Self-Adaptive Architecture for Multi-sensor Embedded Vision System

International audienceArchitectural optimization for heterogeneous multi-sensor processing is a real technological challenge. Most of the vision systems involve only one single color sensor and they do not address the heterogeneous sensors challenge. However, more and more applications require other types of sensor in addition, such as infrared or low-light sensor, so that the vision system could face various luminosity conditions. These heterogeneous sensors could differ in the spectral band, the resolution or even the frame rate. Such sensor variety needs huge computing performance , but embedded systems have stringent area and power constraints. Reconfigurable architecture makes possible flexible computing while respecting the latter constraints. Many reconfigurable architectures for vision application have been proposed in the past. Yet, few of them propose a real dynamic adaptation capability to manage sensor heterogeneity. In this paper, a self-adaptive architecture is proposed to deal with heterogeneous sensors dynamically. This architecture supports on-the-fly sensor switch. Architecture of the system is self-adapted thanks to a system monitor and an adaptation controller. A stream header concept is used to convey sensor information to the self-adaptive architecture. The proposed architecture was implemented in Altera Cyclone V FPGA. In this implementation, adaptation of the architecture consists in Dynamic and Partial Reconfiguration of FPGA. The self-adaptive ability of the architecture has been proved with low resource overhead and an average global adaptation time of 75 ms

Information processing in info-communication media of geodynamic monitoring on the basis of adaptive queuing system

The paper considers the problem of modeling the processing of geodynamic information in a reconfigurable information-communication environment of geodynamic monitoring based on an adaptive queuing system. It was established that due to the complexity and diversity of geodynamic information, the number of geodynamic control points is expanding and the number of controlled parameters, the number of controlled objects of natural-technical systems (NTS) are increasin

Circuit-Variant Moving Target Defense for Side-Channel Attacks on Reconfigurable Hardware

With the emergence of side-channel analysis (SCA) attacks, bits of a secret key may be derived by correlating key values with physical properties of cryptographic process execution. Power and Electromagnetic (EM) analysis attacks are based on the principle that current flow within a cryptographic device is key-dependent and therefore, the resulting power consumption and EM emanations during encryption and/or decryption can be correlated to secret key values. These side-channel attacks require several measurements of the target process in order to amplify the signal of interest, filter out noise, and derive the secret key through statistical analysis methods. Differential power and EM analysis attacks rely on correlating actual side-channel measurements to hypothetical models. This research proposes increasing resistance to differential power and EM analysis attacks through structural and spatial randomization of an implementation. By introducing randomly located circuit variants of encryption components, the proposed moving target defense aims to disrupt side-channel collection and correlation needed to successfully implement an attac

A Model of Computation for Reconfigurable Systems

The dissertation introduces RecDEVS, a model of computation for reconfigurable hardware systems. Existing computational models for conventional hardware structures are not suited very well to model the dynamic behavior of reconfigurable systems. This work first systematically investigates the requirements that are necessary to properly model reconfigurable systems. Then, the Discrete Event System Specification (DEVS) formalism is extended into RecDEVS, a formalism capable of modeling reconfigurable systems. It is then demonstrated how RecDEVS can be utilized to do a a model based design flow that eases system verification

