Pre-validation of SoC via hardware and software co-simulation

Abstract. System-on-chips (SoCs) are complex entities consisting of multiple hardware and software components. This complexity presents challenges in their design, verification, and validation. Traditional verification processes often test hardware models in isolation until late in the development cycle. As a result, cooperation between hardware and software development is also limited, slowing down bug detection and fixing. This thesis aims to develop, implement, and evaluate a co-simulation-based pre-validation methodology to address these challenges. The approach allows for the early integration of hardware and software, serving as a natural intermediate step between traditional hardware model verification and full system validation. The co-simulation employs a QEMU CPU emulator linked to a register-transfer level (RTL) hardware model. This setup enables the execution of software components, such as device drivers, on the target instruction set architecture (ISA) alongside cycle-accurate RTL hardware models. The thesis focuses on two primary applications of co-simulation. Firstly, it allows software unit tests to be run in conjunction with hardware models, facilitating early communication between device drivers, low-level software, and hardware components. Secondly, it offers an environment for using software in functional hardware verification. A significant advantage of this approach is the early detection of integration errors. Software unit tests can be executed at the IP block level with actual hardware models, a task previously only possible with costly system-level prototypes. This enables earlier collaboration between software and hardware development teams and smoothens the transition to traditional system-level validation techniques.Järjestelmäpiirin esivalidointi laitteiston ja ohjelmiston yhteissimulaatiolla. Tiivistelmä. Järjestelmäpiirit (SoC) ovat monimutkaisia kokonaisuuksia, jotka koostuvat useista laitteisto- ja ohjelmistokomponenteista. Tämä monimutkaisuus asettaa haasteita niiden suunnittelulle, varmennukselle ja validoinnille. Perinteiset varmennusprosessit testaavat usein laitteistomalleja eristyksissä kehityssyklin loppuvaiheeseen saakka. Tämän myötä myös yhteistyö laitteisto- ja ohjelmistokehityksen välillä on vähäistä, mikä hidastaa virheiden tunnistamista ja korjausta. Tämän diplomityön tavoitteena on kehittää, toteuttaa ja arvioida laitteisto-ohjelmisto-yhteissimulointiin perustuva esivalidointimenetelmä näiden haasteiden ratkaisemiseksi. Menetelmä mahdollistaa laitteiston ja ohjelmiston varhaisen integroinnin, toimien luonnollisena välietappina perinteisen laitteistomallin varmennuksen ja koko järjestelmän validoinnin välillä. Yhteissimulointi käyttää QEMU suoritinemulaattoria, joka on yhdistetty rekisterinsiirtotason (RTL) laitteistomalliin. Tämä mahdollistaa ohjelmistokomponenttien, kuten laiteajureiden, suorittamisen kohdejärjestelmän käskysarja-arkkitehtuurilla (ISA) yhdessä kellosyklitarkkojen RTL laitteistomallien kanssa. Työ keskittyy kahteen yhteissimulaation pääsovellukseen. Ensinnäkin se mahdollistaa ohjelmiston yksikkötestien suorittamisen laitteistomallien kanssa, varmistaen kommunikaation laiteajurien, matalan tason ohjelmiston ja laitteistokomponenttien välillä. Toiseksi se tarjoaa ympäristön ohjelmiston käyttämiseen toiminnallisessa laitteiston varmennuksessa. Merkittävä etu tästä lähestymistavasta on integraatiovirheiden varhainen havaitseminen. Ohjelmiston yksikkötestejä voidaan suorittaa jo IP-lohkon tasolla oikeilla laitteistomalleilla, mikä on aiemmin ollut mahdollista vain kalliilla järjestelmätason prototyypeillä. Tämä mahdollistaa aikaisemman ohjelmisto- ja laitteistokehitystiimien välisen yhteistyön ja helpottaa siirtymistä perinteisiin järjestelmätason validointimenetelmiin

