Radiation Tolerant Electronics, Volume II

Research on radiation tolerant electronics has increased rapidly over the last few years, resulting in many interesting approaches to model radiation effects and design radiation hardened integrated circuits and embedded systems. This research is strongly driven by the growing need for radiation hardened electronics for space applications, high-energy physics experiments such as those on the large hadron collider at CERN, and many terrestrial nuclear applications, including nuclear energy and safety management. With the progressive scaling of integrated circuit technologies and the growing complexity of electronic systems, their ionizing radiation susceptibility has raised many exciting challenges, which are expected to drive research in the coming decade.After the success of the first Special Issue on Radiation Tolerant Electronics, the current Special Issue features thirteen articles highlighting recent breakthroughs in radiation tolerant integrated circuit design, fault tolerance in FPGAs, radiation effects in semiconductor materials and advanced IC technologies and modelling of radiation effects

Single Event Effect Hardening Designs in 65nm CMOS Bulk Technology

Radiation from terrestrial and space environments is a great danger to integrated circuits (ICs). A single particle from a radiation environment strikes semiconductor materials resulting in voltage and current perturbation, where errors are induced. This phenomenon is termed a Single Event Effect (SEE). With the shrinking of transistor size, charge sharing between adjacent devices leads to less effectiveness of current radiation hardening methods. Improving fault-tolerance of storage cells and logic gates in advanced technologies becomes urgent and important. A new Single Event Upset (SEU) tolerant latch is proposed based on a previous hardened Quatro design. Soft error analysis tools are used and results show that the critical charge of the proposed design is approximately 2 times higher than that of the reference design with negligible penalty in area, delay, and power consumption. A test chip containing the proposed flip-flop chains was designed and exposed to alpha particles as well as heavy ions. Radiation experimental results indicate that the soft error rates of the proposed design are greatly reduced when Linear Energy Transfer (LET) is lower than 4, which makes it a suitable candidate for ground-level high reliability applications. To improve radiation tolerance of combinational circuits, two combinational logic gates are proposed. One is a layout-based hardening Cascode Voltage Switch Logic (CVSL) and the other is a fault-tolerant differential dynamic logic. Results from a SEE simulation tool indicate that the proposed CVSL has a higher critical charge, less cross section, and shorter Single Event Transient (SET) pulses when compared with reference designs. Simulation results also reveal that the proposed differential dynamic logic significantly reduces the SEU rate compared to traditional dynamic logic, and has a higher critical charge and shorter SET pulses than reference hardened design

STUDY OF SINGLE-EVENT EFFECTS ON DIGITAL SYSTEMS

Microelectronic devices and systems have been extensively utilized in a variety of radiation environments, ranging from the low-earth orbit to the ground level. A high-energy particle from such an environment may cause voltage/current transients, thereby inducing Single Event Effect (SEE) errors in an Integrated Circuit (IC). Ever since the first SEE error was reported in 1975, this community has made tremendous progress in investigating the mechanisms of SEE and exploring radiation tolerant techniques. However, as the IC technology advances, the existing hardening techniques have been rendered less effective because of the reduced spacing and charge sharing between devices. The Semiconductor Industry Association (SIA) roadmap has identified radiation-induced soft errors as the major threat to the reliable operation of electronic systems in the future. In digital systems, hardening techniques of their core components, such as latches, logic, and clock network, need to be addressed. Two single event tolerant latch designs taking advantage of feedback transistors are presented and evaluated in both single event resilience and overhead. These feedback transistors are turned OFF in the hold mode, thereby yielding a very large resistance. This, in turn, results in a larger feedback delay and higher single event tolerance. On the other hand, these extra transistors are turned ON when the cell is in the write mode. As a result, no significant write delay is introduced. Both designs demonstrate higher upset threshold and lower cross-section when compared to the reference cells. Dynamic logic circuits have intrinsic single event issues in each stage of the operations. The worst case occurs when the output is evaluated logic high, where the pull-up networks are turned OFF. In this case, the circuit fails to recover the output by pulling the output up to the supply rail. A capacitor added to the feedback path increases the node capacitance of the output and the feedback delay, thereby increasing the single event critical charge. Another differential structure that has two differential inputs and outputs eliminates single event upset issues at the expense of an increased number of transistors. Clock networks in advanced technology nodes may cause significant errors in an IC as the devices are more sensitive to single event strikes. Clock mesh is a widely used clocking scheme in a digital system. It was fabricated in a 28nm technology and evaluated through the use of heavy ions and laser irradiation experiments. Superior resistance to radiation strikes was demonstrated during these tests. In addition to mitigating single event issues by using hardened designs, built-in current sensors can be used to detect single event induced currents in the n-well and, if implemented, subsequently execute fault correction actions. These sensors were simulated and fabricated in a 28nm CMOS process. Simulation, as well as, experimental results, substantiates the validity of this sensor design. This manifests itself as an alternative to existing hardening techniques. In conclusion, this work investigates single event effects in digital systems, especially those in deep-submicron or advanced technology nodes. New hardened latch, dynamic logic, clock, and current sensor designs have been presented and evaluated. Through the use of these designs, the single event tolerance of a digital system can be achieved at the expense of varying overhead in terms of area, power, and delay