Models, Design Methods and Tools for Improved Partial Dynamic Reconfiguration

Partial dynamic reconfiguration of FPGAs has attracted high attention from both academia and industry in recent years. With this technique, the functionality of the programmable devices can be adapted at runtime to changing requirements. The approach allows designers to use FPGAs more efficiently: E. g. FPGA resources can be time-shared between different functions and the functions itself can be adapted to changing workloads at runtime. Thus partial dynamic reconfiguration enables a unique combination of software-like flexibility and hardware-like performance. Still there exists no common understanding on how to assess the overhead introduced by partial dynamic reconfiguration. This dissertation presents a new cost model for both the runtime and the memory overhead that results from partial dynamic reconfiguration. It is shown how the model can be incorporated into all stages of the design optimization for reconfigurable hardware. In particular digital circuits can be mapped onto FPGAs such that only small fractions of the hardware must be reconfigured at runtime, which saves time, memory, and energy. The design optimization is most efficient if it is applied during high level synthesis. This book describes how the cost model has been integrated into a new high level synthesis tool. The tool allows the designer to trade-off FPGA resource use versus reconfiguration overhead. It is shown that partial reconfiguration causes only small overhead if the design is optimized with regard to reconfiguration cost. A wide range of experimental results is provided that demonstrates the benefits of the applied method.:1 Introduction 1 1.1 Reconfigurable Computing . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1.1 Reconfigurable System on a Chip (RSOC) . . . . . . . . . . . . 4 1.1.2 Anatomy of an Application . . . . . . . . . . . . . . . . . . . . . . 6 1.1.3 RSOC Design Characteristics and Trade-offs . . . . . . . . . . . 7 1.2 Classification of Reconfigurable Architectures . . . . . . . . . . . . . . . 10 1.2.1 Partial Reconfiguration . . . . . . . . . . . . . . . . . . . . . . . . 10 1.2.2 Runtime Reconfiguration (RTR) . . . . . . . . . . . . . . . . . . . 10 1.2.3 Multi-Context Configuration . . . . . . . . . . . . . . . . . . . . . 11 1.2.4 Fine-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2.5 Coarse-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.3 Reconfigurable Computing Specific Design Issues . . . . . . . . . . . . 12 1.4 Overview of this Dissertation . . . . . . . . . . . . . . . . . . . . . . . . . 14 2 Reconfigurable Computing Systems – Background 17 2.1 Examples for RSOCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2 Partially Reconfigurable FPGAs: Xilinx Virtex Device Family . . . . . . 20 2.2.1 Virtex-II/Virtex-II Pro Logic Architecture . . . . . . . . . . . . . 20 2.2.2 Reconfiguration Architecture and Reconfiguration Control . . 21 2.3 Methods for Design Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.3.1 Behavioural Design Entry . . . . . . . . . . . . . . . . . . . . . . . 25 2.3.2 Design Entry at Register-Transfer Level (RTL) . . . . . . . . . . 25 2.3.3 Xilinx Early Access Partial Reconfiguration Design Flow . . . . 26 2.4 Task Management in Reconfigurable Computing . . . . . . . . . . . . . 27 2.4.1 Online and Offline Task Management . . . . . . . . . . . . . . . 28 2.4.2 Task Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.3 Task Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.4.4 Reconfiguration Runtime Overhead . . . . . . . . . . . . . . . . 31 2.5 Configuration Data Compression . . . . . . . . . . . . . . . . . . . . . . . 32 2.6 Evaluation of Reconfigurable Systems . . . . . . . . . . . . . . . . . . . . 35 2.6.1 Energy Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . 35 2.6.2 Area Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . . 37 2.6.3 Runtime Efficiency Models . . . . . . . . . . . . . . . . . . . . . . 37 2.7 Similarity Based Reduction of Reconfiguration Overhead . . . . . . . . 38 2.7.1 Configuration Data Generation Methods . . . . . . . . . . . . . 39 2.7.2 Device Mapping Methods . . . . . . . . . . . . . . . . . . . . . . . 40 2.7.3 Circuit Design Methods . . . . . . . . . . . . . . . . . . . . . . . . 41 2.7.4 Model for Partial Configuration . . . . . . . . . . . . . . . . . . . 44 2.8 Contributions of this Work . . . . . . . . . . . . . . . . . . . . . . . . . . 44 3 Runtime Reconfiguration Cost and Optimization Methods 47 3.1 Motivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 3.2 Reconfiguration State Graph . . . . . . . . . . . . . . . . . . . . . . . . . 50 3.2.1 Reconfiguration Time Overhead . . . . . . . . . . . . . . . . . . 52 3.2.2 Dynamic Configuration Data Overhead . . . . . . . . . . . . . . 52 3.3 Configuration Cost at Bitstream Level . . . . . . . . . . . . . . . . . . . . 54 3.4 Configuration Cost at Structural Level . . . . . . . . . . . . . . . . . . . 56 3.4.1 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 3.4.2 Virtual Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . 62 3.4.3 Reconfiguration Costs in the VA Context . . . . . . . . . . . . . 65 3.5 Allocation Functions with Minimal Reconfiguration Costs . . . . . . . 67 3.5.1 Allocation of Node Pairs . . . . . . . . . . . . . . . . . . . . . . . 68 3.5.2 Direct Allocation of Nodes . . . . . . . . . . . . . . . . . . . . . . 76 3.5.3 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 3.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 4 Implementation Tools for Reconfigurable Computing 95 4.1 Mapping of Netlists to FPGA Resources . . . . . . . . . . . . . . . . . . . 96 4.1.1 Mapping to Device Resources . . . . . . . . . . . . . . . . . . . . 96 4.1.2 Connectivity Transformations . . . . . . . . . . . . . . . . . . . . 99 4.1.3 Mapping Variants and Reconfiguration Costs . . . . . . . . . . . 100 4.1.4 Mapping of Circuit Macros . . . . . . . . . . . . . . . . . . . . . . 101 4.1.5 Global Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . . 102 4.1.6 Netlist Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2 Mapping Aware Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2.1 Generalized Node Mapping . . . . . . . . . . . . . . . . . . . . . 104 4.2.2 Successive Node Allocation . . . . . . . . . . . . . . . . . . . . . 105 4.2.3 Node Allocation with Ant Colony Optimization . . . . . . . . . 107 4.2.4 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3 Netlist Mapping with Minimized Reconfiguration Cost . . . . . . . . . 110 4.3.1 Mapping Database . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 4.3.2 Mapping and Packing of Elements into Logic Blocks . . . . . . 112 4.3.3 Logic Element Selection . . . . . . . . . . . . . . . . . . . . . . . 114 4.3.4 Logic Element Selection for Min. Routing Reconfiguration . . 115 4.3.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 5 High-Level Synthesis for Reconfigurable Computing 125 5.1 Introduction to HLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.1 HLS Tool Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.2 Realization of the Hardware Tasks . . . . . . . . . . . . . . . . . 128 5.2 New Concepts for Task-based Reconfiguration . . . . . . . . . . . . . . 131 5.2.1 Multiple Hardware Tasks in one Reconfigurable Module . . . . 132 5.2.2 Multi-Level Reconfiguration . . . . . . . . . . . . . . . . . . . . . 133 5.2.3 Resource Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.3 Datapath Synthesis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.1 Task Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.2 Resource Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.3 Resource Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.4 Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 5.3.5 Constraints for Scheduling and Resource Binding . . . . . . . . 151 5.4 Reconfiguration Optimized Datapath Implementation . . . . . . . . . . 153 5.4.1 Effects of Scheduling and Binding on Reconfiguration Costs . 153 5.4.2 Strategies for Resource Type Binding . . . . . . . . . . . . . . . 154 5.4.3 Strategies for Resource Instance Binding . . . . . . . . . . . . . 157 5.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 5.5.1 Summary of Binding Methods and Tool Setup . . . . . . . . . . 163 5.5.2 Cost Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 5.5.3 Implementation Scenarios . . . . . . . . . . . . . . . . . . . . . . 166 5.5.4 Benchmark Characteristics . . . . . . . . . . . . . . . . . . . . . . 168 5.5.5 Benchmark Results . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 5.5.6 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 5.