Automated Hardware Prototyping for 3D Network on Chips

Vor mehr als 50 Jahren stellte Intel® Mitbegründer Gordon Moore eine Prognose zum Entwicklungsprozess der Transistortechnologie auf. Er prognostizierte, dass sich die Zahl der Transistoren in integrierten Schaltungen alle zwei Jahre verdoppeln wird. Seine Aussage ist immer noch gültig, aber ein Ende von Moores Gesetz ist in Sicht. Mit dem Ende von Moore’s Gesetz müssen neue Aspekte untersucht werden, um weiterhin die Leistung von integrierten Schaltungen zu steigern. Zwei mögliche Ansätze für "More than Moore” sind 3D-Integrationsverfahren und heterogene Systeme. Gleichzeitig entwickelt sich ein Trend hin zu Multi-Core Prozessoren, basierend auf Networks on chips (NoCs). Neben dem Ende des Mooreschen Gesetzes ergeben sich bei immer kleiner werdenden Technologiegrößen, vor allem jenseits der 60 nm, neue Herausforderungen. Eine Schwierigkeit ist die Wärmeableitung in großskalierten integrierten Schaltkreisen und die daraus resultierende Überhitzung des Chips. Um diesem Problem in modernen Multi-Core Architekturen zu begegnen, muss auch die Verlustleistung der Netzwerkressourcen stark reduziert werden. Diese Arbeit umfasst eine durch Hardware gesteuerte Kombination aus Frequenzskalierung und Power Gating für 3D On-Chip Netzwerke, einschließlich eines FPGA Prototypen. Dafür wurde ein Takt-synchrones 2D Netzwerk auf ein dreidimensionales asynchrones Netzwerk mit mehreren Frequenzbereichen erweitert. Zusätzlich wurde ein skalierbares Online-Power-Management System mit geringem Ressourcenaufwand entwickelt. Die Verifikation neuer Hardwarekomponenten ist einer der zeitaufwendigsten Schritte im Entwicklungsprozess hochintegrierter digitaler Schaltkreise. Um diese Aufgabe zu beschleunigen und um eine parallele Softwareentwicklung zu ermöglichen, wurde im Rahmen dieser Arbeit ein automatisiertes und benutzerfreundliches Tool für den Entwurf neuer Hardware Projekte entwickelt. Eine grafische Benutzeroberfläche zum Erstellen des gesamten Designablaufs, vom Erstellen der Architektur, Parameter Deklaration, Simulation, Synthese und Test ist Teil dieses Werkzeugs. Zudem stellt die Größe der Architektur für die Erstellung eines Prototypen eine besondere Herausforderung dar. Frühere Arbeiten haben es versäumt, eine schnelles und unkompliziertes Prototyping, insbesondere von Architekturen mit mehr als 50 Prozessorkernen, zu realisieren. Diese Arbeit umfasst eine Design Space Exploration und FPGA-basierte Prototypen von verschiedenen 3D-NoC Implementierungen mit mehr als 80 Prozessoren

Virtual Cycle-accurate Hardware and Software Co-simulation Platform for Cellular IoT