Radiation Hardened by Design Methodologies for Soft-Error Mitigated Digital Architectures

abstract: Digital architectures for data encryption, processing, clock synthesis, data transfer, etc. are susceptible to radiation induced soft errors due to charge collection in complementary metal oxide semiconductor (CMOS) integrated circuits (ICs). Radiation hardening by design (RHBD) techniques such as double modular redundancy (DMR) and triple modular redundancy (TMR) are used for error detection and correction respectively in such architectures. Multiple node charge collection (MNCC) causes domain crossing errors (DCE) which can render the redundancy ineffectual. This dissertation describes techniques to ensure DCE mitigation with statistical confidence for various designs. Both sequential and combinatorial logic are separated using these custom and computer aided design (CAD) methodologies. Radiation vulnerability and design overhead are studied on VLSI sub-systems including an advanced encryption standard (AES) which is DCE mitigated using module level coarse separation on a 90-nm process with 99.999% DCE mitigation. A radiation hardened microprocessor (HERMES2) is implemented in both 90-nm and 55-nm technologies with an interleaved separation methodology with 99.99% DCE mitigation while achieving 4.9% increased cell density, 28.5 % reduced routing and 5.6% reduced power dissipation over the module fences implementation. A DMR register-file (RF) is implemented in 55 nm process and used in the HERMES2 microprocessor. The RF array custom design and the decoders APR designed are explored with a focus on design cycle time. Quality of results (QOR) is studied from power, performance, area and reliability (PPAR) perspective to ascertain the improvement over other design techniques. A radiation hardened all-digital multiplying pulsed digital delay line (DDL) is designed for double data rate (DDR2/3) applications for data eye centering during high speed off-chip data transfer. The effect of noise, radiation particle strikes and statistical variation on the designed DDL are studied in detail. The design achieves the best in class 22.4 ps peak-to-peak jitter, 100-850 MHz range at 14 pJ/cycle energy consumption. Vulnerability of the non-hardened design is characterized and portions of the redundant DDL are separated in custom and auto-place and route (APR). Thus, a range of designs for mission critical applications are implemented using methodologies proposed in this work and their potential PPAR benefits explored in detail.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Study of Radiation Effects on 28nm UTBB FDSOI Technology

