Low Voltage Floating Gate MOS Transistor Based Four-Quadrant Multiplier

This paper presents a four-quadrant multiplier based on square-law characteristic of floating gate MOSFET (FGMOS) in saturation region. The proposed circuit uses square-difference identity and the differential voltage squarer proposed by Gupta et al. to implement the multiplication function. The proposed multiplier employs eight FGMOS transistors and two resistors only. The FGMOS implementation of the multiplier allows low voltage operation, reduced power consumption and minimum transistor count. The second order effects caused due to mobility degradation, component mismatch and temperature variations are discussed. Performance of the proposed circuit is verified at ±0.75 V in TSMC 0.18 µm CMOS, BSIM3 and Level 49 technology by using Cadence Spectre simulator

Design of a Torque Current Generator for Strapdown Gyroscopes

The design, analysis, and experimental evaluation of an optimum performance torque current generator for use with strapdown gyroscopes, is presented. Among the criteria used to evaluate the design were the following: (1) steady-state accuracy; (2) margins of stability against self-oscillation; (3) temperature variations; (4) aging; (5) static errors drift errors, and transient errors, (6) classical frequency and time domain characteristics; and (7) the equivalent noise at the input of the comparater operational amplifier. The DC feedback loop of the torque current generator was approximated as a second-order system. Stability calculations for gain margins are discussed. Circuit diagrams are shown and block diagrams showing the implementation of the torque current generator are discussed

An Ultra-Low-Power Oscillator with Temperature and Process Compensation for UHF RFID Transponder

This paper presents a 1.28MHz ultra-low-power oscillator with temperature and process compensation. It is very suitable for clock generation circuits used in ultra-high-frequency (UHF) radio-frequency identification (RFID) transponders. Detailed analysis of the oscillator design, including process and temperature compensation techniques are discussed. The circuit is designed using TSMC 0.18μm standard CMOS process and simulated with Spectre. Simulation results show that, without post-fabrication calibration or off-chip components, less than ±3% frequency variation is obtained from –40 to 85°C in three different process corners. Monte Carlo simulations have also been performed, and demonstrate a 3σ deviation of about 6%. The power for the proposed circuitry is only 1.18µW at 27°C

A 1.8-V 4-ppm oC Reference Current with Process and Temperature

[[abstract]]A current reference generator with a proposed compensation circuit against temperature variation is presented. The current reference generator provides a reference current of 10 uA with temperature coefficient (TC) of 4 ppm/°C under temperature range from -40 to 125°C. The circuit occupies 0.008 mm2 in a 180-nm standard CMOS process.[[conferencetype]]國際[[conferencedate]]20130630~20130703[[booktype]]電子版[[iscallforpapers]]Y[[conferencelocation]]Yeosu, Kore

An accurate, trimless, high PSRR, low-voltage, CMOS bandgap reference IC

Bandgap reference circuits are used in a host of analog, digital, and mixed-signal systems to establish an accurate voltage standard for the entire IC. The accuracy of the bandgap reference voltage under steady-state (dc) and transient (ac) conditions is critical to obtain high system performance. In this work, the impact of process, power-supply, load, and temperature variations and package stresses on the dc and ac accuracy of bandgap reference circuits has been analyzed. Based on this analysis, the a bandgap reference that 1. has high dc accuracy despite process and temperature variations and package stresses, without resorting to expensive trimming or noisy switching schemes, 2. has high dc and ac accuracy despite power-supply variations, without using large off-chip capacitors that increase bill-of-material costs, 3. has high dc and ac accuracy despite load variations, without resorting to error-inducing buffers, 4. is capable of producing a sub-bandgap reference voltage with a low power-supply, to enable it to operate in modern, battery-operated portable applications, 5. utilizes a standard CMOS process, to lower manufacturing costs, and 6. is integrated, to consume less board space has been proposed. The functionality of critical components of the system has been verified through prototypes after which the performance of the complete system has been evaluated by integrating all the individual components on an IC. The proposed CMOS bandgap reference can withstand 5mA of load variations while generating a reference voltage of 890mV that is accurate with respect to temperature to the first order. It exhibits a trimless, dc 3-sigma accuracy performance of 0.84% over a temperature range of -40°C to 125°C and has a worst case ac power-supply ripple rejection (PSRR) performance of 30dB up to 50MHz using 60pF of on-chip capacitance. All the proposed techniques lead to the development of a CMOS bandgap reference that meets the low-cost, high-accuracy demands of state-of-the-art System-on-Chip environments.Ph.D.Committee Chair: Rincon-Mora, Gabriel; Committee Member: Ayazi, Farrokh; Committee Member: Bhatti, Pamela; Committee Member: Leach, W. Marshall; Committee Member: Morley, Thoma

