Design of sigma-delta modulators for analog-to-digital conversion intensively using passive circuits

This thesis presents the analysis, design implementation and experimental evaluation of passiveactive discrete-time and continuous-time Sigma-Delta (ΣΔ) modulators (ΣΔMs) analog-todigital converters (ADCs). Two prototype circuits were manufactured. The first one, a discrete-time 2nd-order ΣΔM, was designed in a 130 nm CMOS technology. This prototype confirmed the validity of the ultra incomplete settling (UIS) concept used for implementing the passive integrators. This circuit, clocked at 100 MHz and consuming 298 μW, achieves DR/SNR/SNDR of 78.2/73.9/72.8 dB, respectively, for a signal bandwidth of 300 kHz. This results in a Walden FoMW of 139.3 fJ/conv.-step and Schreier FoMS of 168 dB. The final prototype circuit is a highly area and power efficient ΣΔM using a combination of a cascaded topology, a continuous-time RC loop filter and switched-capacitor feedback paths. The modulator requires only two low gain stages that are based on differential pairs. A systematic design methodology based on genetic algorithm, was used, which allowed decreasing the circuit’s sensitivity to the circuit components’ variations. This continuous-time, 2-1 MASH ΣΔM has been designed in a 65 nm CMOS technology and it occupies an area of just 0.027 mm2. Measurement results show that this modulator achieves a peak SNR/SNDR of 76/72.2 dB and DR of 77dB for an input signal bandwidth of 10 MHz, while dissipating 1.57 mW from a 1 V power supply voltage. The ΣΔM achieves a Walden FoMW of 23.6 fJ/level and a Schreier FoMS of 175 dB. The innovations proposed in this circuit result, both, in the reduction of the power consumption and of the chip size. To the best of the author’s knowledge the circuit achieves the lowest Walden FOMW for ΣΔMs operating at signal bandwidth from 5 MHz to 50 MHz reported to date

Calibrated Continuous-Time Sigma-Delta Modulators

To provide more information mobility, many wireless communication systems such as WCDMA and EDGE in phone systems, bluetooth and WIMAX in communication networks have been recently developed. Recent efforts have been made to build the allin- one next generation device which integrates a large number of wireless services into a single receiving path in order to raise the competitiveness of the device. Among all the receiver architectures, the high-IF receiver presents several unique properties for the next generation receiver by digitalizing the signal at the intermediate frequency around a few hundred MHz. In this architecture, the modulation/demodulation schemes, protocols, equalization, etc., are all determined in a software platform that runs in the digital signal processor (DSP) or FPGA. The specifications for most of front-end building blocks are relaxed, except the analog-to-digital converter (ADC). The requirements of large bandwidth, high operational frequency and high resolution make the design of the ADC very challenging. Solving the bottleneck associated with the high-IF receiver architecture is a major focus of many ongoing research efforts. In this work, a 6th-order bandpass continuous time sigma-delta ADC with measured 68.4dB SNDR at 10MHz bandwidth to accommodate video applications is proposed. Tuned at 200 MHz, the fs/4 architecture employs an 800 MHz clock frequency. By making use of a unique software-based calibration scheme together with the tuning properties of the bandpass filters developed under the umbrella of this project, the ADC performance is optimized automatically to fulfill all requirements for the high-IF architecture. In a separate project, other critical design issues for continuous-time sigma-delta ADCs are addressed, especially the issues related to unit current source mismatches in multi-level DACs as well as excess loop delays that may cause loop instability. The reported solutions are revisited to find more efficient architectures. The aforementioned techniques are used for the design of a 25MHz bandwidth lowpass continuous-time sigma-delta modulator with time-domain two-step 3-bit quantizer and DAC for WiMAX applications. The prototype is designed by employing a level-to-pulse-width modulation (PWM) converter followed by a single-level DAC in the feedback path to translate the typical digital codes into PWM signals with the proposed pulse arrangement. Therefore, the non-linearity issue from current source mismatch in multi-level DACs is prevented. The jitter behavior and timing mismatch issue of the proposed time-based methods are fully analyzed. The measurement results of a chip prototype achieving 67.7dB peak SNDR and 78dB SFDR in 25MHz bandwidth properly demonstrate the design concepts and effectiveness of time-based quantization and feedback. Both continuous-time sigma-delta ADCs were fabricated in mainstream CMOS 0.18um technologies, which are the most popular in today?s consumer electronics industry