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6 Summary and Outlook 185 Bibliography 189 A Simulated Annealing 201Partielle dynamische Rekonfiguration von FPGAs hat in den letzten Jahren große Aufmerksamkeit von Wissenschaft und Industrie auf sich gezogen. Die Technik erlaubt es, die Funktionalität von progammierbaren Bausteinen zur Laufzeit an veränderte Anforderungen anzupassen. Dynamische Rekonfiguration erlaubt es Entwicklern, FPGAs effizienter einzusetzen: z.B. können Ressourcen für verschiedene Funktionen wiederverwendet werden und die Funktionen selbst können zur Laufzeit an veränderte Verarbeitungsschritte angepasst werden. Insgesamt erlaubt partielle dynamische Rekonfiguration eine einzigartige Kombination von software-artiger Flexibilität und hardware-artiger Leistungsfähigkeit. Bis heute gibt es keine Übereinkunft darüber, wie der zusätzliche Aufwand, der durch partielle dynamische Rekonfiguration verursacht wird, zu bewerten ist. Diese Dissertation führt ein neues Kostenmodell für Laufzeit und Speicherbedarf ein, welche durch partielle dynamische Rekonfiguration verursacht wird. Es wird aufgezeigt, wie das Modell in alle Ebenen der Entwurfsoptimierung für rekonfigurierbare Hardware einbezogen werden kann. Insbesondere wird gezeigt, wie digitale Schaltungen derart auf FPGAs abgebildet werden können, sodass nur wenig Ressourcen der Hardware zur Laufzeit rekonfiguriert werden müssen. Dadurch kann Zeit, Speicher und Energie eingespart werden. Die Entwurfsoptimierung ist am effektivsten, wenn sie auf der Ebene der High-Level-Synthese angewendet wird. Diese Arbeit beschreibt, wie das Kostenmodell in ein neuartiges Werkzeug für die High-Level-Synthese integriert wurde. Das Werkzeug erlaubt es, beim Entwurf die Nutzung von FPGA-Ressourcen gegen den Rekonfigurationsaufwand abzuwägen. Es wird gezeigt, dass partielle Rekonfiguration nur wenig Kosten verursacht, wenn der Entwurf bezüglich Rekonfigurationskosten optimiert wird. Eine Anzahl von Beispielen und experimentellen Ergebnissen belegt die Vorteile der angewendeten Methodik.:1 Introduction 1 1.1 Reconfigurable Computing . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1.1 Reconfigurable System on a Chip (RSOC) . . . . . . . . . . . . 4 1.1.2 Anatomy of an Application . . . . . . . . . . . . . . . . . . . . . . 6 1.1.3 RSOC Design Characteristics and Trade-offs . . . . . . . . . . . 7 1.2 Classification of Reconfigurable Architectures . . . . . . . . . . . . . . . 10 1.2.1 Partial Reconfiguration . . . . . . . . . . . . . . . . . . . . . . . . 10 1.2.2 Runtime Reconfiguration (RTR) . . . . . . . . . . . . . . . . . . . 10 1.2.3 Multi-Context Configuration . . . . . . . . . . . . . . . . . . . . . 11 1.2.4 Fine-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2.5 Coarse-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.3 Reconfigurable Computing Specific Design Issues . . . . . . . . . . . . 12 1.4 Overview of this Dissertation . . . . . . . . . . . . . . . . . . . . . . . . . 14 2 Reconfigurable Computing Systems – Background 17 2.1 Examples for RSOCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2 Partially Reconfigurable FPGAs: Xilinx Virtex Device Family . . . . . . 20 2.2.1 Virtex-II/Virtex-II Pro Logic Architecture . . . . . . . . . . . . . 20 2.2.2 Reconfiguration Architecture and Reconfiguration Control . . 21 2.3 Methods for Design Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.3.1 Behavioural Design Entry . . . . . . . . . . . . . . . . . . . . . . . 25 2.3.2 Design Entry at Register-Transfer Level (RTL) . . . . . . . . . . 25 2.3.3 Xilinx Early Access Partial Reconfiguration Design Flow . . . . 26 2.4 Task Management in Reconfigurable Computing . . . . . . . . . . . . . 27 2.4.1 Online and Offline Task Management . . . . . . . . . . . . . . . 28 2.4.2 Task Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.3 Task Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.4.4 Reconfiguration Runtime Overhead . . . . . . . . . . . . . . . . 31 2.5 Configuration Data Compression . . . . . . . . . . . . . . . . . . . . . . . 32 2.6 Evaluation of Reconfigurable Systems . . . . . . . . . . . . . . . . . . . . 35 2.6.1 Energy Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . 35 2.6.2 Area Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . . 37 2.6.3 Runtime Efficiency Models . . . . . . . . . . . . . . . . . . . . . . 37 2.7 Similarity Based Reduction of Reconfiguration Overhead . . . . . . . . 38 2.7.1 Configuration Data Generation Methods . . . . . . . . . . . . . 39 2.7.2 Device Mapping Methods . . . . . . . . . . . . . . . . . . . . . . . 40 2.7.3 Circuit Design Methods . . . . . . . . . . . . . . . . . . . . . . . . 41 2.7.4 Model for Partial Configuration . . . . . . . . . . . . . . . . . . . 44 2.8 Contributions of this Work . . . . . . . . . . . . . . . . . . . . . . . . . . 44 3 Runtime Reconfiguration Cost and Optimization Methods 47 3.1 Motivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 3.2 Reconfiguration State Graph . . . . . . . . . . . . . . . . . . . . . . . . . 50 3.2.1 Reconfiguration Time Overhead . . . . . . . . . . . . . . . . . . 52 3.2.2 Dynamic Configuration Data Overhead . . . . . . . . . . . . . . 52 3.3 Configuration Cost at Bitstream Level . . . . . . . . . . . . . . . . . . . . 54 3.4 Configuration Cost at Structural Level . . . . . . . . . . . . . . . . . . . 56 3.4.1 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 3.4.2 Virtual Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . 62 3.4.3 Reconfiguration Costs in the VA Context . . . . . . . . . . . . . 65 3.5 Allocation Functions with Minimal Reconfiguration Costs . . . . . . . 67 3.5.1 Allocation of Node Pairs . . . . . . . . . . . . . . . . . . . . . . . 68 3.5.2 Direct Allocation of Nodes . . . . . . . . . . . . . . . . . . . . . . 76 3.5.3 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 3.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 4 Implementation Tools for Reconfigurable Computing 95 4.1 Mapping of Netlists to FPGA Resources . . . . . . . . . . . . . . . . . . . 96 4.1.1 Mapping to Device Resources . . . . . . . . . . . . . . . . . . . . 96 4.1.2 Connectivity Transformations . . . . . . . . . . . . . . . . . . . . 99 4.1.3 Mapping Variants and Reconfiguration Costs . . . . . . . . . . . 100 4.1.4 Mapping of Circuit Macros . . . . . . . . . . . . . . . . . . . . . . 101 4.1.5 Global Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . . 102 4.1.6 Netlist Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2 Mapping Aware Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2.1 Generalized Node Mapping . . . . . . . . . . . . . . . . . . . . . 104 4.2.2 Successive Node Allocation . . . . . . . . . . . . . . . . . . . . . 105 4.2.3 Node Allocation with Ant Colony Optimization . . . . . . . . . 107 4.2.4 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3 Netlist Mapping with Minimized Reconfiguration Cost . . . . . . . . . 110 4.3.1 Mapping Database . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 4.3.2 Mapping and Packing of Elements into Logic Blocks . . . . . . 112 4.3.3 Logic Element Selection . . . . . . . . . . . . . . . . . . . . . . . 114 4.3.4 Logic Element Selection for Min. Routing Reconfiguration . . 115 4.3.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 5 High-Level Synthesis for Reconfigurable Computing 125 5.1 Introduction to HLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.1 HLS Tool Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.2 Realization of the Hardware Tasks . . . . . . . . . . . . . . . . . 128 5.2 New Concepts for Task-based Reconfiguration . . . . . . . . . . . . . . 131 5.2.1 Multiple Hardware Tasks in one Reconfigurable Module . . . . 132 5.2.2 Multi-Level Reconfiguration . . . . . . . . . . . . . . . . . . . . . 133 5.2.3 Resource Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.3 Datapath Synthesis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.1 Task Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.2 Resource Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.3 Resource Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.4 Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 5.3.5 Constraints for Scheduling and Resource Binding . . . . . . . . 151 5.4 Reconfiguration Optimized Datapath Implementation . . . . . . . . . . 153 5.4.1 Effects of Scheduling and Binding on Reconfiguration Costs . 153 5.4.2 Strategies for Resource Type Binding . . . . . . . . . . . . . . . 154 5.4.3 Strategies for Resource Instance Binding . . . . . . . . . . . . . 157 5.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 5.5.1 Summary of Binding Methods and Tool Setup . . . . . . . . . . 163 5.5.2 Cost Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 5.5.3 Implementation Scenarios . . . . . . . . . . . . . . . . . . . . . . 166 5.5.4 Benchmark Characteristics . . . . . . . . . . . . . . . . . . . . . . 168 5.5.5 Benchmark Results . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 5.5.6 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 5.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6 Summary and Outlook 185 Bibliography 189 A Simulated Annealing 20

