Influence of the ratio on the mechanical properties of epoxy resin composite with diapers waste as fillers for partition panel application

Materials play significant role in the domestic economy and defense with the fast growth of science and technology field. New materials are the core of fresh technologies and the three pillars of modern science and technology are materials science, power technology and data science. The prior properties of the partition panel by using recycled diapers waste depend on the origin of waste deposits and its chemical constituents. This study presents the influence of the ratio on the mechanical properties of polymer in diapers waste reinforced with binder matrix for partition panel application. The aim of this study was to investigate the influence of different ratio of diapers waste polymer reinforced epoxy-matrix with regards to mechanical properties and morphology analysis. The polymer includes polypropylene, polystyrene, polyethylene and superabsorbent polymer (SAP) were used as reinforcing material. The tensile and bending resistance for ratio of 0.4 diapers waste polymers indicated the optimum ratio for fabricating the partition panel. Samples with 0.4 ratios of diapers waste polymers have highest stiffness of elasticity reading with 76.06 MPa. A correlation between the micro structural analysis using scanning electron microscope (SEM) and the mechanical properties of the material has been discussed

An agile and adaptive holonic architecture for manufacturing control

Tese de doutoramento. Engenharia Electrotécnica e de Computadores. 2004. Faculdade de Engenharia. Universidade do Port

Plasma sprayed titanium coatings with/without a shroud

Abstract: Titanium coatings were deposited by plasma spraying with and without a shroud. The titanium coatings were then assessed by scanning electron microscopy. A comparison in microstructure between titanium coatings with and without the shroud was carried out. The results showed that the shroud played an important role in protecting the titanium particles from oxidation. The presence of the shroud led to a reduction in coating porosity. The reduction in air entrainment with t he shroud resulted in better heating of the particles, and an enhanced microstructure with lower porosity in the shrouded titanium coatings were observed compared to the air plasma sprayed counterpart

An agile and adaptive holonic architecture for manufacturing control

In the last decades significant changes in the manufacturing environment have been noticed: moving from a local economy towards a global economy, with markets asking for products with high quality at lower costs, highly customised and with short life cycle. In this environment, the manufacturing enterprises, to avoid the risk to lose competitiveness, search to answer more closely to the customer demands, by improving their flexibility and agility, while maintaining their productivity and quality. Actually, the dynamic response to emergence is becoming a key issue, due to the weak response of the traditional manufacturing control systems to unexpected disturbances, mainly because of the rigidity of their control architectures. In these circumstances, the challenge is to develop manufacturing control systems with autonomy and intelligence capabilities, fast adaptation to the environment changes, more robustness against the occurrence of disturbances, and easier integration of manufacturing resources and legacy systems. Several architectures using emergent concepts and technologies have been proposed, in particular those based in the holonic manufacturing paradigm. Holonic manufacturing is a paradigm based in the ideas of the philosopher Arthur Koestler, who proposed the word holon to describe a basic unit of organisation in biological and social systems. A holon, as Koestler devised the term, is an identifiable part of a (manufacturing) system that has a unique identity, yet is made up of sub-ordinate parts and in turn is part of a larger whole. The introduction of the holonic manufacturing paradigm allows a new approach to the manufacturing problem, bringing the advantages of modularity, decentralisation, autonomy, scalability, and re-use of software components. This dissertation intends to develop an agile and adaptive manufacturing control architecture to face the current requirements imposed to the manufacturing enterprises. The architecture proposed in this dissertation addresses the need for the fast reaction to disturbances at the shop floor level, increasing the agility and flexibility of the enterprise, when it works in volatile environments, characterised by the frequent occurrence of unexpected disturbances. The proposed architecture, designated by ADACOR (ADAptive holonic COntrol aRchitecture for distributed manufacturing systems), is based in the holonic manufacturing paradigm, build upon autonomous and cooperative holons, allowing the development of manufacturing control applications that present all the features of decentralised and holonic systems. ADACOR holonic architecture introduces an adaptive control that balances dynamically between a more centralised structure and a more decentralised one, allowing to combine the global production optimisation with agile reaction to unexpected disturbances. Nas últimas décadas têm-se assistido a mudanças significativas no ambiente de fabrico: evoluindo de uma economia local para um economia global, com os mercados a procurar produtos com elevada qualidade a baixos preços, altamente customizados e com um ciclo de vida curto. Neste ambiente, as empresas de manufactura, para evitar o risco de perda de competitividade, procuram responder às solicitações dos clientes, melhorando a sua flexibilidade e agilidade, mantendo os mesmos índices de produtividade e qualidade. Na verdade, a resposta dinâmica à emergência está a tornar-se num assunto chave, devido `a fraca resposta a perturbações que os sistemas de controlo de fabrico tradicionais apresentam, principalmente devido à rigidez das suas arquitecturas de controlo. Nestas circunstâncias, é fundamental o desenvolvimento de sistemas de controlo de fabrico com capacidades de autonomia e inteligência, rápida adaptação às mudanças, maior robustez à ocorrência de perturbações e fácil integração de recursos físicos e sistemas legados. Diversas arquitecturas usando conceitos e tecnologias emergentes têm sido propostas, em particular algumas baseadas no paradigma da produção holónica. O paradigma da produção holónica é inspirado nas ideias de Arthur Koestler, que propôs a palavra holon para descrever uma unidade básica de organização de sistemas biológicos e sociais. Um holon, de acordo com a definição de Koestler, é uma parte identificável do sistema com identidade única, composta por sub-partes e fazendo simultaneamente parte do todo. A introdução do paradigma da produção holónica permite uma nova abordagem aos sistemas de controlo de fabrico, trazendo vantagens de modularidade, descentralização, autonomia, escalabilidade e reutilização de componentes. Esta dissertação pretende desenvolver uma arquitectura de controlo ágil e adaptativa que suporte os requisitos actuais impostos `as empresas de manufactura. A arquitectura proposta visa a necessidade de uma reacção rápida a perturbações, ao nível da planta fabril, melhorando a flexibilidade e agilidade da empresa quando esta opera em ambientes voláteis, caracterizados pela ocorrência frequente de perturbações inesperadas. A arquitectura proposta, designada por ADACOR (ADAptive holonic COntrol aRchitecture for distributed manufacturing systems), é baseada no paradigma da produção holónica e construída sobre holons autónomos e cooperativos, permitindo o desenvolvimento de aplicações de controlo de fabrico que apresentem todas as características dos sistemas descentralizados e holónicos. A arquitectura holónica ADACOR introduz um controlo adaptativo que balança dinamicamente entre uma estrutura de controlo mais centralizada e uma mais descentralizada, permitindo combinar a optimização da produção com a ágil reacção a perturbações

