Silicon compilation

Silicon compilation is a term used for many different purposes. In this paper we define silicon compilation as a mapping from some higher level description into layout. We define the basic issues in structural and behavioral silicon compilation and some possible solutions to those issues. Finally, we define the concept of an intelligent silicon compiler in which the compiler evaluates the quality of the generated design and attempts to improve it if it is not satisfactory

Integration of behavioral and layout synthesis : a chip synthesis approach

Chip synthesis deals with the transformation of a behavioral description into a fabricated chip. Typically, chip synthesis is carried out in three stages: behavioral, logic/sequential and layout synthesis. Since chip synthesis involves a multi-level synthesis task, integration and coordination of tasks for all levels of synthesis is the essential issue.This dissertation addresses a chip synthesis paradigm and describes the key issues with regard to the integration of behavioral and layout synthesis for chip design. In order to successfully integrate all tasks in the chip synthesis process, a finite-state machine with a datapath (FSMD) design model and a sliced-layout architecture have been developed for chip synthesis. Using the sliced-layout architecture, a partitioning-based layout synthesis method and system have been developed to synthesize layout from generalized register-transfer (RT) netlists. In addition, based on the FSMD and the sliced-layout architecture, area and timing models are developed for behavioral synthesis. To incorporate layout information into behavioral synthesis, a unified representation is developed for behavioral synthesis. Using the unified representation and layout model, a layout-driven unit-binding approach is presented. Several sets of experiments were performed to validate the proposed approaches including the layout-synthesis method, the layout model and the layout-driven unit-binding task

A system for microarchitecture and logic optimization

This thesis spans two levels of the design process by examining optimization at both the register-transfer level and at the logic level. More specifically, this thesis addresses the following two problems: 1) performing logic synthesis for custom layout rather than the traditional approach that focuses on synthesis for standard cells, and 2) performing optimization for custom layout from register-transfer level netlists. Thus optimization is performed on the microarchitecture design and at a lower level for individual microarchitecture components.First, techniques are introduced for generating gate-level netlists that take advantage of custom layout capabilities. Such techniques include limiting serial/parallel transistor chains, transistor sizes, and capacitive loads in forming complex gates. These considerations have not been incorporated in previous logic synthesis systems.Second, techniques are introduced for improving the microarchitecture structure and using estimates from lower-level optimization tools to guide microarchitecture design optimizations that attempt to meet user specified area and time constraints. These techniques include the capability for mixing layout styles such as custom layout for random-logic components and bit-slicing for regularly structured components. In this manner the entire design, control logic and datapath, can be optimized at the same time. Further, this paper presents a new methodology for microarchitecture-level optimization that greatly reduces the amount of technology-specific knowledge necessary to perform the optimizations

