A 5 GHz Direct Digital Synthesizer MMIC with Direct Modulation and Spur Randomization

Abstract-This paper presents a low power, ultra high speed and high resolution SiGe DDS MMIC with 24-bit phase and 10-bit amplitude resolution. The DDS MMIC has the capabilities of direct frequency and phase modulations with 24 bit and 12 bit resolution, respectively. It is the first reported mm-wave DDS with direct digital frequency and phase modulation capabilities. Utilizing a 13-bit built-in ultra high speed pseudorandom binary sequence (PRBS) generator, the DDS MMIC can perform least significant bit (LSB) dithering for spur randomization. With more than twenty thousand transistors, the DDS MMIC includes a 24-bit ripple carry accumulator for phase accumulation, a 12-bit ripple carry adder for phase modulation, an LSB dithering block for spur randomization and a 10-bit segmented sine-weighted DAC for phase to amplitude mapping and digital to analog conversion. The DDS core occupies 3.0×2.5 mm 2 and consumes 4.7 W power under a single 3.3 V power supply. The Nyquist band SFDR is measured as 38 dBc with 469.360351 MHz output under 5.0 GHz maximum clock (FCW = 0x180800). With 1.246258914 GHz output frequency (FCW = 0x3FCFE7), the narrow band SFDR is measured as 82 dBc. The DDS MMIC is packaged and tested in LCC-68 cavity. Index Terms-digital-to-analog converter (DAC), direct digital synthesizer (DDS), direct digital frequency synthesizer (DDFS), sine-weighted digital-to-analog converter, Rom-less DDS, frequency modulation (FM), phase modulation (PM

Design and characterization of monolithic millimeter-wave active and passive components, low-noise and power amplifiers, resistive mixers, and radio front-ends

This thesis focuses on the design and characterization of monolithic active and passive components, low-noise and power amplifiers, resistive mixers, and radio front-ends for millimeter-wave applications. The thesis consists of 11 publications and an overview of the research area, which also summarizes the main results of the work. In the design of millimeter-wave active and passive components the main focus is on realized CMOS components and techniques for pushing nanoscale CMOS circuits beyond 100 GHz. Test structures for measuring and analyzing these components are shown. Topologies for a coplanar waveguide, microstrip line, and slow-wave coplanar waveguide that are suitable for implementing transmission lines in nanoscale CMOS are presented. It is demonstrated that the proposed slow-wave coplanar waveguide improves the performance of the transistor-matching networks when compared to a conventional coplanar waveguide and the floating slow-wave shield reduces losses and simplifies modeling when extended below other passives, such as DC decoupling and RF short-circuiting capacitors. Furthermore, wideband spiral transmission line baluns in CMOS at millimeter-wave frequencies are demonstrated. The design of amplifiers and a wideband resistive mixer utilizing the developed components in 65-nm CMOS are shown. A 40-GHz amplifier achieved a +6-dBm 1-dB output compression point and a saturated output power of 9.6 dBm with a miniature chip size of 0.286 mm². The measured noise figure and gain of the 60-GHz amplifier were 5.6 dB and 11.5 dB, respectively. The V-band balanced resistive mixer achieved a 13.5-dB upconversion loss and 34-dB LO-to-RF isolation with a chip area of 0.47 mm². In downconversion, the measured conversion loss and 1-dB input compression point were 12.5 dB and +5 dBm, respectively. The design and experimental results of low-noise and power amplifiers are presented. Two wideband low-noise amplifiers were implemented in a 100-nm metamorphic high electron mobility transistor (HEMT) technology. The amplifiers achieved a 22.5-dB gain and a 3.3-dB noise figure at 94 GHz and a 18-19-dB gain and a 5.5-7.0-dB noise figure from 130 to 154 GHz. A 60-GHz power amplifier implemented in a 150-nm pseudomorphic HEMT technology exhibited a +17-dBm 1-dB output compression point with a 13.4-dB linear gain. In this thesis, the main system-level aspects of millimeter-wave transmitters and receivers are discussed and the experimental circuits of a 60-GHz transmitter front-end and a 60-GHz receiver with an on-chip analog-to-digital converter implemented in 65-nm CMOS are shown. The receiver exhibited a 7-dB noise figure, while the saturated output power of the transmitter front-end was +2 dBm. Furthermore, a wideband W-band transmitter front-end with an output power of +6.6 dBm suitable for both image-rejecting superheterodyne and direct-conversion transmission is demonstrated in 65-nm CMOS

