233 research outputs found
Recommended from our members
Design and implementation of Radix-3/Radix-2 based novel hybrid SAR ADC in scaled CMOS technologies
This thesis focuses on low power and high speed design techniques for successive
approximation register (SAR) analog-to-digital converters (ADCs) in nanoscale
CMOS technologies. SAR ADCs’ speed is limited by the number of bits of
resolution. An N-bit conventional SAR ADC takes N conversion cycles. To speed
up the conversion process, we introduce a radix-3 SAR ADC which can compute
1:6 bits per cycle. To our knowledge, it is the first fully programmable and efficiently
hardware controlled radix-3 SAR ADC. We had to use two comparators per
cycle due to ADC architecture and we proposed a simple calibration scheme for
the comparators. Also, as the architecture of the DAC array is completely different
from the architecture of conventional radix-2 SAR ADC’s DAC arrays, we came up
with an algorithm for calibration of capacitors of the DAC.
Low power SAR ADCs face two major challenges especially at high resolutions:
(1) increased comparator power to suppress the noise, and (2) increased
DAC switching energy due to the large DAC size. Due to our proposed architecture,the radix-3 SAR ADC uses two comparators per cycle and two differential DACs.
To improve the comparator’s power efficiency, an efficient and low cost calibration
technique has been introduced. It allows a low power and noisy comparator to
achieve high signal-to-noise ratio (SNR).
To improve the DAC switching energy, we introduced a radix-3/radix-2
based novel hybrid SAR ADC. We use two single ended DACs for radix-3 SAR
ADC and these two single ended DACs can be used as one differential DAC for
radix-2 SAR ADC. So, overall, we only have a single DAC as conventional radix-
2 SAR ADC. In addition, a monotonic switching technique is adopted for radix-2
search to reduce the DAC capacitor size and hence, to reduce switching power. It
can reduce the total number of unit capacitors by four times. Our proposed hybrid
SAR ADC can achieve less DAC energy compared to radix-3 and radix-2 SAR
ADCs. Also, to utilize technology scaling, we used the minimum capacitor size
allowed by thermal noise limitations. To achieve high resolution, we introduced
calibration algorithm for the DAC array.
As mentioned earlier, the radix-3 SAR ADC offers higher power than conventional
radix-2 SAR ADC because of simultaneous use of two comparators. In
the proposed hybrid SAR ADC, we will be using radix-3 search for first few MSB
bits. So, the resolution required for radix-3 comparators are much larger than the
LSB value of 10-bit ADC. By implementing calibration of comparators, we can
use low power, high input referred offset and high speed comparators for radix-3
search. Radix-2 search will be used for rest of the bits and the resolution of the
radix-2 comparator has to be less than the required LSB value. So, a high power, low input referred offset and high speed comparator is used for radix-2 search.
Also, we introduced clock gating for comparators. So, radix-3 comparators will not
toggle during radix-2 search and the radix-2 comparators will be inactive during
radix-3 search. By using the aforementioned techniques, the overall comparator
power is definitely less than a radix-3 SAR ADC and comparable to a conventional
radix-2 SAR ADC.
