688 research outputs found

    Vision-Aided Navigation using Tracked Lankmarks

    Get PDF
    This thesis presents vision-based state estimation algorithms for autonomous vehicles to navigate within GPS-denied environments. To accomplish this objective, an approach is developed that utilizes a priori information about the environment. In particular, the algorithm leverages recognizable ‘landmarks’ in the environment, the positions of which are known in advance, to stabilize the state estimate. Measurements of the position of one or more landmarks in the image plane of a monocular camera are then filtered using an extended Kalman filter (EKF) with data from a traditional inertial measurement unit (IMU) consisting of accelerometers and rate gyros to produce the state estimate. Additionally, the EKF algorithm is adapted to accommodate a stereo camera configuration to measure the distance to a landmark using parallax. The performances of the state estimation algorithms for both the monocular and stereo camera configurations are tested and compared using simulation studies with a quadcopter UAV model. State estimation results are then presented using flight data from a quadcopter UAV instrumented with an IMU and a GoPro camera. It is shown that the proposed landmark navigation method is capable of preventing IMU drift errors by providing a GPS-like measurement when landmarks can be identified. Additionally, the landmark method pairs well with non a priori measurements for interims when landmarks are not available

    Visual 3-D SLAM from UAVs

    Get PDF
    The aim of the paper is to present, test and discuss the implementation of Visual SLAM techniques to images taken from Unmanned Aerial Vehicles (UAVs) outdoors, in partially structured environments. Every issue of the whole process is discussed in order to obtain more accurate localization and mapping from UAVs flights. Firstly, the issues related to the visual features of objects in the scene, their distance to the UAV, and the related image acquisition system and their calibration are evaluated for improving the whole process. Other important, considered issues are related to the image processing techniques, such as interest point detection, the matching procedure and the scaling factor. The whole system has been tested using the COLIBRI mini UAV in partially structured environments. The results that have been obtained for localization, tested against the GPS information of the flights, show that Visual SLAM delivers reliable localization and mapping that makes it suitable for some outdoors applications when flying UAVs

    Review and classification of vision-based localisation techniques in unknown environments

    Get PDF
    International audienceThis study presents a review of the state-of-the-art and a novel classification of current vision-based localisation techniques in unknown environments. Indeed, because of progresses made in computer vision, it is now possible to consider vision-based systems as promising navigation means that can complement traditional navigation sensors like global navigation satellite systems (GNSSs) and inertial navigation systems. This study aims to review techniques employing a camera as a localisation sensor, provide a classification of techniques and introduce schemes that exploit the use of video information within a multi-sensor system. In fact, a general model is needed to better compare existing techniques in order to decide which approach is appropriate and which are the innovation axes. In addition, existing classifications only consider techniques based on vision as a standalone tool and do not consider video as a sensor among others. The focus is addressed to scenarios where no a priori knowledge of the environment is provided. In fact, these scenarios are the most challenging since the system has to cope with objects as they appear in the scene without any prior information about their expected position

    Laser-based geometric modeling using cooperative multiple mobile robots

    Full text link
    Abstract—In order to construct three-dimensional shape models of large-scale architectural structures using a laser range finder, a number of range images are taken from various viewpoints. These images are aligned using post-processing procedures such as the ICP algorithm. However, in general, before applying the ICP algorithm, these range images must be aligned roughly by a human operator in order to converge to precise positions. The present paper proposes a new modeling system using a group of multiple robots and an on-board laser range finder. Each measurement position is identified by a highly precise positioning technique called Cooperative Positioning System (CPS), which utilizes the characteristics of the multiple-robot system. Thus, the proposed system can construct 3D shapes of large-scale architectural structures without any post-processing procedure or manual registration. ICP is applied optionally for a subsequent refinement of the model. Measurement experiments in unknown and large indoor/outdoor environments are carried out successfully using the newly developed measurement system consisting of three mobile robots named CPS-V. Generating a model of Dazaifu Tenmangu, a famous cultural heritage, for its digital archive completes the paper. I