With the evolution of modern Complementary Metal-Oxide-Semiconductor (CMOS) technology, transistor feature size has been scaled down to nanometers. The scaling has resulted in tremendous advantages to the integrated circuits (ICs), such as higher speed, smaller circuit size, and lower operating voltage. However, it also creates some reliability concerns. In particular, small device dimensions and low operating voltages have caused nanoscale ICs to become highly sensitive to operational disturbances, such as signal coupling, supply and substrate noise, and single event effects (SEEs) caused by ionizing particles, like cosmic neutrons and alpha particles. SEEs found in ICs can introduce transient pulses in circuit nodes or data upsets in storage cells. In well-designed ICs, SEEs appear to be the most troublesome in a space environment or at high altitudes in terrestrial environment. Techniques from the manufacturing process level up to the system design level have been developed to mitigate radiation effects. Among them, silicon-on-insulator (SOI) technologies have proven to be an effective approach to reduce single-event effects in ICs. So far, 28nm ultra-thin body and buried oxide (UTBB) Fully Depleted SOI (FDSOI) by STMicroelectronics is one of the most advanced SOI technologies in commercial applications. Its resilience to radiation effects has not been fully explored and it is of prevalent interest in the radiation effects community. Therefore, two test chips, namely ST1 and AR0, were designed and tested to study SEEs in logic circuits fabricated with this technology. The ST1 test chip was designed to evaluate SET pulse widths in logic gates. Three kinds of the on-chip pulse-width measurement detectors, namely the Vernier detector, the Pulse Capture detector and the Pulse Filter detector, were implemented in the ST1 chip. Moreover, a Circuit for Radiation Effects Self-Test (CREST) chain with combinational logic was designed to study both SET and SEU effects. The ST1 chip was tested using a heavy ion irradiation beam source in Radiation Effects Facility (RADEF), Finland. The experiment results showed that the cross-section of the 28nm UTBB-FDSOI technology is two orders lower than its bulk competitors. Laser tests were also applied to this chip to research the pulse distortion effects and the relationship between SET, SEU and the clock frequency. Total Ionizing Dose experiments were carried out at the University of Saskatchewan and European Space Agency with Co-60 gammacell radiation sources. The test results showed the devices implemented in the 28nm UTBB-FDSOI technology can maintain its functionality up to 1 Mrad(Si). In the AR0 chip, we designed five ARM Cortex-M0 cores with different logic protection levels to investigate the performance of approximate logic protecting methods. There are three custom-designed SRAM blocks in the test chip, which can also be used to measure the SEU rate. From the simulation result, we concluded that the approximate logic methodology can protect the digital logic efficiently. This research comprehensively evaluates the radiation effects in the 28nm UTBB-FDSOI technology, which provides the baseline for later radiation-hardened system designs in this technology

A low power and soft error resilience guard-gated Quartro-based flip-flop in 45 nm CMOS technology

Abstract Conventional flip‐flops are more vulnerable to particle strikes in a radiation environment. To overcome this disadvantage, in the literature, many radiation‐hardened flip‐flops (FFs) based on techniques like triple modular redundancy, dual interlocked cell, Quatro and guard‐gated Quatro cell, and so on, are discussed. The flip‐flop realized using radiation hardened by design Quatro cell is named as the improved version of Quatro flip‐flop (IVQFF). Single event upset (SEU) at inverter stages of master/slave and at output are the two drawbacks of IVQFF. This study proposes a guard‐gated Quatro FF (GQFF) using guard‐gated Quatro cell and Muller C‐element. To overcome the SEU at inverter stages of IVQFF, in GQFF, the inverter stages are realized in a parallel fashion. A dual‐input Muller C‐element is connected to the GQFF output stage to mask the SEU and thus maintain the correct output. The proposed GQFF tolerates both single node upset (SNU) and double node upset (DNU). It also achieves low power. To prove the efficacy, GQFF and the existing FFs are implemented in 45 nm Complementary Metal Oxide Semiconductor (CMOS) technology. From the simulation results, it may be noted that the GQFF is 100% immune to SNUs and 50% immune to DNUs

Fully Automated Radiation Hardened by Design Circuit Construction

abstract: A fully automated logic design methodology for radiation hardened by design (RHBD) high speed logic using fine grained triple modular redundancy (TMR) is presented. The hardening techniques used in the cell library are described and evaluated, with a focus on both layout techniques that mitigate total ionizing dose (TID) and latchup issues and flip-flop designs that mitigate single event transient (SET) and single event upset (SEU) issues. The base TMR self-correcting master-slave flip-flop is described and compared to more traditional hardening techniques. Additional refinements are presented, including testability features that disable the self-correction to allow detection of manufacturing defects. The circuit approach is validated for hardness using both heavy ion and proton broad beam testing. For synthesis and auto place and route, the methodology and circuits leverage commercial logic design automation tools. These tools are glued together with custom CAD tools designed to enable easy conversion of standard single redundant hardware description language (HDL) files into hardened TMR circuitry. The flow allows hardening of any synthesizable logic at clock frequencies comparable to unhardened designs and supports standard low-power techniques, e.g. clock gating and supply voltage scaling.Dissertation/ThesisPh.D. Electrical Engineering 201