Production Scheduling

Generally speaking, scheduling is the procedure of mapping a set of tasks or jobs (studied objects) to a set of target resources efficiently. More specifically, as a part of a larger planning and scheduling process, production scheduling is essential for the proper functioning of a manufacturing enterprise. This book presents ten chapters divided into five sections. Section 1 discusses rescheduling strategies, policies, and methods for production scheduling. Section 2 presents two chapters about flow shop scheduling. Section 3 describes heuristic and metaheuristic methods for treating the scheduling problem in an efficient manner. In addition, two test cases are presented in Section 4. The first uses simulation, while the second shows a real implementation of a production scheduling system. Finally, Section 5 presents some modeling strategies for building production scheduling systems. This book will be of interest to those working in the decision-making branches of production, in various operational research areas, as well as computational methods design. People from a diverse background ranging from academia and research to those working in industry, can take advantage of this volume

Synthesis of Manufacturing Systems Using Co-Platforming

Modern manufacturing environment is characterized by frequent changes within product design in order to satisfy evolving customer requirements. Various strategies are implemented in order to efficiently manage the consequences arising from the product design changes starting from design of the product, planning, manufacturing…etc. This dissertation focuses mainly on the manufacturing phase in which a new concept in manufacturing system synthesis is proposed. A new concept in manufacturing system synthesis has been introduced and coined as “Co-platforming”. Co-platforming is the synthesis of manufacturing systems through mapping product platform features and components to platform machines on one side, and non-platform product features and components to non-platform machines on the other side, in order to reduce the manufacturing system investment cost and prolong the manufacturing system useful life as product variants evolve and change. Tools and methods are developed to synthesize the manufacturing system based on Co-platforming within functional and physical levels. At the functional level, the group of platform and non-platform machines and the number of each machine type are determined. A new matrix based mapping model is proposed to determine the platform and non-platform machines candidates. A ranking coefficient is formulated which ranks the platform machines according to their machining capabilities in order to assist manufacturing firms in decision making concerning which type of platform machine to choose. Furthermore, a new mathematical programming optimization model is proposed in order to provide the optimum selection of machine types among machine candidates and their numbers. Moreover, a new mathematical programming model is proposed which synthesizes manufacturing systems taking into consideration machine level and system level changes based on co-platforming. At the physical level, the manufacturing system configuration is determined which is concerned with determining the number of stages, types of machines in each stage and the number of machines in each stage. A new mathematical programming optimization model is proposed which determines, in addition to the type and number of each machine, the optimal manufacturing system configuration based on co-platforming. The Co-platforming methodology is being applied in two case studies from automotive industry. The first case study is concerned with machining of automotive cylinder blocks taken from Mitsubishi Heavy Industries and the second case study is concerned with the assembly of automotive cylinder heads taken from ABB flexible automation. The results obtained from the co-platforming methodology indicate that cost reduction can be achieved when synthesizing the manufacturing system based on co-platforming

Component-based control system development for agile manufacturing machine systems

It is now a common sense that manufactures including machine suppliers and system integrators of the 21 st century will need to compete on global marketplaces, which are frequently shifting and fragmenting, with new technologies continuously emerging. Future production machines and manufacturing systems need to offer the "agility" required in providing responsiveness to product changes and the ability to reconfigure. The primary aim for this research is to advance studies in machine control system design, in the context of the European project VIR-ENG - "Integrated Design, Simulation and Distributed Control of Agile Modular Machinery"

Design and Management of Manufacturing Systems

Although the design and management of manufacturing systems have been explored in the literature for many years now, they still remain topical problems in the current scientific research. The changing market trends, globalization, the constant pressure to reduce production costs, and technical and technological progress make it necessary to search for new manufacturing methods and ways of organizing them, and to modify manufacturing system design paradigms. This book presents current research in different areas connected with the design and management of manufacturing systems and covers such subject areas as: methods supporting the design of manufacturing systems, methods of improving maintenance processes in companies, the design and improvement of manufacturing processes, the control of production processes in modern manufacturing systems production methods and techniques used in modern manufacturing systems and environmental aspects of production and their impact on the design and management of manufacturing systems. The wide range of research findings reported in this book confirms that the design of manufacturing systems is a complex problem and that the achievement of goals set for modern manufacturing systems requires interdisciplinary knowledge and the simultaneous design of the product, process and system, as well as the knowledge of modern manufacturing and organizational methods and techniques