Models, Design Methods and Tools for Improved Partial Dynamic Reconfiguration

Partial dynamic reconfiguration of FPGAs has attracted high attention from both academia and industry in recent years. With this technique, the functionality of the programmable devices can be adapted at runtime to changing requirements. The approach allows designers to use FPGAs more efficiently: E. g. FPGA resources can be time-shared between different functions and the functions itself can be adapted to changing workloads at runtime. Thus partial dynamic reconfiguration enables a unique combination of software-like flexibility and hardware-like performance. Still there exists no common understanding on how to assess the overhead introduced by partial dynamic reconfiguration. This dissertation presents a new cost model for both the runtime and the memory overhead that results from partial dynamic reconfiguration. It is shown how the model can be incorporated into all stages of the design optimization for reconfigurable hardware. In particular digital circuits can be mapped onto FPGAs such that only small fractions of the hardware must be reconfigured at runtime, which saves time, memory, and energy. The design optimization is most efficient if it is applied during high level synthesis. This book describes how the cost model has been integrated into a new high level synthesis tool. The tool allows the designer to trade-off FPGA resource use versus reconfiguration overhead. It is shown that partial reconfiguration causes only small overhead if the design is optimized with regard to reconfiguration cost. A wide range of experimental results is provided that demonstrates the benefits of the applied method.:1 Introduction 1 1.1 Reconfigurable Computing . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1.1 Reconfigurable System on a Chip (RSOC) . . . . . . . . . . . . 4 1.1.2 Anatomy of an Application . . . . . . . . . . . . . . . . . . . . . . 6 1.1.3 RSOC Design Characteristics and Trade-offs . . . . . . . . . . . 7 1.2 Classification of Reconfigurable Architectures . . . . . . . . . . . . . . . 10 1.2.1 Partial Reconfiguration . . . . . . . . . . . . . . . . . . . . . . . . 10 1.2.2 Runtime Reconfiguration (RTR) . . . . . . . . . . . . . . . . . . . 10 1.2.3 Multi-Context Configuration . . . . . . . . . . . . . . . . . . . . . 11 1.2.4 Fine-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2.5 Coarse-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.3 Reconfigurable Computing Specific Design Issues . . . . . . . . . . . . 12 1.4 Overview of this Dissertation . . . . . . . . . . . . . . . . . . . . . . . . . 14 2 Reconfigurable Computing Systems – Background 17 2.1 Examples for RSOCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2 Partially Reconfigurable FPGAs: Xilinx Virtex Device Family . . . . . . 20 2.2.1 Virtex-II/Virtex-II Pro Logic Architecture . . . . . . . . . . . . . 20 2.2.2 Reconfiguration Architecture and Reconfiguration Control . . 21 2.3 Methods for Design Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.3.1 Behavioural Design Entry . . . . . . . . . . . . . . . . . . . . . . . 25 2.3.2 Design Entry at Register-Transfer Level (RTL) . . . . . . . . . . 25 2.3.3 Xilinx Early Access Partial Reconfiguration Design Flow . . . . 26 2.4 Task Management in Reconfigurable Computing . . . . . . . . . . . . . 27 2.4.1 Online and Offline Task Management . . . . . . . . . . . . . . . 28 2.4.2 Task Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.3 Task Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.4.4 Reconfiguration Runtime Overhead . . . . . . . . . . . . . . . . 31 2.5 Configuration Data Compression . . . . . . . . . . . . . . . . . . . . . . . 32 2.6 Evaluation of Reconfigurable Systems . . . . . . . . . . . . . . . . . . . . 35 2.6.1 Energy Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . 35 2.6.2 Area Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . . 37 2.6.3 Runtime Efficiency Models . . . . . . . . . . . . . . . . . . . . . . 37 2.7 Similarity Based Reduction of Reconfiguration Overhead . . . . . . . . 38 2.7.1 Configuration Data Generation Methods . . . . . . . . . . . . . 39 2.7.2 Device Mapping Methods . . . . . . . . . . . . . . . . . . . . . . . 40 2.7.3 Circuit Design Methods . . . . . . . . . . . . . . . . . . . . . . . . 41 2.7.4 Model for Partial Configuration . . . . . . . . . . . . . . . . . . . 44 2.8 Contributions of this Work . . . . . . . . . . . . . . . . . . . . . . . . . . 44 3 Runtime Reconfiguration Cost and Optimization Methods 47 3.1 Motivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 3.2 Reconfiguration State Graph . . . . . . . . . . . . . . . . . . . . . . . . . 50 3.2.1 Reconfiguration Time Overhead . . . . . . . . . . . . . . . . . . 52 3.2.2 Dynamic Configuration Data Overhead . . . . . . . . . . . . . . 52 3.3 Configuration Cost at Bitstream Level . . . . . . . . . . . . . . . . . . . . 54 3.4 Configuration Cost at Structural Level . . . . . . . . . . . . . . . . . . . 56 3.4.1 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 3.4.2 Virtual Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . 62 3.4.3 Reconfiguration Costs in the VA Context . . . . . . . . . . . . . 65 3.5 Allocation Functions with Minimal Reconfiguration Costs . . . . . . . 67 3.5.1 Allocation of Node Pairs . . . . . . . . . . . . . . . . . . . . . . . 68 3.5.2 Direct Allocation of Nodes . . . . . . . . . . . . . . . . . . . . . . 76 3.5.3 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 3.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 4 Implementation Tools for Reconfigurable Computing 95 4.1 Mapping of Netlists to FPGA Resources . . . . . . . . . . . . . . . . . . . 96 4.1.1 Mapping to Device Resources . . . . . . . . . . . . . . . . . . . . 96 4.1.2 Connectivity Transformations . . . . . . . . . . . . . . . . . . . . 99 4.1.3 Mapping Variants and Reconfiguration Costs . . . . . . . . . . . 100 4.1.4 Mapping of Circuit Macros . . . . . . . . . . . . . . . . . . . . . . 