Constraint-driven RF test stimulus generation and built-in test

With the explosive growth in wireless applications, the last decade witnessed an ever-increasing test challenge for radio frequency (RF) circuits. While the design community has pushed the envelope far into the future, by expanding CMOS process to be used with high-frequency wireless devices, test methodology has not advanced at the same pace. Consequently, testing such devices has become a major bottleneck in high-volume production, further driven by the growing need for tighter quality control. RF devices undergo testing during the prototype phase and during high-volume manufacturing (HVM). The benchtop test equipment used throughout prototyping is very precise yet specialized for a subset of functionalities. HVM calls for a different kind of test paradigm that emphasizes throughput and sufficiency, during which the projected performance parameters are measured one by one for each device by automated test equipment (ATE) and compared against defined limits called specifications. The set of tests required for each product differs greatly in terms of the equipment required and the time taken to test individual devices. Together with signal integrity, precision, and repeatability concerns, the initial cost of RF ATE is prohibitively high. As more functionality and protocols are integrated into a single RF device, the required number of specifications to be tested also increases, adding to the overall cost of testing, both in terms of the initial and recurring operating costs. In addition to the cost problem, RF testing proposes another challenge when these components are integrated into package-level system solutions. In systems-on-packages (SOP), the test problems resulting from signal integrity, input/output bandwidth (IO), and limited controllability and observability have initiated a paradigm shift in high-speed analog testing, favoring alternative approaches such as built-in tests (BIT) where the test functionality is brought into the package. This scheme can make use of a low-cost external tester connected through a low-bandwidth link in order to perform demanding response evaluations, as well as make use of the analog-to-digital converters and the digital signal processors available in the package to facilitate testing. Although research on analog built-in test has demonstrated hardware solutions for single specifications, the paradigm shift calls for a rather general approach in which a single methodology can be applied across different devices, and multiple specifications can be verified through a single test hardware unit, minimizing the area overhead. Specification-based alternate test methodology provides a suitable and flexible platform for handling the challenges addressed above. In this thesis, a framework that integrates ATE and system constraints into test stimulus generation and test response extraction is presented for the efficient production testing of high-performance RF devices using specification-based alternate tests. The main components of the presented framework are as follows: Constraint-driven RF alternate test stimulus generation: An automated test stimulus generation algorithm for RF devices that are evaluated by a specification-based alternate test solution is developed. The high-level models of the test signal path define constraints in the search space of the optimized test stimulus. These models are generated in enough detail such that they inherently define limitations of the low-cost ATE and the I/O restrictions of the device under test (DUT), yet they are simple enough that the non-linear optimization problem can be solved empirically in a reasonable amount of time. Feature extractors for BIT: A methodology for the built-in testing of RF devices integrated into SOPs is developed using additional hardware components. These hardware components correlate the high-bandwidth test response to low bandwidth signatures while extracting the test-critical features of the DUT. Supervised learning is used to map these extracted features, which otherwise are too complicated to decipher by plain mathematical analysis, into the specifications under test. Defect-based alternate testing of RF circuits: A methodology for the efficient testing of RF devices with low-cost defect-based alternate tests is developed. The signature of the DUT is probabilistically compared with a class of defect-free device signatures to explore possible corners under acceptable levels of process parameter variations. Such a defect filter applies discrimination rules generated by a supervised classifier and eliminates the need for a library of possible catastrophic defects.Ph.D.Committee Chair: Chatterjee, Abhijit; Committee Member: Durgin, Greg; Committee Member: Keezer, David; Committee Member: Milor, Linda; Committee Member: Sitaraman, Sures

A built-in self-test technique for high speed analog-to-digital converters

Fundação para a Ciência e a Tecnologia (FCT) - PhD grant (SFRH/BD/62568/2009

An Analysis of the Conventional Wire Maintenance Methods and Transition Wire Integrity Programs Utilized in the Aviation Industry.