A prototype radix-3/radix-2 based hybrid SAR ADC with the proposed
technique is designed and fabricated in 40nm CMOS technology. It achieves an
SNDR of 56.9 dB and consumes only 0.38 mW power at 30MS/s, leading to a
Walden figure of merit of 21.5 fJ/conv-step.Electrical and Computer Engineerin
Recommended from our members
Design techniques for low-power SAR ADCs in nano-scale CMOS technologies
This thesis presents low power design techniques for successive approximation register (SAR) analog-to-digital converters (ADCs) in nano-scale CMOS technologies. Low power SAR ADCs face two major challenges especially at high resolutions: (1) increased comparator power to suppress the noise, and (2) increased DAC switching energy due to the large DAC size. To improve the comparator’s power efficiency, a statistical estimation based comparator noise reduction technique is presented. It allows a low power and noisy comparator to achieve high signal-to-noise ratio (SNR) by estimating the conversion residue. A first prototype ADC in 65nm CMOS has been developed to validate the proposed noise reduction technique. It achieves 4.5 fJ/conv-step Walden figure of merit and 64.5 dB signal-to-noise and distortion ratio (SNDR). In addition, a bidirectional single-side switching technique is developed to reduce the DAC switching power. It can reduce the DAC switching power and the total number of unit capacitors by 86% and 75%, respectively. A second prototype ADC with the proposed switching technique is designed and fabricated in 180nm CMOS technology. It achieves an SNDR of 63.4 dB and consumes only 24 Wat 1MS/s, leading to aWalden figure of merit of 19.9 fJ/conv-step. This thesis also presents an improved loop-unrolled SAR ADC, which works at high frequency with reduced SAR logic power and delay. It employs the bidirectional single-side switching technique to reduce the comparator common-mode voltage variation. In addition, it uses a Vcm-adaptive offset calibration technique which can accurately calibrate comparator’s offset at its operating Vcm. A prototype ADC designed in 40nm CMOS achieves 35 dB at 700 MS/s sampling rate and consumes only 0.95 mW, leading to a Walden figure of merit of 30 fJ/conv-step.Electrical and Computer Engineerin
Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications
As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well
Study of a Time Assisted SAR ADC
The demand for low power systems has been increasing in recent years and Analogto-
Digital Converters (ADCs) are key blocks of many of these systems as they convert a
physical quantity into the digital domain so that this information can be further processed or stored using digital techniques.
Data Converters based on Charge Redistribution using of Successive Approximation
Registers (SAR) are becoming one of the most popular ADC architectures for moderate
speed, medium resolution and low power applications. Due to their low analog complexity SAR ADCs benefit from technology scaling. However, this scaling often comes with a supply voltage reduction and the noise levels do not decrease at the same rate, which translates into a performance decrease. Therefore, new opportunities emerge to explore other physical quantities such as time, frequency, phase or charge in the circuit.
This thesis focuses on studying how the time domain information can be used to
increase the performance of SAR ADCs. To do so, a new SAR ADC architecture is proposed in which a Time-to-Digital Converter (TDC) is used to convert the time domain information, provided by the comparator, into the digital domain. This new architecture was modelled in MATLAB as a 12 bit TDC assisted SAR ADC, using information from electrical simulations of the comparator and the TDC, designed in Cadence in 65 nm ST Microelectronics CMOS technology.
Simulation results demonstrated that, to achieve a better performance when compared
to more traditional SAR structures, the TDC energy and latency should be minimized.
Another limiting factor was the large voltage range in which only 1 bit could be extracted from the time-to-voltage conversion by the TDC due to the comparator’s fast response in this range. The proposed architecture was also extended to incorporate a Bypass Window in the time domain, which allowed to substantially decrease the number of clock cycles necessary to solve the 12 bits of the ADC
High speed – energy efficient successive approximation analog to digital converter using tri-level switching