Integration of broadband direct-conversion quadrature modulators

To increase spectral efficiency, transmitters usually send only one of the information carrying sidebands centered around a single radio-frequency carrier. The close-lying mirror, or image, sideband will be eliminated either by the filtering method or by the phasing method. Since filter Q-values rise in direct relation to the transmitted frequencies, the filtering method is generally not feasible for integrated microwave transmitters. A quadrature modulator realizes the phasing method by combining signals phased at quadrature (i.e. at 90° offsets) to produce a single-sideband (SSB) output. In this way output filtering can be removed or its specifications greatly relieved so as to produce an economical microwave transmitter. The proliferation of integrated circuit (IC) technologies since the 1980s has further boosted the popularity of quadrature modulator as an IC realization makes possible the economical production of two closely matched doubly balanced mixers, which suppress carrier and even-order spurious leakage to circuit output. Another strength of IC is its ability to perform microwave quadrature generation accurately on-chip, and thereby to avoid most of the interconnect parasitics which could ruin high-frequency quadrature signaling. Nevertheless, all quadrature modulator implementations are sensitive to phasing and amplitude errors, which are born as a result of mismatches, from the use of inaccurate differential signaling, and from inadequacies in the phasing circuitry itself. A 2° phase error is easily produced, and it reduces the image-rejection ratio (IRR) to −30 dBc. Therefore, as baseband signals synthesized by digital signal processing (DSP) are sufficiently accurate, this thesis concentrates on analyzing and producing the microwave signal path of a direct-conversion quadrature modulator with special emphasis on broadband, multimode radio-compatible operation. A model of the direct-conversion quadrature modulator operation has been developed, which reveals the effect the circuit non-linearities and mismatch-related offsets have on available performance. Further, theoretical proof is given of the well-known property of improving differential signal balance that cascaded differential pairs exhibit. Among the practical results, a current reuse mixer has been developed, which improves the transmitted signal-to-noise-ratio (SNR) by 3 dB, with a maximum measured dynamic range of +158 dB. The complementary bipolar process was further used to extend the bipolar push-pull stage bandwidth to 9.5 GHz. At the core of this work is the parallel switchable polyphase (PP) filter quadrature generator that was developed, since it makes possible accurate broadband IQ generation without the high loss that usually results from the application of PP filtering. Two IQ modulator prototypes were realized to test simulated and theoretically derived data: the 0.8 µm SiGe IC achieves an IRR better than −40 dBc over 0.75-3.6 GHz, while the 0.13 µm digital bulk CMOS IC achieves better than −37 dBc over 0.56-4.76 GHz. For this IRR performance the SiGe prototype boasts the inexpensive solution of integrated baluns, while the CMOS one utilizes a coil-transmission line hybrid transformer at its LO input to drive the switchable PP filters.Taajuuksien käytön tehostamiseksi lähettimet lähettävät yleensä vain toisen informaatiota sisältävistä sivukaistoistaan yhdelle radiotaajuuksiselle kantoaallolle