Aging aircraft wiring poses a significant threat to both commercial and military aircraft. Recent air disasters involving aging aircraft wiring have made it clear that aging wiring can be catastrophic. Aging of an electrical wiring system can result in loss of critical functions of equipment or loss of information regarding equipment operation. Either result can lead to an electrical failure causing smoke and fire, consequently being a danger to public health and aircraft safety. Conventional maintenance practices do not effectively manage aging wiring problems. More proactive methods are needed so that aircraft wiring failures can be anticipated and wiring systems can be repaired or replaced before failures occur. This thesis will identify the effects of aging wiring systems, the potential degradation to aircraft safety and regulations regarding aircraft wire safety. This thesis will evaluate the conventional wire maintenance practices and transition wire integrity programs in the aviation industry

A wireless system for crack monitoring in concrete structures

The formation of cracks in concrete is a normal phenomenon. However, effective control and prevention of the formation of cracks is the key for successful life of concrete structures. Specifically, cracks represent a path of least resistance for moisture and corrosive ionic agents from de-icing salts to reach embedded steel in concrete. Commercial wireless sensor networks utilizing crack gauge sensors can be applied for crack monitoring in the common concrete structure. The crack sensors circuits\u27 boards, which are used to stimulate the cracks, are currently unavailable for the SG-Link module platform. The SG-Link module is an ultra-low-power module for use in sensor networks, monitoring applications and rapid application prototyping. Therefore, a crack sensor circuit board for the SG-Link module platform has been developed. The development of a smart wireless sensor network for the crack monitoring system is divided into four parts: a crack gauge sensor, signal conditioning, the SG-Link module, and a base station unit. The signal conditioning module consists of a crack gauge sensor, a wheatstone bridge, an amplifier, and a filter. The SG-Link module consists of an analog to digital converter (ADC), a microcontroller unit (MCC), and a transmitter with an antenna. The base station unit includes an antenna and a receiver module connected to the base station or computer. In this study, cracks are monitored based on the change of the electrical resistance between the sensor\u27s two terminals that are taken from the simulation model of the crack sensor board consisting of a crack gauge sensor and signal conditioning. This thesis looked at the effectiveness of a wireless system for crack monitoring in concrete structures. Tests were conducted in a laboratory to monitor the cracks in the structures and explore the validity and reliability of the monitoring mechanism and data transmission

Index to NASA Tech Briefs, 1975

This index contains abstracts and four indexes--subject, personal author, originating Center, and Tech Brief number--for 1975 Tech Briefs

Approach to In Situ Component Level Electronics Assembly Repair (CLEAR) for Constellation

Maintenance resupply is a significant issue for long duration space missions. Currently, the International Space Station (ISS) approaches maintenance primarily around replaceable modules called Orbital Replacement Units (ORU). While swapping out ORUs has served the ISS well keeping crew time for maintenance to a minimum, this approach assumes a substantial logistics capacity to provide replacement ORUs and return ORUs to Earth for repair. The ORUs used for ISS require relatively large blocks of replacement hardware even though the actual failed component may be several orders of magnitude smaller. The Component Level Electronics Assembly Repair (CLEAR) task was created to explore electronics repair down to the component level for future space missions. From 2006 to 2009, CLEAR was an activity under the Supportability project of the Exploration Technology Development Program. This paper describes the activities of CLEAR including making a case for component-level electronics repair, examination of current terrestrial repair hardware, and potential repair needs. Based on those needs, the CLEAR team proposes an architecture for an in-situ repair capability aboard a spacecraft or habitat. Additionally, this paper discusses recent progress toward developing in-space repair capabilities--including two spaceflight experiments-- and presents technology concepts which could help enable or benefit the same

Efficient verification/testing of system-on-chip through fault grading and analog behavioral modeling

