On the vehicle sideslip angle estimation: a literature review of methods, models and innovations

Typical active safety systems controlling the dynamics of passenger cars rely on real-time monitoring of the vehicle sideslip angle (VSA), together with other signals like wheel angular velocities, steering angle, lateral acceleration, and the rate of rotation about the vertical axis, known as the yaw rate. The VSA (aka attitude or “drifting” angle) is defined as the angle between the vehicle longitudinal axis and the direction of travel, taking the centre of gravity as a reference. It is basically a measure of the misalignment between vehicle orientation and trajectory therefore it is a vital piece of information enabling directional stability assessment, in transients following emergency manoeuvres for instance. As explained in the introduction the VSA is not measured directly for impracticality and it is estimated on the basis of available measurements like wheel velocities, linear and angular accelerations etc. This work is intended to provide a comprehensive literature review on the VSA estimation problem. Two main estimation methods have been categorised, i.e. Observer-based and Neural Network-based, focusing on the most effective and innovative approaches. As the first method normally relies on a vehicle model, a review of the vehicle models has been included. Advantages and limitations of each technique have been highlighted and discussed

モーションコントロールへの応用のためのカルマンフィルタに関する研究 : デュアルレート・時間遅延補償・パラメータ推定

学位の種別: 課程博士審査委員会委員 : (主査)東京大学教授 堀 洋一, 東京大学教授 大崎 博之, 東京大学教授 古関 隆章, 東京大学教授 久保田 孝, 東京大学客員准教授 坂井 真一郎, 東京大学准教授 藤本 博志University of Tokyo(東京大学

A Factor-Graph-Based Approach to Vehicle Sideslip Angle Estimation

Sideslip angle is an important variable for understanding and monitoring vehicle dynamics, but there is currently no inexpensive method for its direct measurement. Therefore, it is typically estimated from proprioceptive sensors onboard using filtering methods from the family of the Kalman filter. As a novel alternative, this work proposes modeling the problem directly as a graphical model (factor graph), which can then be optimized using a variety of methods, such as whole-dataset batch optimization for offline processing or fixed-lag smoothing for on-line operation. Experimental results on real vehicle datasets validate the proposal, demonstrating a good agreement between estimated and actual sideslip angle, showing similar performance to state-of-the-art methods but with a greater potential for future extensions due to the more flexible mathematical framework. An open-source implementation of the proposed framework has been made available online

Corner-based estimation of tire forces and vehicle velocities robust to road conditions

The final publication is available at Elsevier via https://doi.org/10.1016/j.conengprac.2017.01.009 © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/Recent developments in vehicle stability control and active safety systems have led to an interest in reliable vehicle state estimation on various road conditions. This paper presents a novel method for tire force and velocity estimation at each corner to monitor tire capacities individually. This is entailed for more demanding advanced vehicle stability systems and especially in full autonomous driving in harsh maneuvers. By integrating the lumped LuGre tire model and the vehicle kinematics, it is shown that the proposed corner-based estimator does not require knowledge of the road friction and is robust to model uncertainties. The stability of the time-varying longitudinal and lateral velocity estimators is explored. The proposed method is experimentally validated in several maneuvers on different road surface frictions. The experimental results confirm the accuracy and robustness of the state estimators.Automotive Partnership Canada, Ontario Research Fund, General Motors Co

Longitudinal vehicle state estimation using nonlinear and parameter-varying observers

The final publication is available at Elsevier via https://doi.org/10.1016/j.mechatronics.2017.02.004 © 2017. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/A corner-based velocity estimation approach is proposed which is used for vehicle’s traction and stability control systems. This approach incorporates internal tire states within the vehicle kinematics and enables the velocity estimator to work for a wide range of maneuvers without road friction information. Tire models have not been widely implemented in velocity estimators because of uncertain road friction and varying tire parameters, but the current study utilizes a simplified LuGre model with the minimum number of tire parameters and estimates velocity robust to model uncertainties. The proposed observer uses longitudinal forces, updates the states by minimizing the longitudinal force estimation error, and provides accurate outcomes at each tire. The estimator structure is shown to be robust to road conditions and rejects disturbances and model uncertainties effectively. Taking into account the vehicle dynamics is time-varying, the stability of the observer for the linear parameter varying model is proved, time-varying observer gains are designed, and the performance is studied. Road test experiments have been conducted and the results are used to validate the proposed approach.Automotive Partnership Canada [APCPJ 395996-09], Ontario Research Fund [ORF-RE-04-039], General Motors Co

Estimation of longitudinal speed robust to road conditions for ground vehicles

This is an Accepted Manuscript of an article published by Taylor & Francis in Vehicle System Dynamics on June 14 2016 available online: http://dx.doi.org/10.1080/00423114.2016.1178391This article seeks to develop a longitudinal vehicle velocity estimator robust to road conditions by employing a tyre model at each corner. Combining the lumped LuGre tyre model and the vehicle kinematics, the tyres internal deflection state is used to gain an accurate estimation. Conventional kinematic-based velocity estimators use acceleration measurements, without correction with the tyre forces. However, this results in inaccurate velocity estimation because of sensor uncertainties which should be handled with another measurement such as tyre forces that depend on unknown road friction. The new Kalman-based observer in this paper addresses this issue by considering tyre nonlinearities with a minimum number of required tyre parameters and the road condition as uncertainty. Longitudinal forces obtained by the unscented Kalman filter on the wheel dynamics is employed as an observation for the Kalman-based velocity estimator at each corner. The stability of the proposed time-varying estimator is investigated and its performance is examined experimentally in several tests and on different road surface frictions. Road experiments and simulation results show the accuracy and robustness of the proposed approach in estimating longitudinal speed for ground vehicles