keskitettynä. Viereinen peilitaajuus eli sivukaista vaimennetaan joko suodattamalla tai vaiheistamalla signalointia sopivasti. Koska suodattimen hyvyysluvut nousevat suorassa suhteessa käytettyyn taajuuteen, ei suodatusmenetelmä ole yleensä mahdollinen mikroaaltotaajuusalueen lähettimissä. Kvadratuurimodulaattori toteuttaa vaiheistusmenetelmän yhdistämällä 90-asteen vaihesiirroksin vaiheistetut signaalit yksisivukaistaisen lähetteen tuottamiseksi. Näin voidaan korvata lähdön suodatus joko kokonaan tai lieventämällä vaadittavia suoritusarvoja, jolloin mikroaaltoalueen lähetin voidaan tuottaa taloudellisesti. Integroitujen piiriratkaisujen yleistyminen 1980-luvulta lähtien on edesauttanut kvadratuurimodulaattorin suosiota, koska integroidulle piirille voidaan taloudellisesti tuottaa kaksi hyvin ominaisuuksiltaan toisiaan vastaavaa kaksoisbalansoitua sekoitinta, ja nämä tunnetusti vaimentavat kantoaaltovuotoa ja parillisia harmoonisia piirin lähdössä. Toinen integroitujen piirien vahvuus on kyky tarkkaan mikroaaltoalueen kvadratuurisignalointiin samalla piirillä, jolloin vältetään suurin osa kytkentöjen parasiittisista jotka muutoin voisivat tuhota korkeataajuuksisen 90-asteen vaiheistuksen. Kaikki kvadratuurimodulaattorit ovat joka tapauksessa herkkiä vaiheistus- ja amplitudieroille, joita syntyy komponenttiarvojen satunnaishajonnasta, epätarkan differentiaalisen signaloinnin käytöstä, ja itse vaiheistuspiiristön puutteellisuuksista. Kahden asteen vaihevirhe syntyy helposti, ja tällöin sivukaistavaimennus heikkenee -30 dBc:n tasolle. Tämänvuoksi, ja olettaen että digitaalisella signaaliprosessorilla luotu kantataajuuksinen signalointi on riittävän tarkkaa, tämä väitöskirja keskittyy kvadratuurimodulaattorin mikroaaltotaajuuksisen signaalipolun analysointiin ja tuottamiseen painottaen erityisesti laajakaistaista, monisovellusradioiden kanssa yhteensopivaa toimivuutta. Kvadratuurimodulaattorin toimintamallia on kehitetty siten, että mallissa huomioidaan epälineaarisuuksien ja piirielementtien satunnaishajontojen vaikutus saavutettavalle suorituskyvylle. Lisäksi on teoreettisesti todistettu sinänsä hyvin tunnettu peräkkäin kytkettyjen vahvistinasteiden differentiaalisen signaloinnin symmetrisyyttä parantava vaikutus. Käytännön tuloksista voidaan mainita kehitetty virtaakierrättävä sekoitin, joka parantaa signaali-kohinasuhdetta +3 dB, suurimman mitatun dynaamisen alueen ollessa +158 dB. Samaa komplementaarista bipolaariprosessia käytettiin edelleen bipolaarisen vuorovaihe-asteen kaistan levittämisessä 9.5 GHz:iin. Yhtenä tämän työn tärkeimmistä tuloksista on kehitetty kytkimin valittavista rinnakkaisista monivaihesuodattimista koostuva kvadratuurigeneraattori, jolla on mahdollista tuottaa laajakaistaista IQ-signalointia ilman suurta häviötä joka yleensä liittyy monivaihesuodattimien käyttöön. Kaksi IQ-modulaattoriprototyyppiä toteutettiin simuloitujen ja teoreettisesti mallinnettujen tulosten testaamiseksi: 0.8 µm SiGe integroitu piiri saavuttaa paremman sivukaistavaimennuksen kuin -40 dBc yli 0.75-3.6 GHz, kun taas 0.13 µm digitaalipiirien tuottamiseen tarkoitetulla CMOS prosessilla toteutettu integroitu piiri saavuttaa paremman sivukaistavaimennuksen kuin -37 dBc taajuusalueella 0.56-4.76 GHz. Näihin sivukaistavaimennuksiin SiGe prototyyppi pääsee edullisesti integroiduin symmetrointimuuntajin, kun taas CMOS piirillä käytetään kela-siirtojohto-tyyppistä yhdistelmämuuntajaa LO-sisääntulossa josta ajetaan erikseen kytkettäviä monivaihesuodattimia.reviewe

