Simulating the Impact of Traffic Calming Strategies

This study assessed the impact of traffic calming measures to the speed, travel times and capacity of residential roadways. The study focused on two types of speed tables, speed humps and a raised crosswalk. A moving test vehicle equipped with GPS receivers that allowed calculation of speeds and determination of speed profiles at 1s intervals were used. Multi-regime model was used to provide the best fit using steady state equations; hence the corresponding speed-flow relationships were established for different calming scenarios. It was found that capacities of residential roadway segments due to presence of calming features ranged from 640 to 730 vph. However, the capacity varied with the spacing of the calming features in which spacing speed tables at 1050 ft apart caused a 23% reduction in capacity while 350-ft spacing reduced capacity by 32%. Analysis showed a linear decrease of capacity of approximately 20 vphpl, 37 vphpl and 34 vphpl when 17 ft wide speed tables were spaced at 350 ft, 700 ft, and 1050 ft apart respectively. For speed hump calming features, spacing humps at 350 ft reduced capacity by about 33% while a 700 ft spacing reduced capacity by 30%. The study concludes that speed tables are slightly better than speed humps in terms of preserving the roadway capacity. Also, traffic calming measures significantly reduce the speeds of vehicles, and it is best to keep spacing of 630 ft or less to achieve desirable crossing speeds of less or equal to 15 mph especially in a street with schools nearby. A microscopic simulation model was developed to replicate the driving behavior of traffic on urban road diets roads to analyze the influence of bus stops on traffic flow and safety. The impacts of safety were assessed using surrogate measures of safety (SSAM). The study found that presence of a bus stops for 10, 20 and 30 s dwell times have almost 9.5%, 12%, and 20% effect on traffic speed reductions when 300 veh/hr flow is considered. A comparison of reduction in speed of traffic on an 11 ft wide road lane of a road diet due to curbside stops and bus bays for a mean of 30s with a standard deviation of 5s dwell time case was conducted. Results showed that a bus stop bay with the stated bus dwell time causes an approximate 8% speed reduction to traffic at a flow level of about 1400 vph. Analysis of the trajectories from bust stop locations showed that at 0, 25, 50, 75, 100, 125, 150, and 175 feet from the intersection the number of conflicts is affected by the presence and location of a curbside stop on a segment with a road diet

Microsimulation models incorporating both demand and supply dynamics

There has been rapid growth in interest in real-time transport strategies over the last decade, ranging from automated highway systems and responsive traffic signal control to incident management and driver information systems. The complexity of these strategies, in terms of the spatial and temporal interactions within the transport system, has led to a parallel growth in the application of traffic microsimulation models for the evaluation and design of such measures, as a remedy to the limitations faced by conventional static, macroscopic approaches. However, while this naturally addresses the immediate impacts of the measure, a difficulty that remains is the question of how the secondary impacts, specifically the effect on route and departure time choice of subsequent trips, may be handled in a consistent manner within a microsimulation framework. The paper describes a modelling approach to road network traffic, in which the emphasis is on the integrated microsimulation of individual trip-makers’ decisions and individual vehicle movements across the network. To achieve this it represents directly individual drivers’ choices and experiences as they evolve from day-to-day, combined with a detailed within-day traffic simulation model of the space–time trajectories of individual vehicles according to car-following and lane-changing rules and intersection regulations. It therefore models both day-to-day and within-day variability in both demand and supply conditions, and so, we believe, is particularly suited for the realistic modelling of real-time strategies such as those listed above. The full model specification is given, along with details of its algorithmic implementation. A number of representative numerical applications are presented, including: sensitivity studies of the impact of day-to-day variability; an application to the evaluation of alternative signal control policies; and the evaluation of the introduction of bus-only lanes in a sub-network of Leeds. Our experience demonstrates that this modelling framework is computationally feasible as a method for providing a fully internally consistent, microscopic, dynamic assignment, incorporating both within- and between-day demand and supply dynamic

Integrating big data into a sustainable mobility policy 2.0 planning support system

It is estimated that each of us, on a daily basis, produces a bit more than 1 GB of digital content through our mobile phone and social networks activities, bank card payments, location-based positioning information, online activities, etc. However, the implementation of these large data amounts in city assets planning systems still remains a rather abstract idea for several reasons, including the fact that practical examples are still very strongly services-oriented, and are a largely unexplored and interdisciplinary field; hence, missing the cross-cutting dimension. In this paper, we describe the Policy 2.0 concept and integrate user generated content into Policy 2.0 platform for sustainable mobility planning. By means of a real-life example, we demonstrate the applicability of such a big data integration approach to smart cities planning process. Observed benefits range from improved timeliness of the data and reduced duration of the planning cycle to more informed and agile decision making, on both the citizens and the city planners end. The integration of big data into the planning process, at this stage, does not have uniform impact across all levels of decision making and planning process, therefore it should be performed gradually and with full awareness of existing limitations