A Sub-kT/q Voltage Reference Operating at 150 mV

We propose a subthreshold CMOS voltage reference operating with a minimum supply voltage of only 150 mV, which is three times lower than the minimum value presently reported in the literature. The generated reference voltage is only 17.69 mV. This result has been achieved by introducing a temperature compensation technique that does not require the drain-source voltage of each MOSFET to be larger than 4kT/q. The implemented solution consists in two transistors voltage reference with two MOSFETs of the same threshold-type and exploits the dependence of the threshold voltage on transistor size. Measurements performed over a large sample population of 60 chips from two separate batches show a standard deviation of only 0.29 mV. The mean variation of the reference voltage for VDD ranging from 0.15 to 1.8 V is 359.5 μV/V, whereas the mean variation of VREF in the temperature range from 0°C to 120°C is 26.74 μV/°C. The mean power consumption at 25 °C for VDD = 0.15 V is 26.1 pW. The occupied area is 1200 μm2

Design And Simulation Of Cmos-Based Bandgap Reference Voltage With Compensation Circuit Using 0.18 Μm Process Technology

Voltage reference circuit is important in electronic world nowadays. A CMOS based bandgap reference (BGR) circuit is preferred due to its size is smaller and consume less power. However, the drawback is the reference voltage variation of CMOS based BGR circuit is big in wide range of temperature, thus the temperature coefficient of it is high. Hence, an improved version of piecewise curvature-corrected Bandgap voltage reference circuit which has low voltage variation in wide range of temperature is introduced in this project to overcome the problem mentioned above. The BGR circuit is designed using CMOS compatible process in 0.18μm CMOS process technology and simulated by using Cadence tool. The proposed piecewise curvature-corrected BGR operate properly with output voltage of 558.6 mV to 558.3 mV by varying the voltage supply 1.4 V to 3.3 V at 27°C and the line regulation is 0.016% . Besides that, the best temperature coefficient obtained is 9.2 ppm/°C in the temperature range of -25°C to 150°C at 1.8 V. The PSSR of the proposed circuit is -69.91 dB at frequency less 10 kHz. The layout design of the proposed circuit is done by using Silterra 0.18 μm standard CMOS process and total die area is 0.0175 mm2 and temperature coefficient obtained in post layout simulation is 11.66ppm/°C. In short, it is found that the proposed design of BGR circuit is able to achieve high temperature range and relatively low voltage variation

Integrated Circuits for Programming Flash Memories in Portable Applications

Smart devices such as smart grids, smart home devices, etc. are infrastructure systems that connect the world around us more than before. These devices can communicate with each other and help us manage our environment. This concept is called the Internet of Things (IoT). Not many smart nodes exist that are both low-power and programmable. Floating-gate (FG) transistors could be used to create adaptive sensor nodes by providing programmable bias currents. FG transistors are mostly used in digital applications like Flash memories. However, FG transistors can be used in analog applications, too. Unfortunately, due to the expensive infrastructure required for programming these transistors, they have not been economical to be used in portable applications. In this work, we present low-power approaches to programming FG transistors which make them a good candidate to be employed in future wireless sensor nodes and portable systems. First, we focus on the design of low-power circuits which can be used in programming the FG transistors such as high-voltage charge pumps, low-drop-out regulators, and voltage reference cells. Then, to achieve the goal of reducing the power consumption in programmable sensor nodes and reducing the programming infrastructure, we present a method to program FG transistors using negative voltages. We also present charge-pump structures to generate the necessary negative voltages for programming in this new configuration