of the dc source or the load. A number of converters operating in an interleaved manner can reduce these ripples. This thesis proposes a dc/dc switching converter structure which is capable of reducing the ripple problem through interleaved action, in addition to high gain and high efficiency voltage conversion. The thesis analyses the proposed converter structure through a dual buck-boost converter topology. The structure allows different converter topologies and combinations of them for different applications to be configured. The study begins with a motivation and a literature review of dc/dc converters. The new family of high step-up converters is introduced with an interleaved buck-boost as an example, followed by small-signal analysis. Experimental verifications, conclusions and future work are discussed

Analysis of a new family of DC-DC converters with input-parallel output-series structure

There is an increasing trend of development and installation of switching power supplies due to their highly efficient power conversion, fast power control and high quality power conditioning for applications such as renewable energy integration and energy storage management systems. In most of these applications, high voltage conversion ratio is required. However, basic switching converters have limited voltage conversion ratio. There has been much research into development of high gain power converters. While most of the reported topologies focus on high gain and high efficiency, in this thesis, the input and output ripple currents and reliability are also considered to derive a new converter structure suitable for high step-up voltage conversion applications. High ripple currents and voltages at the input and output of dc-dc converters are not desirable because they may affect the operation of the dc source or the load. A number of converters operating in an interleaved manner can reduce these ripples. This thesis proposes a dc/dc switching converter structure which is capable of reducing the ripple problem through interleaved action, in addition to high gain and high efficiency voltage conversion. The thesis analyses the proposed converter structure through a dual buck-boost converter topology. The structure allows different converter topologies and combinations of them for different applications to be configured. The study begins with a motivation and a literature review of dc/dc converters. The new family of high step-up converters is introduced with an interleaved buck-boost as an example, followed by small-signal analysis. Experimental verifications, conclusions and future work are discussed

Generic closed loop controller for power regulation in dual active bridge DC-DC converter with current stress minimization

This paper presents a comprehensive and generalized analysis of the bidirectional dual active bridge (DAB) DC/DC converter using triple phase shift (TPS) control to enable closed loop power regulation while minimizing current stress. The key new achievements are: a generic analysis in terms of possible conversion ratios/converter voltage gains (i.e. Buck/Boost/Unity), per unit based equations regardless of DAB ratings, and a new simple closed loop controller implementable in real time to meet desired power transfer regulation at minimum current stress. Per unit based analytical expressions are derived for converter AC RMS current as well as power transferred. An offline particle swarm optimization (PSO) method is used to obtain an extensive set of TPS ratios for minimizing the RMS current in the entire bidirectional power range of - 1 to 1 per unit. The extensive set of results achieved from PSO presents a generic data pool which is carefully analyzed to derive simple useful relations. Such relations enabled a generic closed loop controller design that can be implemented in real time avoiding the extensive computational capacity that iterative optimization techniques require. A detailed Simulink DAB switching model is used to validate precision of the proposed closed loop controller under various operating conditions. An experimental prototype also substantiates the results achieved

Three-Phase Reduced Switch Topologies for AC-DC Front-End and Single-Stage Converters