Bus rapid transit

Effective public transit is central to development. For the vast majority of developing city residents, public transit is the only practical means to access employment, education, and public services, especially when such services are beyond the viable distance of walking or cycling. Unfortunately, the current state of public transit services in developing cities often does little to serve the actual mobility needs of the population. Bus services are too often unreliable, inconvenient and dangerous. In response, transport planners and public officials have sometimes turned to extremely costly mass transit alternatives such as rail-based metros. Due to the high costs of rail infrastructure, cities can only construct such systems over a few kilometres in a few limited corridors. The result is a system that does not meet the broader transport needs of the population. Nevertheless, the municipality ends up with a long-term debt that can affect investment in more pressing areas such as health, education, water, and sanitation. However, there is an alternative between poor public transit service and high municipal debt. Bus Rapid Transit (BRT) can provide high-quality, metro-like transit service at a fraction of the cost of other options. This document provides municipal officials, non-governmental organizations, consultants, and others with an introduction to the concept of BRT as well as a step-by-step process for successfully planning a BRT system

Safe driving in a green world : a review of driver performance benchmarks and technologies to support ‘smart’ driving

Road transport is a significant source of both safety and environmental concerns. With climate change and fuel prices increasingly prominent on social and political agendas, many drivers are turning their thoughts to fuel efficient or ‘green’ (i.e., environmentally friendly) driving practices. Many vehicle manufacturers are satisfying this demand by offering green driving feedback or advice tools. However, there is a legitimate concern regarding the effects of such devices on road safety – both from the point of view of change in driving styles, as well as potential distraction caused by the in-vehicle feedback. In this paper, we appraise the benchmarks for safe and green driving, concluding that whilst they largely overlap, there are some specific circumstances in which the goals are in conflict. We go on to review current and emerging in-vehicle information systems which purport to affect safe and/or green driving, and discuss some fundamental ergonomics principles for the design of such devices. The results of the review are being used in the Foot-LITE project, aimed at developing a system to encourage ‘smart’ – that is safe and green – driving

Eco-driving technology for sustainable road transport: A review

© 2018 Elsevier Ltd Road transport consumes significant quantities of fossil fuel and accounts for a significant proportion of CO2 and pollutant emissions worldwide. The driver is a major and often overlooked factor that determines vehicle performance. Eco-driving is a relatively low-cost and immediate measure to reduce fuel consumption and emissions significantly. This paper reviews the major factors, research methods and implementation of eco-driving technology. The major factors of eco-driving are acceleration/deceleration, driving speed, route choice and idling. Eco-driving training programs and in-vehicle feedback devices are commonly used to implement eco-driving skills. After training or using in-vehicle devices, immediate and significant reductions in fuel consumption and CO2 emissions have been observed with slightly increased travel time. However, the impacts of both methods attenuate over time due to the ingrained driving habits developed over the years. These findings imply the necessity of developing quantitative eco-driving patterns that could be integrated into vehicle hardware so as to generate more constant and uniform improvements, as well as developing more effective and lasting training programs and in-vehicle devices. Current eco-driving studies mainly focus on the fuel savings and CO2 reduction of individual vehicles, but ignore the pollutant emissions and the impacts at network levels. Finally, the challenges and future research directions of eco-driving technology are elaborated

Technology assessment of future intercity passenger transporation systems. Volume 1: Summary report

Technical, economic, environmental, and sociopolitical issues associated with future intercity transportation system options were assured. Technology assessment was used as a tool to assist in the identification of basic research and technology development tasks that should be undertaken. The emphasis was on domestic passenger transportation, but interfaces with freight and international transportation were considered

micro and macro modelling approaches for the evaluation of the carbon impacts of transportation

Abstract To quantify CO2 emissions from road transport, literature suggests the adoption of several alternative methods, based on transport modelling and carbon modules. Some of these methods are labelled as a micro approach and others as a macro approach. Their distinction is made according to the temporal and spatial horizons, the aim of the study and the degree of accuracy required. This paper presents these methods and discusses their appropriateness, whereby special focus is laid on the potential of the micro approach on ICT, based on a literature review of several European projects. We conclude that the adoption of the micro approach, is quite promising – mostly at the urban level, despite the computational efforts required and the technical difficulties to model driver behaviors. Thus, further research is required to overcome the numerous sources of scientific uncertainties