Modern embedded development flows often depend on FPGA board usage for pre-ASIC system verification. The purpose of this project is to instead explore the usage of Electronic System Level (ESL) hardware-software co-simulation through the usage of ARM SoC Designer tool to create a virtual prototype of a cellular IoT modem and thereafter compare the benefits of including such a methodology into the early development cycle. The virtual system is completely developed and executed on a host computer, without the requirement of additional hardware. The virtual prototype hardware is based on C++ ARM verified cycle-accurate models generated from RTL hardware descriptions, High-level synthesis (HLS) pre-synthesis SystemC HW accelerator models and behavioural models which implement the ARM Cycle-accurate Simulation Interface (CASI). The micro-controller of the virtual system which is based on an ARM Cortex-M processor, is capable of executing instructions from a memory module. This report documents the virtual prototype implementation and compares both the software performance and cycle-accuracy of various virtual micro-controller configurations to a commercial reference development board. By altering factors such as memory latencies and bus interconnect subsystem arbitration in co-simulations, the software cycle-count performance of the development board was shown possible to reproduce within a 5% error margin, at the cost of approximately 266 times slower execution speed. Furthermore, the validity of two HLS pre-synthesis hardware models is investigated and proven to be functionally accurate within three clock cycles of individual block latency compared to post-synthesis FPGA synthesized implementations. The final virtual prototype system consisted of the micro-controller and two cellular IoT hardware accelerators. The system runs a FreeRTOS 9.0.0 port, executing a multi-threaded program at an average clock cycle simulation frequency of 10.6 kHz.-Designing and simulating embedded computer systems virtually. Cellular internet of things (IoT) is a new technology that will enable the interconnection of everything: from street lights and parking meters to your gas or water meter at home, wireless cellular networks will allow information to be shared between devices. However, in order for these systems to provide any useful data, they need to include a computer chip with a system to manage the communication itself, enabling the connection to a cellular network and the actual transmission and reception of data. Such a chip is called an embedded chip or system. Traditionally, the design and verification of digital embedded systems, that is to say a system which has both hardware and software components, had to be done in two steps. The first step consists of designing all the hardware, testing it, integrating it and producing it physically on silicon in order to verify the intended functionality of all the components. The second step thus consists of taking the hardware that has been developed and designing the software: a program which will have to execute in complete compliance to the hardware that has been previously developed. This poses two main issues: the software engineers cannot begin their work properly until the hardware is finished, which makes the process very long, and the fact that the hardware has been printed on silicon greatly restricts the possibility of doing changes to accommodate late system requirement alterations; which is quite likely for a tailor-made application specific system such as a cellular IoT chip. A currently widespread technology used to mitigate the previously mentioned negative aspects of embedded design, is the employment of field-programmable gate array (FPGA) development boards which often contain a micro-controller (with a processor and some memories), and a gate array connected to it. The FPGA part consists of a lattice of digital logic gates which can be programmed to interconnect and represent the functionality of the hardware being designed. The processor can thus execute software instructions placed on the memories and the hardware being developed can be programmed into the gate array in order to integrate and verify a full hardware and software system. Nevertheless, this boards are expensive and limit the design to the hardware components available commercially in the different off-the-shelf models, e.g. a specific processor which might not be the desired one. Now imagine there is a way to design hardware components such as processors in the traditional way, however once the hardware has been implemented it can be integrated together with software without the need of printing a physical silicon chip specifically for this purpose. That would be extremely convenient and would save lots of time, would it not? Fortunately, this is already possible due to Electronic System Level (ESL) design, which is compilation of techniques that allow to design, simulate and partially verify a digital chip, all within any normal laptop or desktop computer. Moreover, some ESL tools such as the one investigated in this project, allow you to even simulate a program code written specifically for this hardware; this is known as virtual hardware software co-simulation. The reliability of simulation must however be considered when compared to a traditional two-step methodology or FPGA board usage to verify a full system. This is because a virtual hardware simulation can have several degrees of accuracy, depending on the specificity of component models that make up the virtual prototype of the digital system. Therefore, in order to use co-simulation techniques with a high degree of confidence for verification, the highest accuracy degree should be employed if possible to guarantee that what is being simulated will match the reality of a silicon implementation. The clock cycle-accurate level is one of the highest accuracy system simulation methods available, and it consists of representing the digital states of all hardware components such as signals and registers, in a cycle-by-cycle manner. By using the ARM SoC Designer ESL tool, we have co-designed and co-simulated several microcontrollers on a detailed, cycle-accurate level and confirmed its behaviour by comparing it to a physical reference target development board. Finally, a more complex virtual prototype of a cellular IoT system was also simulated, including a micro-controller running a a real-time operating system (RTOS), hardware accelerators and serial data interfacing. Parts of this virtual prototype where compared to an FPGA board to evaluate the pros and cons of incorporating virtual system simulation into the development cycle and to what extent can ESL methods substitute traditional verification techniques. The ease of interchanging hardware, simplicity of development, simulation speed and the level of debug capabilities available when developing in a virtual environment are some of the aspects of ARM SoC Designer discussed in this thesis. A more in depth description of the methodology and results can be found in the report titled "Virtual Cycle-accurate Hardware and Software Co-simulation Platform for Cellular IoT"