101 4.1.5 Global Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . . 102 4.1.6 Netlist Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2 Mapping Aware Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2.1 Generalized Node Mapping . . . . . . . . . . . . . . . . . . . . . 104 4.2.2 Successive Node Allocation . . . . . . . . . . . . . . . . . . . . . 105 4.2.3 Node Allocation with Ant Colony Optimization . . . . . . . . . 107 4.2.4 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3 Netlist Mapping with Minimized Reconfiguration Cost . . . . . . . . . 110 4.3.1 Mapping Database . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 4.3.2 Mapping and Packing of Elements into Logic Blocks . . . . . . 112 4.3.3 Logic Element Selection . . . . . . . . . . . . . . . . . . . . . . . 114 4.3.4 Logic Element Selection for Min. Routing Reconfiguration . . 115 4.3.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 5 High-Level Synthesis for Reconfigurable Computing 125 5.1 Introduction to HLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.1 HLS Tool Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.2 Realization of the Hardware Tasks . . . . . . . . . . . . . . . . . 128 5.2 New Concepts for Task-based Reconfiguration . . . . . . . . . . . . . . 131 5.2.1 Multiple Hardware Tasks in one Reconfigurable Module . . . . 132 5.2.2 Multi-Level Reconfiguration . . . . . . . . . . . . . . . . . . . . . 133 5.2.3 Resource Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.3 Datapath Synthesis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.1 Task Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.2 Resource Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.3 Resource Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.4 Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 5.3.5 Constraints for Scheduling and Resource Binding . . . . . . . . 151 5.4 Reconfiguration Optimized Datapath Implementation . . . . . . . . . . 153 5.4.1 Effects of Scheduling and Binding on Reconfiguration Costs . 153 5.4.2 Strategies for Resource Type Binding . . . . . . . . . . . . . . . 154 5.4.3 Strategies for Resource Instance Binding . . . . . . . . . . . . . 157 5.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 5.5.1 Summary of Binding Methods and Tool Setup . . . . . . . . . . 163 5.5.2 Cost Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 5.5.3 Implementation Scenarios . . . . . . . . . . . . . . . . . . . . . . 166 5.5.4 Benchmark Characteristics . . . . . . . . . . . . . . . . . . . . . . 168 5.5.5 Benchmark Results . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 5.5.6 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 5.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6 Summary and Outlook 185 Bibliography 189 A Simulated Annealing 201Partielle dynamische Rekonfiguration von FPGAs hat in den letzten Jahren große Aufmerksamkeit von Wissenschaft und Industrie auf sich gezogen. Die Technik erlaubt es, die Funktionalität von progammierbaren Bausteinen zur Laufzeit an veränderte Anforderungen anzupassen. Dynamische Rekonfiguration erlaubt es Entwicklern, FPGAs effizienter einzusetzen: z.B. können Ressourcen für verschiedene Funktionen wiederverwendet werden und die Funktionen selbst können zur Laufzeit an veränderte Verarbeitungsschritte angepasst werden. Insgesamt erlaubt partielle dynamische Rekonfiguration eine einzigartige Kombination von software-artiger Flexibilität und hardware-artiger Leistungsfähigkeit. Bis heute gibt es keine Übereinkunft darüber, wie der zusätzliche Aufwand, der durch partielle dynamische Rekonfiguration verursacht wird, zu bewerten ist. Diese Dissertation führt ein neues Kostenmodell für Laufzeit und Speicherbedarf ein, welche durch partielle dynamische Rekonfiguration verursacht wird. Es wird aufgezeigt, wie das Modell in alle Ebenen der Entwurfsoptimierung für rekonfigurierbare Hardware einbezogen werden kann. Insbesondere wird gezeigt, wie digitale Schaltungen derart auf FPGAs abgebildet werden können, sodass nur wenig Ressourcen der Hardware zur Laufzeit rekonfiguriert werden müssen. Dadurch kann Zeit, Speicher und Energie eingespart werden. Die Entwurfsoptimierung ist am effektivsten, wenn sie auf der Ebene der High-Level-Synthese angewendet wird. Diese Arbeit beschreibt, wie das Kostenmodell in ein neuartiges Werkzeug für die High-Level-Synthese integriert wurde. Das Werkzeug erlaubt es, beim Entwurf die Nutzung von FPGA-Ressourcen gegen den Rekonfigurationsaufwand abzuwägen. Es wird gezeigt, dass partielle Rekonfiguration nur wenig Kosten verursacht, wenn der Entwurf bezüglich Rekonfigurationskosten optimiert wird. Eine Anzahl von Beispielen und experimentellen Ergebnissen belegt die Vorteile der angewendeten Methodik.:1 Introduction 1 1.1 Reconfigurable Computing . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1.1 Reconfigurable System on a Chip (RSOC) . . . . . . . . . . . . 4 1.1.2 Anatomy of an Application . . . . . . . . . . . . . . . . . . . . . . 6 1.1.3 RSOC Design Characteristics and Trade-offs . . . . . . . . . . . 7 1.2 Classification of Reconfigurable Architectures . . . . . . . . . . . . . . . 10 1.2.1 Partial Reconfiguration . . . . . . . . . . . . . . . . . . . . . . . . 10 1.2.2 Runtime Reconfiguration (RTR) . . . . . . . . . . . . . . . . . . . 10 1.2.3 Multi-Context Configuration . . . . . . . . . . . . . . . . . . . . . 11 1.2.4 Fine-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2.5 Coarse-Grain Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.3 Reconfigurable Computing Specific Design Issues . . . . . . . . . . . . 12 1.4 Overview of this Dissertation . . . . . . . . . . . . . . . . . . . . . . . . . 14 2 Reconfigurable Computing Systems – Background 17 2.1 Examples for RSOCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2 Partially Reconfigurable FPGAs: Xilinx Virtex Device Family . . . . . . 20 2.2.1 Virtex-II/Virtex-II Pro Logic Architecture . . . . . . . . . . . . . 