Conventional three-phase ac-dc converters have two converter stages. They have a front-end converter that converts the input ac voltage into an intermediate dc bus voltage and a second, back-end converter that converts this dc bus voltage into the desired isolated dc output voltage. The front-end converter also performs power factor correction (PFC) and shapes the three-phase input currents so that they are nearly sinusoidal and in phase with the three-phase input voltages. This allows the ac power source to be used in the most efficient manner. The front-end ac-dc converter is typically implemented with six switches while the back-end dc-dc converter is typically implemented with a four switch dc-dc full-bridge topology. Power electronic researchers have been motivated to try to reduce the number of switches that are used in the conventional two-stage approach in order to reduce cost and simplify the overall ac-dc converter. There are two general approaches to doing this: This first approach is to reduce the number of switches in the front-end ac-dc converter. The second approach is to combine the ac-dc converter and the dc-dc converter in a single converter so that the overall ac-dc converter can be implemented in a single converter stage that can simultaneously perform ac-dc power conversion with PFC and dc-dc power conversion. The main focus of this thesis is on new power converter topologies that convert a three-phase ac input voltage into an isolated dc output voltage with a reduced number of switches. In the thesis, a new family of reduced switch front-end converter topologies is proposed, an example converter from this new family is selected for further study and a modified version of this topology is studied as well. In addition to these front-end converters, two new three-phase ac-dc single-stage converters are proposed and their properties and characteristics are compared. For each new converter that is investigated in detail, its modes of operation are explained, its steady-state characteristics are determined by mathematical analysis, and the results of the analysis are used to develop a design procedure that can be used to select key components. The design procedure of each new converter is demonstrated with an example that was used in the implementation of an experimental prototype that confirmed the feasibility of the converter. The thesis concludes by presenting that have been reached as a result of the work that was performed, stating its main contributions to the power electronics literature and suggesting future research that can be done based on the thesis work

A Comprehensive Review of DC-DC Converters for EV Applications

DC-DC converters in Electric vehicles (EVs) have the role of interfacing power sources to the DC-link and the DC-link to the required voltage levels for usage of different systems in EVs like DC drive, electric traction, entertainment, safety and etc. Improvement of gain and performance in these converters has a huge impact on the overall performance and future of EVs. So, different configurations have been suggested by many researches. In this paper, bidirectional DC-DC converters (BDCs) are divided into four categories as isolated-soft, isolated-hard, non-isolated-soft and non-isolated-hard depending on the isolation and type of switching. Moreover, the control strategies, comparative factors, selection for a specific application and recent trends are reviewed completely. As a matter of fact, over than 200 papers have been categorized and considered to help the researchers who work on BDCs for EV application

Analysis, design, and implementation of the AFZ converter applied to photovoltaic systems

Grid-tied photovoltaic (PV) installations with Distributed Maximum Power Point Tracking (DMPPT) architectures include a DC-DC Module Integrated Converter (MIC) for managing each PV panel, isolating it from the others, reducing the mismatching effect and maximizing the harvested power. In this paper, the Autotransformer Forward converter with type-Zeta resonant reset (AFZ) is proposed as a DMPPT architecture’s MIC candidate. The main characteristics of the AFZ converter are the high versatility due to its voltage step-up and step-down capability; the use of an optimized autotransformer with only two windings, reducing the complexity and power losses of this component; the good dynamic performances, like the Forward converter ones; the low number of components and the simplicity and high feasibility associated to the use of just one active switch. Besides, soft switching transitions are achieved thanks to the autotransformer type-Zeta resonant reset. The steady-state theoretical analysis, considering the effect of the autotransformer leakage inductance, is presented. The converter is also studied in the frequency domain, obtaining the small-signal transfer functions. A design procedure based on the requirements of a 100 kW grid-tied photovoltaic installation is described, yielding in a 225 W prototype with efficiencies up to 95.6 %. Experimental results validate the theoretical analysis.This work was supported in part by the Spanish Ministry of Economy and Competitiveness and FEDER funds through the research project “Storage and Energy Management for Hybrid Electric Vehicles based on Fuel Cell, Battery and Supercapacitors” ELECTRICAR-AG under Grant DPI2014-53685-C2-1-R, in part by the research project CONEXPOT under Grant DPI2017-84572-C2-2-R, and in part by the research project EPIIOT under Grant DPI2017-88062-R

Design and Control of Power Converters 2019

In this book, 20 papers focused on different fields of power electronics are gathered. Approximately half of the papers are focused on different control issues and techniques, ranging from the computer-aided design of digital compensators to more specific approaches such as fuzzy or sliding control techniques. The rest of the papers are focused on the design of novel topologies. The fields in which these controls and topologies are applied are varied: MMCs, photovoltaic systems, supercapacitors and traction systems, LEDs, wireless power transfer, etc