Development of a DPI-C Test Environment

Fruto da evolução tecnológica, a integração de sistemas com milhares de milhões de transístores num único circuito integrado conduziu a um aumento da complexidade dos projetos digitais. Consequentemente, o esforço/tempo necessário para o desenvolvimento destes ´e maior, tal como a probabilidade da existência de erros de hardware. De forma a evitar passar esses erros para o silício, a Synopsys, uma empresa líder em Automação de Projetos Eletrónicos (Eletronic Design Automation - EDA), e em IP (Intellectual Property), e uma das empresas responsáveis por esta evolução tecnológica, tem uma equipa de IP Prototyping Kit (IPK), que cria protótipos rápidos dos circuitos IP em sistemas baseados em Field Programmable Gate Arrays (FPGA) e outras plataformas. Durante a integração do sistema em FPGA são usadas simulações/ testbenchs em SystemVerilog (SV) e testadas as plataformas de hardware de forma a ajudar no desenvolvimento do projeto e sua depuração. O IPK permite a integração do software e do hardware numa etapa inicial do projeto. Contudo, a prototipagem pode ser um processo complicado e demorado. Para auxiliar os engenheiros a acelerar o desenvolvimento, foi proposta a criação de um ambiente de teste baseado em C, batizado de DPIC (Direct Programming Interface em C), compatível com SystemVerilog e com as plataformas de hardware para testes. Este ambiente, também chamado de C-Tests, usa o mesmo caso de estudo como parâmetro de entrada para as duas plataformas. O objetivo ´e obter o mesmo resultado em ambas, facilitando a sua comparação e o diagnóstico e resolução de qualquer problema existente.Due to the technological evolution, chip integration increased, with billions of transistors available in a single chip, and thus the complexity of the digital design. As a consequence, the development effort/time increased and accordingly the possibility of the existence of hardware bugs. In order to avoid passing these bugs to real silicon hardware, Synopsys, a leading company in Electronic Design Automation (EDA) and Semiconductor IP (Intellectual Property) and one of the responsible companies for this technological evolution, has a IP Prototyping Kit (IPK) team. The IPK team creates rapid prototypes of these circuits in Field Programmable Gate Arrays (FPGA) systems and other platforms. During system integration in FPGA, it is used simulation/testbenches in SystemVerilog (SV), and tests on real hardware to aid design and debugging. The IPK allows a software and hardware integration in an early stage of the project. However, the prototyping can be a complicated and slow process. To help engineers to accelerate this development, it was proposed the creation of a C based test environment, named DPI-C (Direct Programming Interface in C), compatible with SystemVerilog and hardware platform tests. This environment, also known as C-Tests, uses the same test case on both platforms as an input parameter. The aim is to obtain the same results, easing the comparison between them and helping to understand and solving the existing problems

Development of electronics for the VELO upgrade detector

Esta tesis cubre el diseño electrónico del detector de vértices (VELO) del experimento LHCb del CERN. El VELO está situado rodeando el punto de colisión de los dos haces de protones del LHC del CERN. Su diseño está lleno de restricciones que requieren diseños novedosos: minimizar la materia cerca del punto de colisión, diseño de componentes que soporten radiación, transmisión de datos a alta tasa y el procesado de los mismos, sincronización del sistema, etc. El trabajo presentado en esta tesis se centra en: por un lado, la validación del hardware y sus diferentes prototipos, por otro lado, el diseño del firmware de las FPGAs encargadas del control, sincronización y adquisición de datos del VELO

Low-power digital processor for wireless sensor networks

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2005.Includes bibliographical references (p. 69-72).In order to make sensor networks cost-effective and practical, the electronic components of a wireless sensor node need to run for months to years on the same battery. This thesis explores the design of a low-power digital processor for these sensor nodes, employing techniques such as hardwired algorithms, lowered supply voltages, clock gating and subsystem shutdown. Prototypes were built on both a FPGA and ASIC platform, in order to verify functionality and characterize power consumption. The resulting 0.18[micro]m silicon fabricated in National Semiconductor Corporation's process was operational for supply voltages ranging from 0.5V to 1.8V. At the lowest operating voltage of 0.5V and a frequency of 100KHz, the chip performs 8 full-accuracy FFT computations per second and draws 1.2nJ of total energy per cycle. Although this energy/cycle metric does not surpass existing low-energy processors demonstrated in literature or commercial products, several low-power techniques are suggested that could drastically improve the energy metrics of a future implementation.by Daniel Frederic Finchelstein.S.M