A 5 GHz BiCMOS I/Q VCO with 360° variable phase outputs using the vector sum method

This research looks into the design of an integrated in-phase/quadrature (I/Q) VCO operating at 5 GHz. The goal is to design a phase shifter that is implemented at the LO used for RF up conversion. The target application for the phase shifter is towards phased array antennas operating at 5 GHz. Instead of designing multiple VCOs that each deliver a variety of phases, two identical LC-VCOs are coupled together to oscillate at the same frequency and deliver four outputs that are 90 ° out of phase. By varying the amplitudes of the in-phase and quadrature signals independently using VGAs before adding them together, a resultant out-of-phase signal is obtained. A number of independently variable out-of-phase signals can be obtained from these 90 ° out-of-phase signals and this technique is better known as the vector sum method of phase shifting. Control signals to the inputs of the VGAs required to obtain 22.5 ° phase shifts were designed from simulations and are generated using 16-bit DACs. The design is implemented and manufactured using a 0.35 µm SiGe BiCMOS process and the complete prototype IC occupies an area of 2.65 × 2.65 mm2. The I/Q VCO with 360 ° variable phase outputs occupies 1.10 × 0.85 mm2 of chip area and the 16-bit DAC along with its decoding circuitry occupies 0.41 × 0.13 mm2 of chip area. The manufactured quadrature VCO was found to oscillate between 4.12 ~ 4.74 GHz and consumes 23.1 mW from a 3.3 V supply without its buffer circuitry. A maximum phase noise of -78.5 dBc / Hz at a 100 kHz offset and -108.17 dBc / Hz at a 1 MHz offset was measured and the minimum VCO figure of merit is 157.8 dBc / Hz. The output voltages of the 16 bit DAC are within 3.5 % of the design specifications. When the phase shifter is controlled by the 16 DAC signals, the maximum measured phase error of the phase shifter is lower than 10 %.Dissertation (MEng)--University of Pretoria, 2009.Electrical, Electronic and Computer Engineeringunrestricte

Lithium niobate RF-MEMS oscillators for IoT, 5G and beyond

This dissertation focuses on the design and implementation of lithium niobate (LiNbO3) radiofrequency microelectromechanical (RF-MEMS) oscillators for internet-of-things (IoT), 5G and beyond. The dissertation focuses on solving two main problems found nowadays in most of the published works: the narrow tuning range and the low operating frequency (sub 3 GHz) acoustic oscillators currently deliver. The work introduced here enables wideband voltage-controlled MEMS oscillators (VCMOs) needed for emerging applications in IoT. Moreover, it enables multi-GHz (above 8 GHz) RF-MEMS oscillators through harnessing over mode resonances for 5G and beyond. LiNbO3 resonators characterized by high-quality factor (Q), high electromechanical coupling (kt2), and high figure-of-merit (FoMRES= Q kt2) are crucial for building the envisioned high-performance oscillators. Those oscillators can be enabled with lower power consumption, wider tuning ranges, and a higher frequency of oscillation when compared to other state-of-the-art (SoA) RF-MEMS oscillators. Tackling the tuning range issue, the first VCMO based on the heterogeneous integration of a high Q LiNbO3 RF-MEMS resonator and complementary metal-oxide semiconductor (CMOS) is demonstrated in this dissertation. A LiNbO3 resonator array with a series resonance of 171.1 MHz, a Q of 410, and a kt2 of 12.7% is adopted, while the TSMC 65 nm RF LP CMOS technology is used to implement the active circuitry with an active area of 220×70 µm2. Frequency tuning of the VCMO is achieved by programming a binary-weighted digital capacitor bank and a varactor that are both connected in series to the resonator. The measured best phase noise performances of the VCMO are -72 and -153 dBc/Hz at 1 kHz and 10 MHz offsets from 178.23 and 175.83 MHz carriers, respectively. The VCMO consumes a direct current (DC) of 60 µA from a 1.2 V supply while realizing a tuning range of 2.4 MHz (~ 1.4% tuning range). Such VCMOs can be applied to enable ultralow-power, low phase noise, and wideband RF synthesis for emerging applications in IoT. Moreover, the first VCMO based on LiNbO3 lateral overtone bulk acoustic resonator (LOBAR) is demonstrated in this dissertation. The LOBAR excites over 30 resonant modes in the range of 100 to 800 MHz with a frequency spacing of 20 MHz. The VCMO consists of a LOBAR in a closed-loop with two amplification stages and a varactor-embedded tunable LC tank. By the bias voltage applied to the varactor, the tank can be tuned to change the closed-loop gain and phase responses of the oscillator so that Barkhausen’s conditions are satisfied for the targeted resonant mode. The tank is designed to allow the proposed VCMO to lock to any of the ten overtones ranging from 300 to 500 MHz. These ten tones are characterized by average Qs of 2100, kt2 of 1.5%, FoMRES of 31.5 enabling low phase noise, and low-power oscillators crucial for IoT. Owing to the high Qs of the LiNbO3 LOBAR, the measured VCMO shows a close-in phase noise of -100 dBc/Hz at 1 kHz offset from a 300 MHz carrier and a noise floor of -153 dBc/Hz while consuming 9 mW. With further optimization, this VCMO can lead to direct RF synthesis for ultra-low-power transceivers in multi-mode IoT nodes. Tackling the multi-GHz operation problem, the first Ku-band RF-MEMS oscillator utilizing a third antisymmetric overtone (A3) in a LiNbO3 resonator is presented in the dissertation. Quarter-wave resonators are used to satisfy Barkhausen’s oscillation conditions for the 3rd overtone while suppressing the fundamental and higher-order resonances. The oscillator achieves measured phase noise of -70 and -111 dBc/Hz at 1 kHz and 100 kHz offsets from a 12.9 GHz carrier while consuming 20 mW of dc power. The oscillator achieves a FoMOSC of 200 dB at 100 kHz offset. The achieved oscillation frequency is the highest reported to date for a MEMS oscillator. In addition, this dissertation introduces the first X-band RF-MEMS oscillator built using CMOS technology. The oscillator consists of an acoustic resonator in a closed loop with cascaded RF tuned amplifiers (TAs) built on TSMC RF GP 65 nm CMOS. The TAs bandpass response, set by on-chip inductors, satisfies Barkhausen's oscillation conditions for A3 only. Two circuit variations are implemented. The first is an 8.6 GHz standalone oscillator with a source-follower buffer for direct 50 Ω-based measurements. The second is an oscillator-divider chain using an on-chip 3-stage divide-by-2 frequency divider for a ~1.1 GHz output. The standalone oscillator achieves measured phase noise of -56, -113, and -135 dBc/Hz at 1 kHz, 100 kHz, and 1 MHz offsets from an 8.6 GHz output while consuming 10.2 mW of dc power. The oscillator also attains a FoMOSC of 201.6 dB at 100 kHz offset, surpassing the SoA electromagnetic (EM) and RF-MEMS based oscillators. The oscillator-divider chain produces a phase noise of -69.4 and -147 dBc/Hz at 1 kHz and 1 MHz offsets from a 1075 MHz output while consuming 12 mW of dc power. Its phase noise performance also surpasses the SoA L-band phase-locked loops (PLLs). The demonstrated performance shows the strong potential of microwave acoustic oscillators for 5G frequency synthesis and beyond. This work will enable low-power 5G transceivers featuring high speed, high sensitivity, and high selectivity in small form factors