A low hardware complexity time domain quantizer for wideband multibit - ADCs

This paper presents proof of concept of a low hardware complexity time domain quantizer (TDQ) for wideband multibit countinuous time (CT) ΣΔ ADCs. Besides rendering multi-level quantization of the input signal, the proposed scheme generates a two-level loop feedback signal for the modulator. The two-level feedback eliminates the errors emanating from component mismatches in the feedback digital-to-analog converter (DAC) due to process variations. The complete scheme is modeled using Simulink (MATLAB) and is validated through simulation. A 2nd order ΣΔ modulator incorporating the proposed TDQ achieves a dynamic range of 45.7 dB for a bandwidth of 10 MHz and an input sine-wave of -5.78 dBFS amplitude

Digital enhancement techniques for data converters in scaled CMOS technologies

This thesis presents digital enhancement techniques for data converters in advanced technology nodes. With technology scaling, traditional voltage-domain (VD) analog-to-digital converters (ADCs) face two major challenges: (1) reduction of dynamic range due to supply voltage scaling, and (2) decrease in intrinsic gain of transistors which makes high gain amplifier design tough. To address these challenges, a two-stage ADC architecture is presented which uses time-domain quantization to exploit the advantages of technology scaling. The architecture, consisting of a first stage successive approximation register (SAR) and a second stage ring oscillator, is highly digital and scaling friendly. Two prototypes have been developed to validate the proposed architecture. The 40nm CMOS prototype achieves 75.7 dB dynamic range at an excellent Schreier figure-of-merit of 172.2 dB. The proposed architecture has been extended to a capacitance-to-digital converter and a prototype has been developed in 40nm CMOS. The prototype can sense capacitances with a resolution of 1.3fF and has a Walden figure-of-merit of 60 fJ/step which is more than two times better than the current state-of-the-art. This thesis also presents digital techniques to improve performance of continuous-time(CT), delta-sigma digital-to-analog converters (DACs). Recently, CT delta-sigma DACs have received more attention than their discrete, switched-capacitor counterpart mainly because of low power and/or higher speed of operation. However, a critical disadvantage of CT, delta-sigma DACs is their greatly increased sensitivity to inter-symbol interference (ISI) error. To address this shortcoming of CT DACs, this thesis presents several algorithms that can mitigate ISI error simultaneously with static mismatch error. Further, the proposed algorithms are fully digital in nature and as such, are best poised to take maximum advantage of technology scaling. Thus, the techniques presented in this thesis will be important enabling factors in raising the envelope of performance of CT delta-sigma DACs in advanced technology nodes.Electrical and Computer Engineerin

Enhanced-accuracy oversampled data converters

Digital-to-analog converters (DACs) suffer from static and dynamic nonlinearity problems, which degrade their accuracy and performance. Mismatch errors in the analog components restrict the maximum achievable linearity. This thesis presents various techniques for correcting these errors. It describes a correction process for the nonlinear behavior of DACs, on three different levels: architectural design, circuit design, and layout design. The main results achieved are listed below: • Novel topologies using stochastic approaches to linearize multibit converters are presented. • A new method is introduced for avoiding the use of multibit DACs in the main loop of multi-path DS analog-to-digital converters (ADCs), which, combined with a novel noise leakage compensation technique, allows the use of low quality inner DACs. • A novel correction algorithm is proposed, which is based on the acquisition of the individual DAC errors by means of correlation procedures. The extracted values are used for correction purposes. The technique is capable of background operation. • Different circuits are proposed to improve the performance of current-steering DACs. Also, novel layout techniques are shown for reducing the spatial variations of the unit sources. Some of the presented techniques were combined in a prototype chip, designed and fabricated in a 0.35μm CMOS process. Simulation and preliminary measurement results show that they are effective.Keywords: data converters, digital-to-analog, integrated circuits, analog-to-digital, CMO