20 2.2.2 Reconfiguration Architecture and Reconfiguration Control . . 21 2.3 Methods for Design Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2.3.1 Behavioural Design Entry . . . . . . . . . . . . . . . . . . . . . . . 25 2.3.2 Design Entry at Register-Transfer Level (RTL) . . . . . . . . . . 25 2.3.3 Xilinx Early Access Partial Reconfiguration Design Flow . . . . 26 2.4 Task Management in Reconfigurable Computing . . . . . . . . . . . . . 27 2.4.1 Online and Offline Task Management . . . . . . . . . . . . . . . 28 2.4.2 Task Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.4.3 Task Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 2.4.4 Reconfiguration Runtime Overhead . . . . . . . . . . . . . . . . 31 2.5 Configuration Data Compression . . . . . . . . . . . . . . . . . . . . . . . 32 2.6 Evaluation of Reconfigurable Systems . . . . . . . . . . . . . . . . . . . . 35 2.6.1 Energy Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . 35 2.6.2 Area Efficiency Models . . . . . . . . . . . . . . . . . . . . . . . . 37 2.6.3 Runtime Efficiency Models . . . . . . . . . . . . . . . . . . . . . . 37 2.7 Similarity Based Reduction of Reconfiguration Overhead . . . . . . . . 38 2.7.1 Configuration Data Generation Methods . . . . . . . . . . . . . 39 2.7.2 Device Mapping Methods . . . . . . . . . . . . . . . . . . . . . . . 40 2.7.3 Circuit Design Methods . . . . . . . . . . . . . . . . . . . . . . . . 41 2.7.4 Model for Partial Configuration . . . . . . . . . . . . . . . . . . . 44 2.8 Contributions of this Work . . . . . . . . . . . . . . . . . . . . . . . . . . 44 3 Runtime Reconfiguration Cost and Optimization Methods 47 3.1 Motivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 3.2 Reconfiguration State Graph . . . . . . . . . . . . . . . . . . . . . . . . . 50 3.2.1 Reconfiguration Time Overhead . . . . . . . . . . . . . . . . . . 52 3.2.2 Dynamic Configuration Data Overhead . . . . . . . . . . . . . . 52 3.3 Configuration Cost at Bitstream Level . . . . . . . . . . . . . . . . . . . . 54 3.4 Configuration Cost at Structural Level . . . . . . . . . . . . . . . . . . . 56 3.4.1 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 3.4.2 Virtual Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . 62 3.4.3 Reconfiguration Costs in the VA Context . . . . . . . . . . . . . 65 3.5 Allocation Functions with Minimal Reconfiguration Costs . . . . . . . 67 3.5.1 Allocation of Node Pairs . . . . . . . . . . . . . . . . . . . . . . . 68 3.5.2 Direct Allocation of Nodes . . . . . . . . . . . . . . . . . . . . . . 76 3.5.3 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 3.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 4 Implementation Tools for Reconfigurable Computing 95 4.1 Mapping of Netlists to FPGA Resources . . . . . . . . . . . . . . . . . . . 96 4.1.1 Mapping to Device Resources . . . . . . . . . . . . . . . . . . . . 96 4.1.2 Connectivity Transformations . . . . . . . . . . . . . . . . . . . . 99 4.1.3 Mapping Variants and Reconfiguration Costs . . . . . . . . . . . 100 4.1.4 Mapping of Circuit Macros . . . . . . . . . . . . . . . . . . . . . . 101 4.1.5 Global Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . . 102 4.1.6 Netlist Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2 Mapping Aware Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.2.1 Generalized Node Mapping . . . . . . . . . . . . . . . . . . . . . 104 4.2.2 Successive Node Allocation . . . . . . . . . . . . . . . . . . . . . 105 4.2.3 Node Allocation with Ant Colony Optimization . . . . . . . . . 107 4.2.4 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 4.3 Netlist Mapping with Minimized Reconfiguration Cost . . . . . . . . . 110 4.3.1 Mapping Database . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 4.3.2 Mapping and Packing of Elements into Logic Blocks . . . . . . 112 4.3.3 Logic Element Selection . . . . . . . . . . . . . . . . . . . . . . . 114 4.3.4 Logic Element Selection for Min. Routing Reconfiguration . . 115 4.3.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 4.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 5 High-Level Synthesis for Reconfigurable Computing 125 5.1 Introduction to HLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.1 HLS Tool Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 5.1.2 Realization of the Hardware Tasks . . . . . . . . . . . . . . . . . 128 5.2 New Concepts for Task-based Reconfiguration . . . . . . . . . . . . . . 131 5.2.1 Multiple Hardware Tasks in one Reconfigurable Module . . . . 132 5.2.2 Multi-Level Reconfiguration . . . . . . . . . . . . . . . . . . . . . 133 5.2.3 Resource Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 5.3 Datapath Synthesis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.1 Task Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 5.3.2 Resource Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.3 Resource Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 5.3.4 Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 5.3.5 Constraints for Scheduling and Resource Binding . . . . . . . . 151 5.4 Reconfiguration Optimized Datapath Implementation . . . . . . . . . . 153 5.4.1 Effects of Scheduling and Binding on Reconfiguration Costs . 153 5.4.2 Strategies for Resource Type Binding . . . . . . . . . . . . . . . 154 5.4.3 Strategies for Resource Instance Binding . . . . . . . . . . . . . 157 5.5 Experiments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 5.5.1 Summary of Binding Methods and Tool Setup . . . . . . . . . . 163 5.5.2 Cost Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 5.5.3 Implementation Scenarios . . . . . . . . . . . . . . . . . . . . . . 166 5.5.4 Benchmark Characteristics . . . . . . . . . . . . . . . . . . . . . . 168 5.5.5 Benchmark Results . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 5.5.6 Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 5.6 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6 Summary and Outlook 185 Bibliography 189 A Simulated Annealing 20