Regular Datapaths on Field-Programmable Gate Arrays

Field-Programmable Gate Arrays (FPGAs) are a recent kind of programmable logic device. They allow the implementation of integrated digital electronic circuits without requiring the complex optical, chemical and mechanical processes used in a conventional chip fabrication. FPGAs can be embedded in traditional system designflows to perform prototyping and emulation tasks. In addition, they also enable novel applications such as configurable computers with hardware dynamically adaptable to a specific problem. The growing chip capacity now allows even the implementation of CPUs and DSPs on single FPGAs. However, current design automation tools trace their roots to times of very limited FPGA sizes, and are primarily optimized for the implementation of random glue logic. The wide datapaths common to CPUs and DSPs are only processed with reduced performance. This thesis presents Structured Design Implementation (SDI), a suite of specialized tools coordinated by a common strategy, which aims to efficiently map even larger regular datapaths to FPGAs. In all steps, regularity is preserved whenever possible, or restored after disruptive operations were required. The circuits are composed from parametrizable modules providing a variety of logical, arithmetical and storage functions. For each module, multiple target FPGA-specific implementation alternatives may be generated in both gatelevel netlist and layout views. A floorplanner based on a genetic algorithm is then used to simultaneously choose an actual implementation from the set of alternatives for each module, and to arrange the selected module implementations in a linear placement. The floorplanning operation optimizes for short routing delays, high routability, and fit into the target FPGA.Field-Programmable Gate-Arrays (FPGAs) sind eine noch junge Art von programmierbaren Logikbausteinen. Sie erlauben die Implementierung von integrierten Digitalschaltungen ohne die komplizierten optischen, chemischen und mechanischen Prozesse, die normalerweise für die Chipfertigung erforderlich sind. FPGAs können im Rahmen konventioneller Entwurfsmethoden zu Emulationszwecken und Prototyp-Aufbauten herangezogen werden. Sie erlauben aber auch völlig neue Anwendungen wie rekonfigurierbare Computer, deren Hardware dynamisch an ein spezielles Problem angepaßt werden kann. Die gewachsene Chip-Kapazität erlaubt nun sogar die Implementierung von CPUs und digitalen Signalprozessoren (DSPs) auf einem einzelnen FPGA. Die Leistungsfähigkeit der entstandenen Schaltungen wird jedoch durch die zur Zeit erhältlichen CAD-Werkzeuge limitiert, da diese noch auf stark beschränkte FPGA-Größen ausgerichtet sind und primär der platzsparenden Verarbeitung unregelmäßiger Logik dienen. Die breiten Datenpfade in Bit-Slice-Struktur, die den Kern vieler CPUs und DSPs darstellen, werden nur suboptimal behandelt. Diese Arbeit stellt Structured Design Implementation (SDI) vor, ein System von spezialisierten CAD-Werkzeugen, die auch größere reguläre Datenpfade effizient auf FPGAs abbilden. In allen Verarbeitungsschritten wird dabei die bestehende Regularität soweit wie möglich erhalten oder nach regularitätsvernichtenden Operationen wiederhergestellt. Zur Schaltungseingabe steht eine Bibliothek von allgemeinen Modulen aus den Bereichen Logik, Arithmetik und Speicherung bereit. Diese können durch Belegung verschiedener Parameter wie Bit-Breiten und Datentypen an aktuelle Anforderungen angepaßt werden

Describing and Simulating Dynamic Reconfiguration in SystemC Exemplified by a Dedicated 3D Collision Detection Hardware

The ongoing trend towards development of parallel software and the increased flexibility of state-of-the-art programmable logic devices are currently converging in the field of reconfigurable hardware. On the other hand there is the traditional hardware market, with its increasingly short development cycles, which is mainly driven by high-level prototyping of products. To enable the design community to conveniently develop reconfigurable architectures in a short time-to-market, this thesis introduces the library ReChannel, which extends SystemC with advanced language constructs for high level reconfiguration modelling. It combines IP reuse and high-level modelling with reconfiguration. The proposed methodology was tested on a hierarchical FPGA-based 3D collision detection accelerator, is also presented. To enable implementation of such a complex algorithm in FPGA logic it had to be implemented using fixed-point arithmetic. Therefore a special method was derived that enables rounding of the used bounding-volumes without incurring the correctness of the non-intersection reports. This guarantees a correct overall result. A bound on the rounding error was derived that gives a measure of the number of false intersection reports, and thus on the run-time. A triangle and a quadrangle intersection test were implemented as the second</p

Intrinsically Evolvable Artificial Neural Networks

Dedicated hardware implementations of neural networks promise to provide faster, lower power operation when compared to software implementations executing on processors. Unfortunately, most custom hardware implementations do not support intrinsic training of these networks on-chip. The training is typically done using offline software simulations and the obtained network is synthesized and targeted to the hardware offline. The FPGA design presented here facilitates on-chip intrinsic training of artificial neural networks. Block-based neural networks (BbNN), the type of artificial neural networks implemented here, are grid-based networks neuron blocks. These networks are trained using genetic algorithms to simultaneously optimize the network structure and the internal synaptic parameters. The design supports online structure and parameter updates, and is an intrinsically evolvable BbNN platform supporting functional-level hardware evolution. Functional-level evolvable hardware (EHW) uses evolutionary algorithms to evolve interconnections and internal parameters of functional modules in reconfigurable computing systems such as FPGAs. Functional modules can be any hardware modules such as multipliers, adders, and trigonometric functions. In the implementation presented, the functional module is a neuron block. The designed platform is suitable for applications in dynamic environments, and can be adapted and retrained online. The online training capability has been demonstrated using a case study. A performance characterization model for RC implementations of BbNNs has also been presented

Application of bit-slice microprocessors to digital correlation in spread spectrum communication systems