CMOS Integrated Circuit Design for Ultra-Wideband Transmitters and Receivers

Ultra-wideband technology (UWB) has received tremendous attention since the FCC license release in 2002, which expedited the research and development of UWB technologies on consumer products. The applications of UWB range from ground penetrating radar, distance sensor, through wall radar to high speed, short distance communications. The CMOS integrated circuit is an attractive, low cost approach for implementing UWB technology. The improving cut-off frequency of the transistor in CMOS process makes the CMOS circuit capable of handling signal at multi-giga herz. However, some design challenges still remain to be solved. Unlike regular narrow band signal, the UWB signal is discrete pulse instead of continuous wave (CW), which results in the occupancy of wide frequency range. This demands that UWB front-end circuits deliver both time domain and frequency domain signal processing over broad bandwidth. Witnessing these technique challenges, this dissertation aims at designing novel, high performance components for UWB signal generation, down-conversion, as well as accurate timing control using low cost CMOS technology. We proposed, designed and fabricated a carrier based UWB transmitter to facilitate the discrete feature of the UWB signal. The transmitter employs novel twostage -switching to generate carrier based UWB signal. The structure not only minimizes the current consumption but also eliminates the use of a UWB power amplifier. The fabricated transmitter is capable of delivering tunable UWB signal over the complete 3.1GHz -10.6GHz UWB band. By applying the similar two-stage switching approach, we were able to implement a novel switched-LNA based UWB sampling receiver frontend. The proposed front-end has significantly lower power consumption compared to previously published design while keep relatively high gain and low noise at the same time. The designed sampling mixer shows unprecedented performance of 9-12dB voltage conversion gain, 16-25dB noise figure, and power consumption of only 21.6mW(with buffer) and 11.7mW(without buffer) across dc to 3.5GHz with 100M-Hz sampling frequency. The implementation of a precise delay generator is also presented in the dissertation. It relies on an external reference clock to provide accurate timing against process, supply voltage and temperature variation through a negative feedback loop. The delay generator prototype has been verified having digital programmability and tunable delay step resolution. The relative delay shift from desired value is limited to within 0.2%