Simultaneous Estimation of Vehicle Sideslip and Roll Angles Using an Integral-Based Event-Triggered Hinfinity Observer Considering Intravehicle Communications

In recent years, several technological advances have been incorporated into vehicles to ensure their safety and ride comfort. Most of these driver-assistance technologies aim to prevent skidding, whereas less attention has been paid to the avoidance of other dangerous situations such as a rollover. Since knowledge of slip and roll angles is critical to the control and safety of vehicle handling, their estimation remains of great interest when addressing emerging constraints in modern technologies involving networked communications and distributed computing. This paper presents an integral-based event-triggered H ¿ observer to simultaneously estimate the sideslip and roll angles, considering intravehicle communications with a networked-induced delay. As the longitudinal velocity and tire cornering stiffness of a vehicle can vary significantly during driving and have a strong influence on vehicle lateral stability, these time-varying parameter uncertainties are considered in the design of the observer. The simulation and experimental results demonstrate the effectiveness of the proposed observer.This work was supported by the Agencia Estatal de Investigacion (AEI) of the Ministry of Science and Innovation of the Government of Spain through the project RTI2018-095143-B-C2

Joint vehicle state and parameters estimation via Twin-in-the-Loop observers

Vehicular control systems are required to be both extremely reliable and robust to different environmental conditions, e.g. load or tire-road friction. In this paper, we extend a new paradigm for state estimation, called Twin-in-the-Loop filtering (TiL-F), to the estimation of the unknown parameters describing the vehicle operating conditions. In such an approach, a digital-twin of the vehicle (usually already available to the car manufacturer) is employed on-board as a plant replica within a closed-loop scheme, and the observer gains are tuned purely from experimental data. The proposed approach is validated against experimental data, showing to significantly outperform the state-of-the-art solutions.Comment: Preprint under review at Vehicle Systems Dynamic

Full Vehicle State Estimation Using a Holistic Corner-based Approach

Vehicles' active safety systems use different sensors, vehicle states, and actuators, along with an advanced control algorithm, to assist drivers and to maintain the dynamics of a vehicle within a desired safe range in case of instability in vehicle motion. Therefore, recent developments in such vehicle stability control and autonomous driving systems have led to substantial interest in reliable road angle and vehicle states (tire forces and vehicle velocities) estimation. Advances in applications of sensor technologies, sensor fusion, and cooperative estimation in intelligent transportation systems facilitate reliable and robust estimation of vehicle states and road angles. In this direction, developing a flexible and reliable estimation structure at a reasonable cost to operate the available sensor data for the proper functioning of active safety systems in current vehicles is a preeminent objective of the car manufacturers in dealing with the technological changes in the automotive industry. This thesis presents a novel generic integrated tire force and velocity estimation system at each corner to monitor tire capacities and slip condition individually and to address road uncertainty issues in the current model-based vehicle state estimators. Tire force estimators are developed using computationally efficient nonlinear and Kalman-based observers and common measurements in production vehicles. The stability and performance of the time-varying estimators are explored and it is shown that the developed integrated structure is robust to model uncertainties including tire properties, inflation pressure, and effective rolling radius, does not need tire parameters and road friction information, and can transfer from one car to another. The main challenges for velocity estimation are the lack of knowledge of road friction in the model-based methods and accumulated error in kinematic-based approaches. To tackle these issues, the lumped LuGre tire model is integrated with the vehicle kinematics in this research. It is shown that the proposed generic corner-based estimator reduces the number of required tire parameters significantly and does not require knowledge of the road friction. The stability and performance of the time-varying velocity estimators are studied and the sensitivity of the observers' stability to the model parameter changes is discussed. The proposed velocity estimators are validated in simulations and road experiments with two vehicles in several maneuvers with various driveline configurations on roads with different friction conditions. The simulation and experimental results substantiate the accuracy and robustness of the state estimators for even harsh maneuvers on surfaces with varying friction. A corner-based lateral state estimation is also developed for conventional cars application independent of the wheel torques. This approach utilizes variable weighted axles' estimates and high slip detection modules to deal with uncertainties associated with longitudinal forces in large steering. Therefore, the output of the lateral estimator is not altered by the longitudinal force effect and its performance is not compromised. A method for road classification is also investigated utilizing the vehicle lateral response in diverse maneuvers. Moreover, the designed estimation structure is shown to work with various driveline configurations such as front, rear, or all-wheel drive and can be easily reconfigured to operate with different vehicles and control systems' actuator configurations such as differential braking, torque vectoring, or their combinations on the front or rear axles. This research has resulted in two US pending patents on vehicle speed estimation and sensor fault diagnosis and successful transfer of these patents to industry