Arquiteturas paralelas avançadas para transmissores 5G totalmente digitais

The fifth generation of mobile communications (5G) is being prepared and should be rolled out in the early coming years. Massive number of Radio-Frequency (RF) front-ends, peak data rates of 10 Gbps (everywhere and everytime), latencies lower than 10 msec and huge device densities are some of the expected disruptive capabilities. At the same time, previous generations can not be jeopardized, fostering the design of novel flexible and highly integrated radio transceivers able to support the simultaneous transmission of multi-band and multi-standard signals. The concept of all-digital transmission is being pointed out as a promising architecture to cope with such challenging requirements, due to its fully digital radio datapath. This thesis is focused on the proposal and validation of fully integrated and advanced digital transmitter architectures that excel the state-of-the-art in different figures of merit, such as transmission bandwidth, spectral purity, carrier agility, flexibility, and multi-band capability. The first part of this thesis introduces the concept of all-digital RF transmission. In particular, the foundations inherent to this thematic line are given, together with the recent advances reported in the state-of-the-art architectures.The core of this thesis, containing the main developments achieved during the Ph.D. work, is then presented and discussed. The first key contribution to the state-of-the-art is the use of cascaded Delta-Sigma (∆Σ) architectures to relax the analog filtering requirements of the conventional All-Digital Transmitters while maintaining the constant envelope waveform. Then, it is presented the first reported architecture where Antenna Arrays are directly driven by single-chip and single-bit All-Digital Transmitters, with promising results in terms of simplification of the RF front-ends and overall flexibility. Subsequently, the thesis proposes the first reported RF-stage All-Digital Transmitter that can be embedded within a single Field-Programmable Gate Array (FPGA) device. Thereupon, novel techniques to enable the design of wideband All-Digital Transmitters are reported. Finally, the design of concurrent multi-band transmitters is introduced. In particular, the design of agile and flexible dual and triple bands All-DigitalTransmitter (ADT) is demonstrated, which is a very important topic for scenarios that demand carrier aggregation. This Ph.D. contributes withseveral advances to the state-of-the-art of RF all-digital transmitters.A quinta geração de comunicações móveis (5G) está a ser preparada e deve ser comercializada nos próximos anos. Algumas das caracterı́sticas inovadoras esperadas passam pelo uso de um número massivo de font-ends de Rádio-Frequência (RF), taxas de pico de transmissão de dados de 10 Gbps (em todos os lugares e em todas as ocasiões), latências inferiores a 10 mseg e elevadas densidades de dispositivos. Ao mesmo tempo, as gerações anteriores não podem ser ignoradas, fomentando o design de novos transceptores de rádio flexı́veis e altamente integrados, capazes de suportar a transmissão simultânea de sinais multi-banda e multi-standard. O conceito de transmissão totalmente digital é considerado como um tipo de arquitetura promissora para lidar com esses requisitos desafiantes, devido ao seu datapath de rádio totalmente digital. Esta tese é focada na proposta e validação de arquiteturas de transmissores digitais totalmente integradas e avançadas que ultrapassam o estado da arte em diferentes figuras de mérito, como largura de banda de transmissão, pureza espectral, agilidade de portadora, flexibilidade e capacidade multibanda. A primeira parte desta tese introduz o conceito de transmissores de RF totalmente digitais. Em particular, os fundamentos inerentes a esta linha temática são apresentados, juntamente com os avanços mais recentes do estado-da-arte. O núcleo desta tese, contendo os principais desenvolvimentos alcançados durante o trabalho de doutoramento, é então apresentado e discutido. A primeira contribuição fundamental para o estado da arte é o uso de arquiteturas em cascata com moduladores ∆Σ para relaxar os requisitos de filtragem analógica dos transmissores RF totalmente digitais convencionais, mantendo a forma de onda envolvente constante. Em seguida, é apresentada a primeira arquitetura em que agregados de antenas são excitados diretamente por transmissores digitais de um único bit inseridos num único chip, com resultados promissores em termos de simplificação dos front-ends de RF e flexibilidade em geral. Posteriormente, é proposto o primeiro transmissor totalmente digital RF-stage relatado que pode ser incorporado dentro de um único Agregado de Células Lógicas Programáveis. Novas técnicas para permitir o desenho de transmissores RF totalmente digitais de banda larga são também apresentadas. Finalmente, o desenho de transmissores simultâneos de múltiplas bandas é exposto. Em particular, é demonstrado o desenho de transmissores de duas e três bandas ágeis e flexı́veis, que é um tópico essencial para cenários que exigem agregação de múltiplas bandas.Apoio financeiro da Fundação para a Ciência e Tecnologia (FCT) no âmbito de uma bolsa de doutoramento, ref. PD/BD/105857/2014.Programa Doutoral em Telecomunicaçõe