This thesis reports issues and design methods used to achieve high-speed and high-resolution Successive Approximation Register analog to digital converters (SAR ADCs). A major drawback of this technique relates to the mismatch in the binary ratios of capacitors which causes nonlinearity. Another issue is the use of large capacitors due to nonlinear effect of parasitic capacitance. Nonlinear effect of capacitor mismatch is investigated in this thesis. Based on the analysis, a new Tri-level switching algorithm is proposed to reduce the matching requirement for capacitors in SAR ADCs. The integral non-linearity (INL) and the differential non-linearity (DNL) of the proposed scheme are reduced by factor of two over conventional SAR ADC, which is the lowest compared to the previously reported schemes. In addition, the switching energy of the proposed scheme is reduced by 98.02% compared with the conventional SAR architecture. A new correction method to solve metastability error of comparator based on a novel design approach is proposed which reduces the required settling time about 1.1τ for each conversion cycle. Based on the above proposed methods two SAR ADCs: an 8-bit SAR ADC with 50MS/sec sampling rate, and a 10-bit SAR split ADC with 70 MS/sec sampling rate have been designed in 0.18μm Silterra complementary metal oxide semiconductor (CMOS) technology process which works at 1.2V supply voltage and input voltage of 2.4Vp-p. The 8-bit ADC digitizes 25MHz input signal with 48.16dB signal to noise and distortion ratio (SNDR) and 52.41dB spurious free dynamic range (SFDR) while consuming about 589μW. The figure of merit (FOM) of this ADC is 56.65 fJ/conv-step. The post layout of the 10-bit ADC with 1MHz input frequency produces SNDR, SFDR and effective number of bits (ENOB) of 57.1dB, 64.05dB and 9.17Bit, respectively, while its DNL and INL are -0.9/+2.8 least significant bit (LSB) and -2.5/+2.7 LSB, respectively. The total power consumption, including digital, analog and reference power, is 1.6mW. The FOM is 71.75fJ/conv. step
Recommended from our members
Noise shaping Asynchronous SAR ADC based time to digital converter
Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin
A 9.38-bit, 422nW, high linear SAR-ADC for wireless implantable system
In wireless implantable systems (WIS) low power consumption and linearity are the most prominent performance metrics in data acquisition systems. successive approximation register-analog to digital converter (SAR-ADC) is used for data processing in WIS. In this research work, a 10-bit low power high linear SAR-ADC has been designed for WIS. The proposed SAR-ADC architecture is designed using the sample and hold (S/H) circuit consisting of a bootstrap circuit with a dummy switch. This SAR-ADC has a dynamic latch comparator, a split capacitance digital to analog converter (SC-DAC) with mismatch calibration, and a SAR using D-flipflop. This architecture is designed in 45 nm CMOS technology. This ADC reduces non-linearity errors and improve the output voltage swing due to the usage of a clock booster and dummy switch in the sample and hold. The calculated outcomes of the proposed SAR ADC display that with on-chip calibration an ENOB of 9.38 (bits), spurious free distortion ratio (SFDR) of 58.621 dB, and ± 0.2 LSB DNL and ± 0.4LSB INL after calibration
Capacitance-to-Digital Converter for Ultra-Low-Power Wireless Sensor Nodes
Power consumption is one of the main design constraints in today’s integrated circuits. For systems like wearable electronics, UAVs, IOT systems powered by batteries which are charged using the energy harvested from various sources like RF, Thermal, Solar and Vibration, ultra-low power consumption is paramount. In these systems, Transducers which convert physical parameters into electrical parameters and the analog-to-digital converters (ADCs) are key components as the interface between the analog world and the digital domain. This thesis addresses the design challenges, strategies, as well as circuit techniques of ultra-low-power signal Front End used in several low power electronic systems in general and pressure measurement systems in particular.
In this thesis, Capacitance to Digital Converter based pressure measurement system has been implemented. Here we present a general-purpose, wide-range CDC that combines a correlated double sampling (CDS) approach with a differential asynchronous SAR ADC. Since the sensor capacitor is sampled only twice per conversion, energy per conversion is low. Furthermore, since the CDS separates the sensor capacitor from the CDAC, a full differential input voltage range is preserved. The CDC has a 2.5-to-75.5pF conversion range. Monotonic SAR ADC was designed in 180nm CMOS with 1-V power supply and a 1-kS/s sampling rate with switching energy of about 100nW
Noise-Shaping SAR ADCs: From Discrete Time to Continuous Time
Noise-shaping (NS) SAR ADCs become popular recently, thanks to their low-power and high-resolution features. This article first summarizes and benchmarks different discrete-time (DT) NS-SAR implementations in literature. An open-loop duty-cycled residue amplifier is selected as a power-efficient solution to realize high residue gain. Then, a digital-predicted mismatch error shaping technique is introduced to improve the DAC linearity. The proposed DT NS-SAR ADC achieves 80 dB SNDR and 98 dB SFDR in a 31.25 kHz bandwidth while consuming 7.3 μW. Next, the NS-SAR architecture is extended from DT operation to continuous-time (CT) operation. The ADC sampling switch is removed, and the loop filter is duty cycled to realize the CT NS-SAR operation. Compared to DT designs, the CT NS-SAR ADC is easy to drive and has an inherent anti-aliasing function. As a proof of concept, the proposed CT NS-SAR ADC achieves 77 dB SNDR and 86 dB SFDR in a 62.5 kHz bandwidth with a power consumption of 13.5 μW
- …