Embedded electronic systems driven by run-time reconfigurable hardware

Abstract This doctoral thesis addresses the design of embedded electronic systems based on run-time reconfigurable hardware technology –available through SRAM-based FPGA/SoC devices– aimed at contributing to enhance the life quality of the human beings. This work does research on the conception of the system architecture and the reconfiguration engine that provides to the FPGA the capability of dynamic partial reconfiguration in order to synthesize, by means of hardware/software co-design, a given application partitioned in processing tasks which are multiplexed in time and space, optimizing thus its physical implementation –silicon area, processing time, complexity, flexibility, functional density, cost and power consumption– in comparison with other alternatives based on static hardware (MCU, DSP, GPU, ASSP, ASIC, etc.). The design flow of such technology is evaluated through the prototyping of several engineering applications (control systems, mathematical coprocessors, complex image processors, etc.), showing a high enough level of maturity for its exploitation in the industry.Resumen Esta tesis doctoral abarca el diseño de sistemas electrónicos embebidos basados en tecnología hardware dinámicamente reconfigurable –disponible a través de dispositivos lógicos programables SRAM FPGA/SoC– que contribuyan a la mejora de la calidad de vida de la sociedad. Se investiga la arquitectura del sistema y del motor de reconfiguración que proporcione a la FPGA la capacidad de reconfiguración dinámica parcial de sus recursos programables, con objeto de sintetizar, mediante codiseño hardware/software, una determinada aplicación particionada en tareas multiplexadas en tiempo y en espacio, optimizando así su implementación física –área de silicio, tiempo de procesado, complejidad, flexibilidad, densidad funcional, coste y potencia disipada– comparada con otras alternativas basadas en hardware estático (MCU, DSP, GPU, ASSP, ASIC, etc.). Se evalúa el flujo de diseño de dicha tecnología a través del prototipado de varias aplicaciones de ingeniería (sistemas de control, coprocesadores aritméticos, procesadores de imagen, etc.), evidenciando un nivel de madurez viable ya para su explotación en la industria.Resum Aquesta tesi doctoral està orientada al disseny de sistemes electrònics empotrats basats en tecnologia hardware dinàmicament reconfigurable –disponible mitjançant dispositius lògics programables SRAM FPGA/SoC– que contribueixin a la millora de la qualitat de vida de la societat. S’investiga l’arquitectura del sistema i del motor de reconfiguració que proporcioni a la FPGA la capacitat de reconfiguració dinàmica parcial dels seus recursos programables, amb l’objectiu de sintetitzar, mitjançant codisseny hardware/software, una determinada aplicació particionada en tasques multiplexades en temps i en espai, optimizant així la seva implementació física –àrea de silici, temps de processat, complexitat, flexibilitat, densitat funcional, cost i potència dissipada– comparada amb altres alternatives basades en hardware estàtic (MCU, DSP, GPU, ASSP, ASIC, etc.). S’evalúa el fluxe de disseny d’aquesta tecnologia a través del prototipat de varies aplicacions d’enginyeria (sistemes de control, coprocessadors aritmètics, processadors d’imatge, etc.), demostrant un nivell de maduresa viable ja per a la seva explotació a la indústria

