10 research outputs found
Recommended from our members
Energy-Efficient Time-Based Encoders and Digital Signal Processors in Continuous Time
Continuous-time (CT) data conversion and continuous-time digital signal processing (DSP) are an interesting alternative to conventional methods of signal conversion and processing. This alternative proposes time-based encoding that may not suffer from aliasing; shows superior spectral properties (e.g. no quantization noise floor); and enables time-based, event-driven, flexible signal processing using digital circuits, thus scaling well with technology. Despite these interesting features, this approach has so far been limited by the CT encoder, due to both its relatively poor energy efficiency and the constraints it imposes on the subsequent CT DSP. In this thesis, we present three principles that address these limitations and help improve the CT ADC/DSP system.
First, an adaptive-resolution encoding scheme that achieves first-order reconstruction with simple circuitry is proposed. It is shown that for certain signals, the scheme can significantly reduce the number of samples generated per unit of time for a given accuracy compared to schemes based on zero-order-hold reconstruction, thus promising to lead to low dynamic power dissipation at the system level.
Presented next is a novel time-based CT ADC architecture, and associated encoding scheme, that allows a compact, energy-efficient circuit implementation, and achieves first-order quantization error spectral shaping. The design of a test chip, implemented in a 0.65-V 28-nm FDSOI process, that includes this CT ADC and a 10-tap programmable FIR CT DSP to process its output is described. The system achieves 32 dB – 42 dB SNDR over a 10 MHz – 50 MHz bandwidth, occupies 0.093 mm2, and dissipates 15 µW–163 µW as the input amplitude goes from zero to full scale.
Finally, an investigation into the possibility of CT encoding using voltage-controlled oscillators is undertaken, and it leads to a CT ADC/DSP system architecture composed primarily of asynchronous digital delays. The latter makes the system highly digital and technology-scaling-friendly and, hence, is particularly attractive from the point of view of technology migration. The design of a test chip, where this delay-based CT ADC/DSP system architecture is used to implement a 16-tap programmable FIR filter, in a 1.2-V 28-nm FDSOI process, is described. Simulations show that the system will achieve a 33 dB – 40 dB SNDR over a 600 MHz bandwidth, while dissipating 4 mW
Recommended from our members
Design Techniques for High-Performance SAR A/D Converters
The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs.
ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption.
Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s.
The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew
calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology
A high speed serializer/deserializer design
A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design.
A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption.
A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset).
With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage.
A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit.
The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications
Recommended from our members
Algorithm and Hardware Co-Design for Local/Edge Computing
Advances in VLSI manufacturing and design technology over the decades have created many computing paradigms for disparate computing needs. With concerns for transmission cost, security, latency of centralized computing, edge/local computing are increasingly prevalent in the faster growing sectors like Internet-of-Things (IoT) and other sectors that require energy/connectivity autonomous systems such as biomedical and industrial applications.
Energy and power efficient are the main design constraints in local and edge computing. While there exists a wide range of low power design techniques, they are often underutilized in custom circuit designs as the algorithms are developed independent of the hardware. Such compartmentalized design approach fails to take advantage of the many compatible algorithmic and hardware techniques that can improve the efficiency of the entire system. Algorithm hardware co-design is to explore the design space with whole stack awareness.
The main goal of the algorithm hardware co-design methodology is the enablement and improvement of small form factor edge and local VLSI systems operating under strict constraints of area and energy efficiency. This thesis presents selected works of application specific digital and mixed-signal integrated circuit designs. The application space ranges from implantable biomedical devices to edge machine learning acceleration
Digital-Based Analog Processing in Nanoscale CMOS ICs for IoT Applications
L'abstract è presente nell'allegato / the abstract is in the attachmen
Low power digital baseband core for wireless Micro-Neural-Interface using CMOS sub/near-threshold circuit
This thesis presents the work on designing and implementing a low power digital baseband core with custom-tailored protocol for wirelessly powered Micro-Neural-Interface (MNI) System-on-Chip (SoC) to be implanted within the skull to record cortical neural activities. The core, on the tag end of distributed sensors, is designed to control the operation of individual MNI and communicate and control MNI devices implanted across the brain using received downlink commands from external base station and store/dump targeted neural data uplink in an energy efficient manner. The application specific protocol defines three modes (Time Stamp Mode, Streaming Mode and Snippet Mode) to extract neural signals with on-chip signal conditioning and discrimination. In Time Stamp Mode, Streaming Mode and Snippet Mode, the core executes basic on-chip spike discrimination and compression, real-time monitoring and segment capturing of neural signals so single spike timing as well as inter-spike timing can be retrieved with high temporal and spatial resolution. To implement the core control logic using sub/near-threshold logic, a novel digital design methodology is proposed which considers INWE (Inverse-Narrow-Width-Effect), RSCE (Reverse-Short-Channel-Effect) and variation comprehensively to size the transistor width and length accordingly to achieve close-to-optimum digital circuits. Ultra-low-power cell library containing 67 cells including physical cells and decoupling capacitor cells using the optimum fingers is designed, laid-out, characterized, and abstracted. A robust on-chip sense-amp-less SRAM memory (8X32 size) for storing neural data is implemented using 8T topology and LVT fingers. The design is validated with silicon tapeout and measurement shows the digital baseband core works at 400mV and 1.28 MHz system clock with an average power consumption of 2.2 μW, resulting in highest reported communication power efficiency of 290Kbps/μW to date
Low Power Memory/Memristor Devices and Systems
This reprint focusses on achieving low-power computation using memristive devices. The topic was designed as a convenient reference point: it contains a mix of techniques starting from the fundamental manufacturing of memristive devices all the way to applications such as physically unclonable functions, and also covers perspectives on, e.g., in-memory computing, which is inextricably linked with emerging memory devices such as memristors. Finally, the reprint contains a few articles representing how other communities (from typical CMOS design to photonics) are fighting on their own fronts in the quest towards low-power computation, as a comparison with the memristor literature. We hope that readers will enjoy discovering the articles within
Intelligent Circuits and Systems
ICICS-2020 is the third conference initiated by the School of Electronics and Electrical Engineering at Lovely Professional University that explored recent innovations of researchers working for the development of smart and green technologies in the fields of Energy, Electronics, Communications, Computers, and Control. ICICS provides innovators to identify new opportunities for the social and economic benefits of society.  This conference bridges the gap between academics and R&D institutions, social visionaries, and experts from all strata of society to present their ongoing research activities and foster research relations between them. It provides opportunities for the exchange of new ideas, applications, and experiences in the field of smart technologies and finding global partners for future collaboration. The ICICS-2020 was conducted in two broad categories, Intelligent Circuits & Intelligent Systems and Emerging Technologies in Electrical Engineering