    Map-Based Localization for Unmanned Aerial Vehicle Navigation

    Get PDF
    Unmanned Aerial Vehicles (UAVs) require precise pose estimation when navigating in indoor and GNSS-denied / GNSS-degraded outdoor environments. The possibility of crashing in these environments is high, as spaces are confined, with many moving obstacles. There are many solutions for localization in GNSS-denied environments, and many different technologies are used. Common solutions involve setting up or using existing infrastructure, such as beacons, Wi-Fi, or surveyed targets. These solutions were avoided because the cost should be proportional to the number of users, not the coverage area. Heavy and expensive sensors, for example a high-end IMU, were also avoided. Given these requirements, a camera-based localization solution was selected for the sensor pose estimation. Several camera-based localization approaches were investigated. Map-based localization methods were shown to be the most efficient because they close loops using a pre-existing map, thus the amount of data and the amount of time spent collecting data are reduced as there is no need to re-observe the same areas multiple times. This dissertation proposes a solution to address the task of fully localizing a monocular camera onboard a UAV with respect to a known environment (i.e., it is assumed that a 3D model of the environment is available) for the purpose of navigation for UAVs in structured environments. Incremental map-based localization involves tracking a map through an image sequence. When the map is a 3D model, this task is referred to as model-based tracking. A by-product of the tracker is the relative 3D pose (position and orientation) between the camera and the object being tracked. State-of-the-art solutions advocate that tracking geometry is more robust than tracking image texture because edges are more invariant to changes in object appearance and lighting. However, model-based trackers have been limited to tracking small simple objects in small environments. An assessment was performed in tracking larger, more complex building models, in larger environments. A state-of-the art model-based tracker called ViSP (Visual Servoing Platform) was applied in tracking outdoor and indoor buildings using a UAVs low-cost camera. The assessment revealed weaknesses at large scales. Specifically, ViSP failed when tracking was lost, and needed to be manually re-initialized. Failure occurred when there was a lack of model features in the cameras field of view, and because of rapid camera motion. Experiments revealed that ViSP achieved positional accuracies similar to single point positioning solutions obtained from single-frequency (L1) GPS observations standard deviations around 10 metres. These errors were considered to be large, considering the geometric accuracy of the 3D model used in the experiments was 10 to 40 cm. The first contribution of this dissertation proposes to increase the performance of the localization system by combining ViSP with map-building incremental localization, also referred to as simultaneous localization and mapping (SLAM). Experimental results in both indoor and outdoor environments show sub-metre positional accuracies were achieved, while reducing the number of tracking losses throughout the image sequence. It is shown that by integrating model-based tracking with SLAM, not only does SLAM improve model tracking performance, but the model-based tracker alleviates the computational expense of SLAMs loop closing procedure to improve runtime performance. Experiments also revealed that ViSP was unable to handle occlusions when a complete 3D building model was used, resulting in large errors in its pose estimates. The second contribution of this dissertation is a novel map-based incremental localization algorithm that improves tracking performance, and increases pose estimation accuracies from ViSP. The novelty of this algorithm is the implementation of an efficient matching process that identifies corresponding linear features from the UAVs RGB image data and a large, complex, and untextured 3D model. The proposed model-based tracker improved positional accuracies from 10 m (obtained with ViSP) to 46 cm in outdoor environments, and improved from an unattainable result using VISP to 2 cm positional accuracies in large indoor environments. The main disadvantage of any incremental algorithm is that it requires the camera pose of the first frame. Initialization is often a manual process. The third contribution of this dissertation is a map-based absolute localization algorithm that automatically estimates the camera pose when no prior pose information is available. The method benefits from vertical line matching to accomplish a registration procedure of the reference model views with a set of initial input images via geometric hashing. Results demonstrate that sub-metre positional accuracies were achieved and a proposed enhancement of conventional geometric hashing produced more correct matches - 75% of the correct matches were identified, compared to 11%. Further the number of incorrect matches was reduced by 80%