Dynamic partial reconfiguration management for high performance and reliability in FPGAs

Modern Field-Programmable Gate Arrays (FPGAs) are no longer used to implement small “glue logic” circuitries. The high-density of reconfigurable logic resources in today’s FPGAs enable the implementation of large systems in a single chip. FPGAs are highly flexible devices; their functionality can be altered by simply loading a new binary file in their configuration memory. While the flexibility of FPGAs is comparable to General-Purpose Processors (GPPs), in the sense that different functions can be performed using the same hardware, the performance gain that can be achieved using FPGAs can be orders of magnitudes higher as FPGAs offer the ability for customisation of parallel computational architectures. Dynamic Partial Reconfiguration (DPR) allows for changing the functionality of certain blocks on the chip while the rest of the FPGA is operational. DPR has sparked the interest of researchers to explore new computational platforms where computational tasks are off-loaded from a main CPU to be executed using dedicated reconfigurable hardware accelerators configured on demand at run-time. By having a battery of custom accelerators which can be swapped in and out of the FPGA at runtime, a higher computational density can be achieved compared to static systems where the accelerators are bound to fixed locations within the chip. Furthermore, the ability of relocating these accelerators across several locations on the chip allows for the implementation of adaptive systems which can mitigate emerging faults in the FPGA chip when operating in harsh environments. By porting the appropriate fault mitigation techniques in such computational platforms, the advantages of FPGAs can be harnessed in different applications in space and military electronics where FPGAs are usually seen as unreliable devices due to their sensitivity to radiation and extreme environmental conditions. In light of the above, this thesis investigates the deployment of DPR as: 1) a method for enhancing performance by efficient exploitation of the FPGA resources, and 2) a method for enhancing the reliability of systems intended to operate in harsh environments. Achieving optimal performance in such systems requires an efficient internal configuration management system to manage the reconfiguration and execution of the reconfigurable modules in the FPGA. In addition, the system needs to support “fault-resilience” features by integrating parameterisable fault detection and recovery capabilities to meet the reliability standard of fault-tolerant applications. This thesis addresses all the design and implementation aspects of an Internal Configuration Manger (ICM) which supports a novel bitstream relocation model to enable the placement of relocatable accelerators across several locations on the FPGA chip. In addition to supporting all the configuration capabilities required to implement a Reconfigurable Operating System (ROS), the proposed ICM also supports the novel multiple-clone configuration technique which allows for cloning several instances of the same hardware accelerator at the same time resulting in much shorter configuration time compared to traditional configuration techniques. A faulttolerant (FT) version of the proposed ICM which supports a comprehensive faultrecovery scheme is also introduced in this thesis. The proposed FT-ICM is designed with a much smaller area footprint compared to Triple Modular Redundancy (TMR) hardening techniques while keeping a comparable level of fault-resilience. The capabilities of the proposed ICM system are demonstrated with two novel applications. The first application demonstrates a proof-of-concept reliable FPGA server solution used for executing encryption/decryption queries. The proposed server deploys bitstream relocation and modular redundancy to mitigate both permanent and transient faults in the device. It also deploys a novel Built-In Self- Test (BIST) diagnosis scheme, specifically designed to detect emerging permanent faults in the system at run-time. The second application is a data mining application where DPR is used to increase the computational density of a system used to implement the Frequent Itemset Mining (FIM) problem

Методи та засоби підвищення ефективності обробки інформації в реконфігуровних комп’ютерних системах на базі ПЛІС

У дисертації наведено теоретичне узагальнення і нове вирішення наукової проблеми, що полягає в розвитку теорії організації обробки інформації в комп’ютерних системах на ПЛІС з урахуванням їх функціональних та апаратурних обмежень. Запропоновані методи та засоби включають в себе взаємозв’язані вирішення завдань оптимізації процесу обробки інформації шляхом визначення оптимальної зернистості обчислень, а також зменшення накладних витрат процесу відображення задач на реконфігуровне обчислювальне середовище, що в цілому забезпечує підвищення ефективності обробки інформації в реконфігуровних обчислювальних системах на ПЛІС. Запропоновано нову стратегію взаємної адаптації розв’язуваних задач і обчислювального середовища на ПЛІС, що ґрунтується на варіюванні зернистістю обчислень під час розв’язання задач великої розмірності, та вдосконалено концепцію реалізації локальних розподілених засобів керування відображенням задач на реконфігуровне обчислювальне середовище, що підвищує ефективність врахування фізичних параметрів кристалів ПЛІС на всіх рівнях реалізації реконфігуровних комп’ютерних систем