This thesis describes the application of commercially available microprocessors and other VLSI devices to high-speed real-time digital correlation in spread spectrum and related communication applications. Spread spectrum communications are a wide-band secure communication system that generate a very broad spectral bandwidth signal that is therefore hard to detect in noise. They are capable of rejecting intentional or unintentional jamming, and are insensitive to the multipath and fading that affects conventional high frequency systems. The bandwidth of spread spectrum systems must be large to obtain a significant performance improvement. This means that the sequence rate must be fast and therefore very fast microprocessors will be required when they are used to perform spread spectrum correlation. Since multiplication cannot be performed efficiently by microprocessors considerable work, since 1974, has been published in the literature which is devoted to minimising the requirement of multiplications in digital correlation and other signal processing algorithms. These fast techniques are investigated and implemented using general-purpose microprocessors. The restricted-bandwidth problem in microprocessor-based digital correlator has been discussed. A new implementation is suggested which uses bit-slice devices to maintain the flexibility of microprocessor-based digital correlation without sacrificing speed. This microprocessor-based system has been found to be efficient in implementing the correlation process at the baseband in the digital domain as well as the post-correlation signal processing- demodulation, detection and tracking, especiaJIy for low rate signals. A charge coupled-device is used to obtain spectral density function. An all-digital technique which is programmable for any binary waveform and can be used for achieving initial acquisition and maintaining synchronisation in spread spectrum communications is described. Many of the practical implementation problems are discussed. The receiver performance, which is measured in terms of the acquisition time and the bit-error rate, is also presented and results are obtained which are close to those predicted in the system simulations

Embedded electronic systems driven by run-time reconfigurable hardware

Abstract This doctoral thesis addresses the design of embedded electronic systems based on run-time reconfigurable hardware technology –available through SRAM-based FPGA/SoC devices– aimed at contributing to enhance the life quality of the human beings. This work does research on the conception of the system architecture and the reconfiguration engine that provides to the FPGA the capability of dynamic partial reconfiguration in order to synthesize, by means of hardware/software co-design, a given application partitioned in processing tasks which are multiplexed in time and space, optimizing thus its physical implementation –silicon area, processing time, complexity, flexibility, functional density, cost and power consumption– in comparison with other alternatives based on static hardware (MCU, DSP, GPU, ASSP, ASIC, etc.). The design flow of such technology is evaluated through the prototyping of several engineering applications (control systems, mathematical coprocessors, complex image processors, etc.), showing a high enough level of maturity for its exploitation in the industry.Resumen Esta tesis doctoral abarca el diseño de sistemas electrónicos embebidos basados en tecnología hardware dinámicamente reconfigurable –disponible a través de dispositivos lógicos programables SRAM FPGA/SoC– que contribuyan a la mejora de la calidad de vida de la sociedad. Se investiga la arquitectura del sistema y del motor de reconfiguración que proporcione a la FPGA la capacidad de reconfiguración dinámica parcial de sus recursos programables, con objeto de sintetizar, mediante codiseño hardware/software, una determinada aplicación particionada en tareas multiplexadas en tiempo y en espacio, optimizando así su implementación física –área de silicio, tiempo de procesado, complejidad, flexibilidad, densidad funcional, coste y potencia disipada– comparada con otras alternativas basadas en hardware estático (MCU, DSP, GPU, ASSP, ASIC, etc.). Se evalúa el flujo de diseño de dicha tecnología a través del prototipado de varias aplicaciones de ingeniería (sistemas de control, coprocesadores aritméticos, procesadores de imagen, etc.), evidenciando un nivel de madurez viable ya para su explotación en la industria.Resum Aquesta tesi doctoral està orientada al disseny de sistemes electrònics empotrats basats en tecnologia hardware dinàmicament reconfigurable –disponible mitjançant dispositius lògics programables SRAM FPGA/SoC– que contribueixin a la millora de la qualitat de vida de la societat. S’investiga l’arquitectura del sistema i del motor de reconfiguració que proporcioni a la FPGA la capacitat de reconfiguració dinàmica parcial dels seus recursos programables, amb l’objectiu de sintetitzar, mitjançant codisseny hardware/software, una determinada aplicació particionada en tasques multiplexades en temps i en espai, optimizant així la seva implementació física –àrea de silici, temps de processat, complexitat, flexibilitat, densitat funcional, cost i potència dissipada– comparada amb altres alternatives basades en hardware estàtic (MCU, DSP, GPU, ASSP, ASIC, etc.). S’evalúa el fluxe de disseny d’aquesta tecnologia a través del prototipat de varies aplicacions d’enginyeria (sistemes de control, coprocessadors aritmètics, processadors d’imatge, etc.), demostrant un nivell de maduresa viable ja per a la seva explotació a la indústria