    Monocular-Based Pose Determination of Uncooperative Space Objects

    Get PDF
    Vision-based methods to determine the relative pose of an uncooperative orbiting object are investigated in applications to spacecraft proximity operations, such as on-orbit servicing, spacecraft formation flying, and small bodies exploration. Depending on whether the object is known or unknown, a shape model of the orbiting target object may have to be constructed autonomously in real-time by making use of only optical measurements. The Simultaneous Estimation of Pose and Shape (SEPS) algorithm that does not require a priori knowledge of the pose and shape of the target is presented. This makes use of a novel measurement equation and filter that can efficiently use optical flow information along with a star tracker to estimate the target's angular rotational and translational relative velocity as well as its center of gravity. Depending on the mission constraints, SEPS can be augmented by a more accurate offline, on-board 3D reconstruction of the target shape, which allows for the estimation of the pose as a known target. The use of Structure from Motion (SfM) for this purpose is discussed. A model-based approach for pose estimation of known targets is also presented. The architecture and implementation of both the proposed approaches are elucidated and their performance metrics are evaluated through numerical simulations by using a dataset of images that are synthetically generated according to a chaser/target relative motion in Geosynchronous Orbit (GEO)

    Non-iterative RGB-D-inertial Odometry

    Full text link
    This paper presents a non-iterative solution to RGB-D-inertial odometry system. Traditional odometry methods resort to iterative algorithms which are usually computationally expensive or require well-designed initialization. To overcome this problem, this paper proposes to combine a non-iterative front-end (odometry) with an iterative back-end (loop closure) for the RGB-D-inertial SLAM system. The main contribution lies in the novel non-iterative front-end, which leverages on inertial fusion and kernel cross-correlators (KCC) to match point clouds in frequency domain. Dominated by the fast Fourier transform (FFT), our method is only of complexity O(nlogn)\mathcal{O}(n\log{n}), where nn is the number of points. Map fusion is conducted by element-wise operations, so that both time and space complexity are further reduced. Extensive experiments show that, due to the lightweight of the proposed front-end, the framework is able to run at a much faster speed yet still with comparable accuracy with the state-of-the-arts

    Single and multiple stereo view navigation for planetary rovers

    Get PDF
    © Cranfield UniversityThis thesis deals with the challenge of autonomous navigation of the ExoMars rover. The absence of global positioning systems (GPS) in space, added to the limitations of wheel odometry makes autonomous navigation based on these two techniques - as done in the literature - an inviable solution and necessitates the use of other approaches. That, among other reasons, motivates this work to use solely visual data to solve the robot’s Egomotion problem. The homogeneity of Mars’ terrain makes the robustness of the low level image processing technique a critical requirement. In the first part of the thesis, novel solutions are presented to tackle this specific problem. Detection of robust features against illumination changes and unique matching and association of features is a sought after capability. A solution for robustness of features against illumination variation is proposed combining Harris corner detection together with moment image representation. Whereas the first provides a technique for efficient feature detection, the moment images add the necessary brightness invariance. Moreover, a bucketing strategy is used to guarantee that features are homogeneously distributed within the images. Then, the addition of local feature descriptors guarantees the unique identification of image cues. In the second part, reliable and precise motion estimation for the Mars’s robot is studied. A number of successful approaches are thoroughly analysed. Visual Simultaneous Localisation And Mapping (VSLAM) is investigated, proposing enhancements and integrating it with the robust feature methodology. Then, linear and nonlinear optimisation techniques are explored. Alternative photogrammetry reprojection concepts are tested. Lastly, data fusion techniques are proposed to deal with the integration of multiple stereo view data. Our robust visual scheme allows good feature repeatability. Because of this, dimensionality reduction of the feature data can be used without compromising the overall performance of the proposed solutions for motion estimation. Also, the developed Egomotion techniques have been extensively validated using both simulated and real data collected at ESA-ESTEC facilities. Multiple stereo view solutions for robot motion estimation are introduced, presenting interesting benefits. The obtained results prove the innovative methods presented here to be accurate and reliable approaches capable to solve the Egomotion problem in a Mars environment
    corecore