textThis dissertation presents several cost-effective production test solutions using fault grading and mixed-signal design verification cases enabled by analog behavioral modeling. Although the latest System-on-Chip (SOC) is getting denser, faster, and more complex, the manufacturing technology is dominated by subtle defects that are introduced by small-scale technology. Thus, SOC requires more mature testing strategies. By performing various types of testing, better quality SoC can be manufactured, but test resources are too limited to accommodate all those tests. To create the most efficient production test flow, any redundant or ineffective tests need to be removed or minimized. Chapter 3 proposes new method of test data volume reduction by combining the nonlinear property of feedback shift register (FSR) and dictionary coding. Instead of using the nonlinear FSR for actual hardware implementation, the expanded test set by nonlinear expansion is used as the one-column test sets and provides big reduction ratio for the test data volume. The experimental results show the combined method reduced the total test data volume and increased the fault coverage. Due to the increased number of test patterns, total test time is increased. Chapter 4 addresses a whole process of functional fault grading. Fault grading has always been a ”desire-to-have” flow because it can bring up significant value for cost saving and yield analysis. However, it is very hard to perform the fault grading on the complex large scale SOC. A commercial tool called Z01X is used as a fault grading platform, and whole fault grading process is coordinated and each detailed execution is performed. Simulation- based functional fault grading identifies the quality of the given functional tests against the static faults and transition delay faults. With the structural tests and functional tests, functional fault grading can indicate the way to achieve the same test coverage by spending minimal test time. Compared to the consumed time and resource for fault grading, the contribution to the test time saving might not be acceptable as very promising, but the fault grading data can be reused for yield analysis and test flow optimization. For the final production testing, confident decisions on the functional test selection can be made based on the fault grading results. Chapter 5 addresses the challenges of Package-on-Package (POP) testing. Because POP devices have pins on both the top and the bottom of the package, the increased test pins require more test channels to detect packaging defects. Boundary scan chain testing is used to detect those continuity defects by relying on leakage current from the power supply. This proposed test scheme does not require direct test channels on the top pins. Based on the counting algorithm, minimal numbers of test cycles are generated, and the test achieved full test coverage for any combinations of pin-to-pin shortage defects on the top pins of the POP package. The experimental results show about 10 times increased leakage current from the shorted defect. Also, it can be expanded to multi-site testing with less test channels for high-volume production. Fault grading is applied within different structural test categories in Chapter 6. Stuck-at faults can be considered as TDFs having infinite delay. Hence, the TDF Automatic Test Pattern Generation (ATPG) tests can detect both TDFs and stuck-at faults. By removing the stuck-at faults being detected by the given TDF ATPG tests, the tests that target stuck-at faults can be reduced, and the reduced stuck-at fault set results in fewer stuck-at ATPG patterns. The structural test time is reduced while keeping the same test coverage. This TDF grading is performed with the same ATPG tool used to generate the stuck-at and TDF ATPG tests. To expedite the mixed-signal design verification of complex SoC, analog behavioral modeling methods and strategies are addressed in Chapter 7 and case studies for detailed verification with actual mixed-signal design are ad- dressed in Chapter 8. Analog modeling effort can enhance verification quality for a mixed-signal design with less turnaround time, and it enables compatible integration of the mixed-signal design cores into the SoC. The modeling process may reveal any potential design errors or incorrect testbench setup, and it results in minimizing unnecessary debugging time for quality devices. Two mixed-signal design cases were verified by me using the analog models. A fully hierarchical digital-to-analog converter (DAC) model is implemented and silicon mismatches caused by process variation are modeled and inserted into the DAC model, and the calibration algorithm for the DAC is successfully verified by model-based simulation at the full DAC-level. When the mismatch amount is increased and exceeded the calibration capability of the DAC, the simulation results show the increased calibration error with some outliers. This verification method can identify the saturation range of the DAC and predict the yield of the devices from process variation. A phase-locked loop (PLL) design cases were also verified by me using the analog model. Both open-loop PLL model and closed-loop PLL model cases are presented. Quick bring-up of open-loop PLL model provides low simulation overhead for widely-used PLLs in the SOC and enables early starting of design verification for the upper-level design using the PLL generated clocks. Accurate closed-loop PLL model is implemented for DCO-based PLL design, and the mixed-simulation with analog models and schematic designs enables flexible analog verification. Only focused analog design block is set to the schematic design and the rest of the analog design is replaced by the analog model. Then, this scaled-down SPICE simulation is performed about 10 times to 100 times faster than full-scale SPICE simulation. The analog model of the focused block is compared with the scaled-down SPICE simulation result and the quality of the model is iteratively enhanced. Hence, the analog model enables both compatible integration and flexible analog design verification. This dissertation contributes to reduce test time and to enhance test quality, and helps to set up efficient production testing flows. Depending on the size and performance of CUT, proper testing schemes can maximize the efficiency of production testing. The topics covered in this dissertation can be used in optimizing the test flow and selecting the final production tests to achieve maximum test capability. In addition, the strategies and benefits of analog behavioral modeling techniques that I implemented are presented, and actual verification cases shows the effectiveness of analog modeling for better quality SoC products.Electrical and Computer Engineerin