High Performance Integrated Circuit Blocks for High-IF Wideband Receivers

Due to the demand for high‐performance radio frequency (RF) integrated circuit design in the past years, a system‐on‐chip (SoC) that enables integration of analog and digital parts on the same die has become the trend of the microelectronics industry. As a result, a major requirement of the next generation of wireless devices is to support multiple standards in the same chip‐set. This would enable a single device to support multiple peripheral applications and services. Based on the aforementioned, the traditional superheterodyne front‐end architecture is not suitable for such applications as it would require a complete receiver for each standard to be supported. A more attractive alternative is the highintermediate frequency (IF) radio architecture. In this case the signal is digitalized at an intermediate frequency such as 200MHz. As a consequence, the baseband operations, such as down‐conversion and channel filtering, become more power and area efficient in the digital domain. Such architecture releases the specifications for most of the front‐end building blocks, but the linearity and dynamic range of the ADC become the bottlenecks in this system. The requirements of large bandwidth, high frequency and enough resolution make such ADC very difficult to realize. Many ADC architectures were analyzed and Continuous‐Time Bandpass Sigma‐Delta (CT‐BP‐ΣΔ) architecture was found to be the most suitable solution in the high‐IF receiver architecture since they combine oversampling and noise shaping to get fairly high resolution in a limited bandwidth. A major issue in continuous‐time networks is the lack of accuracy due to powervoltage‐ temperature (PVT) tolerances that lead to over 20% pole variations compared to their discrete‐time counterparts. An optimally tuned BP ΣΔ ADC requires correcting for center frequency deviations, excess loop delay, and DAC coefficients. Due to these undesirable effects, a calibration algorithm is necessary to compensate for these variations in order to achieve high SNR requirements as technology shrinks. In this work, a novel linearization technique for a Wideband Low‐Noise Amplifier (LNA) targeted for a frequency range of 3‐7GHz is presented. Post‐layout simulations show NF of 6.3dB, peak S21 of 6.1dB, and peak IIP3 of 21.3dBm, respectively. The power consumption of the LNA is 5.8mA from 2V. Secondly, the design of a CMOS 6th order CT BP‐ΣΔ modulator running at 800 MHz for High‐IF conversion of 10MHz bandwidth signals at 200 MHz is presented. A novel transconductance amplifier has been developed to achieve high linearity and high dynamic range at high frequencies. A 2‐bit quantizer with offset cancellation is alsopresented. The sixth‐order modulator is implemented using 0.18 um TSMC standard analog CMOS technology. Post‐layout simulations in cadence demonstrate that the modulator achieves a SNDR of 78 dB (~13 bit) performance over a 14MHz bandwidth. The modulator’s static power consumption is 107mW from a supply power of ± 0.9V. Finally, a calibration technique for the optimization of the Noise Transfer Function CT BP ΣΔ modulators is presented. The proposed technique employs two test tones applied at the input of the quantizer to evaluate the noise transfer function of the ADC, using the capabilities of the Digital Signal Processing (DSP) platform usually available in mixed‐mode systems. Once the ADC output bit stream is captured, necessary information to generate the control signals to tune the ADC parameters for best Signal‐to‐Quantization Noise Ratio (SQNR) performance is extracted via Least‐ Mean Squared (LMS) software‐based algorithm. Since the two tones are located outside the band of interest, the proposed global calibration approach can be used online with no significant effect on the in‐band content

Design Techniques for High-Performance SAR A/D Converters

The design of electronics needs to account for the non-ideal characteristics of the device technologies used to realize practical circuits. This is particularly important in mixed analog-digital design since the best device technologies are very different for digital compared to analog circuits. One solution for this problem is to use a calibration correction approach to remove the errors introduced by devices, but this adds complexity and power dissipation, as well as reducing operation speed, and so must be optimised. This thesis addresses such an approach to improve the performance of certain types of analog-to-digital converter (ADC) used in advanced telecommunications, where speed, accuracy and power dissipation currently limit applications. The thesis specifically focuses on the design of compensation circuits for use in successive approximation register (SAR) ADCs. ADCs are crucial building blocks in communication systems, in general, and for mobile networks, in particular. The recently launched fifth generation of mobile networks (5G) has required new ADC circuit techniques to meet the higher speed and lower power dissipation requirements for 5G technology. The SAR has become one of the most favoured architectures for designing high-performance ADCs, but the successive nature of the circuit operation makes it difficult to reach ∼GS/s sampling rates at reasonable power consumption. Here, two calibration techniques for high-performance SAR ADCs are presented. The first uses an on-chip stochastic-based mismatch calibration technique that is able to accurately compute and compensate for the mismatch of a capacitive DAC in a SAR ADC. The stochastic nature of the proposed calibration method enables determination of the mismatch of the CAPDAC with a resolution much better than that of the DAC. This allows the unit capacitor to scale down to as low as 280aF for a 9-bit DAC. Since the CAP-DAC causes a large part of the overall dynamic power consumption and directly determines both the sizes of the driving and sampling switches and the size of the input capacitive load of the ADC and the kT/C noise power, a small CAP-DAC helps the power efficiency. To validate the proposed calibration idea, a 10-bit asynchronous SAR ADC was fabricated in 28-nm CMOS. Measurement results show that the proposed stochastic calibration improves the ADC’s SFDR and SNDR by 14.9 dB, 11.5 dB, respectively. After calibration, the fabricated SAR ADC achieves an ENOB of 9.14 bit at a sampling rate of 85 MS/s, resulting in a Walden FoM of 10.9 fJ/c-s. The second calibration technique is a timing-skew calibration for a time-interleaved (TI) SAR ADC that calibrates/computes the inter-channel timing and offset mismatch simultaneously. Simulation results show the effectiveness of this calibration method. When used together, the proposed mismatch calibration technique and the timing-skew calibration technique enables a TI SAR ADC to be designed that can achieve a sampling rate of ∼GS/s with 10-bit resolution and a power consumption as low as ∼10mW; specifications that satisfy the requirements of 5G technology