Design and Evaluation of Radiation-Hardened Standard Cell Flip-Flops

Use of a standard non-rad-hard digital cell library in the rad-hard design can be a cost-effective solution for space applications. In this paper we demonstrate how a standard non-rad-hard flip-flop, as one of the most vulnerable digital cells, can be converted into a rad-hard flip-flop without modifying its internal structure. We present five variants of a Triple Modular Redundancy (TMR) flip-flop: baseline TMR flip-flop, latch-based TMR flip-flop, True-Single Phase Clock (TSPC) TMR flip-flop, scannable TMR flip-flop and self-correcting TMR flip-flop. For all variants, the multi-bit upsets have been addressed by applying special placement constraints, while the Single Event Transient (SET) mitigation was achieved through the usage of customized SET filters and selection of optimal inverter sizes for the clock and reset trees. The proposed flip-flop variants feature differing performance, thus enabling to choose the optimal solution for every sensitive node in the circuit, according to the predefined design constraints. Several flip-flop designs have been validated on IHP’s 130nm BiCMOS process, by irradiation of custom-designed shift registers. It has been shown that the proposed TMR flip-flops are robust to soft errors with a threshold Linear Energy Transfer (LET) from ( 32.4 (MeV⋅cm2/mg) ) to ( 62.5 (MeV⋅cm2/mg) ), depending on the variant

INVESTIGATING THE EFFECTS OF SINGLE-EVENT UPSETS IN STATIC AND DYNAMIC REGISTERS

Radiation-induced single-event upsets (SEUs) pose a serious threat to the reliability of registers. The existing SEU analyses for static CMOS registers focus on the circuit-level impact and may underestimate the pertinent SEU information provided through node analysis. This thesis proposes SEU node analysis to evaluate the sensitivity of static registers and apply the obtained node information to improve the robustness of the register through selective node hardening (SNH) technique. Unlike previous hardening techniques such as the Triple Modular Redundancy (TMR) and the Dual Interlocked Cell (DICE) latch, the SNH method does not introduce larger area overhead. Moreover, this thesis also explores the impact of SEUs in dynamic flip-flops, which are appealing for the design of high-performance microprocessors. Previous work either uses the approaches for static flip-flops to evaluate SEU effects in dynamic flip-flops or overlook the SEU injected during the precharge phase. In this thesis, possible SEU sensitive nodes in dynamic flip-flops are re-examined and their window of vulnerability (WOV) is extended. Simulation results for SEU analysis in non-hardened dynamic flip-flops reveal that the last 55.3 % of the precharge time and a 100% evaluation time are affected by SEUs

Study of Layout Techniques in Dynamic Logic Circuitry for Single Event Effect Mitigation

Dynamic logic circuits are highly suitable for high-speed applications, considering the fact that they have a smaller area and faster transition. However, their application in space or other radiation-rich environments has been significantly inhibited by their susceptibility to radiation effects. This work begins with the basic operations of dynamic logic circuits, elaborates upon the physics underlying their radiation vulnerability, and evaluates three techniques that harden dynamic logic from the layout: drain extension, pulse quenching, and a proposed method. The drain extension method adds an extra drain to the sensitive node in order to improve charge sharing, the pulse quenching scheme utilizes charge sharing by duplicating a component that offsets the transient pulse, and the proposed technique takes advantage of both. Domino buffers designed using these three techniques, along with a conventional design as reference, were modeled and simulated using a 3D TCAD tool. Simulation results confirm a significant reduction of soft error rate in the proposed technique and suggest a greater reduction with angled incidence. A 130 nm chip containing designed buffer and register chains was fabricated and tested with heavy ion irradiation. According to the experiment results, the proposed design achieved 30% soft error rate reduction, with 19%, 20%, and 10% overhead in speed, power, and area, respectively