Design and debugging of multi-step analog to digital converters

With the fast advancement of CMOS fabrication technology, more and more signal-processing functions are implemented in the digital domain for a lower cost, lower power consumption, higher yield, and higher re-configurability. The trend of increasing integration level for integrated circuits has forced the A/D converter interface to reside on the same silicon in complex mixed-signal ICs containing mostly digital blocks for DSP and control. However, specifications of the converters in various applications emphasize high dynamic range and low spurious spectral performance. It is nontrivial to achieve this level of linearity in a monolithic environment where post-fabrication component trimming or calibration is cumbersome to implement for certain applications or/and for cost and manufacturability reasons. Additionally, as CMOS integrated circuits are accomplishing unprecedented integration levels, potential problems associated with device scaling – the short-channel effects – are also looming large as technology strides into the deep-submicron regime. The A/D conversion process involves sampling the applied analog input signal and quantizing it to its digital representation by comparing it to reference voltages before further signal processing in subsequent digital systems. Depending on how these functions are combined, different A/D converter architectures can be implemented with different requirements on each function. Practical realizations show the trend that to a first order, converter power is directly proportional to sampling rate. However, power dissipation required becomes nonlinear as the speed capabilities of a process technology are pushed to the limit. Pipeline and two-step/multi-step converters tend to be the most efficient at achieving a given resolution and sampling rate specification. This thesis is in a sense unique work as it covers the whole spectrum of design, test, debugging and calibration of multi-step A/D converters; it incorporates development of circuit techniques and algorithms to enhance the resolution and attainable sample rate of an A/D converter and to enhance testing and debugging potential to detect errors dynamically, to isolate and confine faults, and to recover and compensate for the errors continuously. The power proficiency for high resolution of multi-step converter by combining parallelism and calibration and exploiting low-voltage circuit techniques is demonstrated with a 1.8 V, 12-bit, 80 MS/s, 100 mW analog to-digital converter fabricated in five-metal layers 0.18-µm CMOS process. Lower power supply voltages significantly reduce noise margins and increase variations in process, device and design parameters. Consequently, it is steadily more difficult to control the fabrication process precisely enough to maintain uniformity. Microscopic particles present in the manufacturing environment and slight variations in the parameters of manufacturing steps can all lead to the geometrical and electrical properties of an IC to deviate from those generated at the end of the design process. Those defects can cause various types of malfunctioning, depending on the IC topology and the nature of the defect. To relive the burden placed on IC design and manufacturing originated with ever-increasing costs associated with testing and debugging of complex mixed-signal electronic systems, several circuit techniques and algorithms are developed and incorporated in proposed ATPG, DfT and BIST methodologies. Process variation cannot be solved by improving manufacturing tolerances; variability must be reduced by new device technology or managed by design in order for scaling to continue. Similarly, within-die performance variation also imposes new challenges for test methods. With the use of dedicated sensors, which exploit knowledge of the circuit structure and the specific defect mechanisms, the method described in this thesis facilitates early and fast identification of excessive process parameter variation effects. The expectation-maximization algorithm makes the estimation problem more tractable and also yields good estimates of the parameters for small sample sizes. To allow the test guidance with the information obtained through monitoring process variations implemented adjusted support vector machine classifier simultaneously minimize the empirical classification error and maximize the geometric margin. On a positive note, the use of digital enhancing calibration techniques reduces the need for expensive technologies with special fabrication steps. Indeed, the extra cost of digital processing is normally affordable as the use of submicron mixed signal technologies allows for efficient usage of silicon area even for relatively complex algorithms. Employed adaptive filtering algorithm for error estimation offers the small number of operations per iteration and does not require correlation function calculation nor matrix inversions. The presented foreground calibration algorithm does not need any dedicated test signal and does not require a part of the conversion time. It works continuously and with every signal applied to the A/D converter. The feasibility of the method for on-line and off-line debugging and calibration has been verified by experimental measurements from the silicon prototype fabricated in standard single poly, six metal 0.09-µm CMOS process