ANALYSIS AND DESIGN OF SILICON-BASED MILLIMETER-WAVE AMPLIFIERS

Ph.DDOCTOR OF PHILOSOPH

Reconfigurable high efficiency class-F power amplifier using CMOS-MEMS technology

The increasing demand for wireless products to be part of our daily lives brings the need for longer battery lifetime, smaller size and lower cost. To increase battery lifetime, high efficiency power amplifiers (PAs) are needed; To make them smaller, integration or reconfiguration is aimed and to reach lower costs, technologies such as CMOS are final goals. However integration of high efficiency PA in CMOS is challenging due to the technology limitations which restricts the achievable output power and efficiency of the PA. In order to bring solutions for the above-mentioned requirements, in this thesis novel reconfigurable class-F PAs, frequency-reconfiguration, CMOS integration, impedance-reconfiguration and CMOS-MEMS implementation are addressed. Starting with a single frequency operation, a novel class-F PA for mobile applications is proposed in which with a proper harmonic tuning structure the need for extra filtering sections is eliminated, achieving an excellent harmonic-suppression level. This topology uses transmission lines and is developed to cover multiple frequency bands for purpose of global coverage with aim of size reduction. Three novel frequency reconfigurable PAs are proposed using MEMS and semiconductor switches to accomplish class-F operation at two frequencies. The main novelty of this structure is that the reconfiguration is done not only at fundamental frequency but also at harmonics with reduced number of tuning elements. Moreover, by proper placement of the switches in the stubs, the maximum voltages over the switches are minimized. The proposed structure overcomes the narrow band performance of class-F, giving an efficiency more than 60% over a 225 MHz and 175 MHz bandwidth at 900 MHz and 1800 MHz respectively. Measurement results showed high performance at both frequency bands giving 69.5% and 57.9% PAE at 900 MHz and 1800 MHz respectively. A novel CMOS class-F PA is proposed that controls up to the 3rd harmonic and can adapt to load variations due to the effect of the human body on mobile phones. It enables the integration of the PA with other devices in a single chip leading to better matching, higher performance, lower cost and smaller size. In addition, it achieves load impedance reconfigurability by using impedance tuner in its output network and by proper tuning of the network, effects of load variation on the performance are compensated. Two designs at 2.4 GHz have been done using either MOS varactors or MEMS variable capacitors as tuning devices. The design using MOS varactors show a maximum measured values of 26% PAE and 19.2 dBm output power for 50 load. For loads other than 50 ohm an improvement of 15% for PAE and 4.4 dB for output power is obtained in comparison to non-tuned one. The second design is done using MEMS variable capacitors integrated in CMOS technology through a mask-less post-processing technique. Simulations results for 50 ohm load show a peak PAE of 32.8% while delivering 18.2 dBm output power.La creixent demanda de productes sense fils en la nostra vida diària requereix dispositius de menor grandària, menor cost i amb una gran autonomia. Per reduir la mida i augmentar l'autonomia és necessari utilitzar sistemes integrats multiestàndard o reconfigurables, amb amplificadors de RF d'alta eficiència, mentre que per reduir el cost, és preferible utilitzar tecnologies econòmiques com CMOS. No obstant això, la integració en CMOS d'amplificadors de radiofreqüència, i en especial, d'alta eficiència, és un repte a causa de les limitacions de la tecnologia que restringeixen la potència de sortida realitzable i l'eficiència de l'amplificador. En aquesta tesi es tracten els diferents reptes anteriorment esmentats, proposant una nova topologia d'amplificador classe-F amb reconfiguració de freqüència, i proposant la integració d'un amplificador classe-F que s¿adapta a impedància de càrrega variable, implementat en CMOS i CMOS-MEMS. Inicialment en la tesi es proposa una topologia d'amplificador classe-F en què, gràcies a una estructura adequada a la xarxa d'adaptació, s¿elimina la necessitat de filtrat extra, aconseguint un nivell de rebuig d'harmònics excel·lent. La topologia proposada utilitza línies de transmissió i s'ha desenvolupat per dues bandes diferents, amb el disseny orientat a implementar un sistema reconfigurable. S'han aconseguit PAE de l'ordre del 80 % amb potències properes a 10 W. Un cop descrita i analitzada la topologia, s'han proposat tres amplificadors reconfigurables per doble banda freqüencial. Per a la reconfiguració s'han utilitzat MEMS i commutadors basats en semiconductors. L'estructura proposada permet la reconfiguració no només en la freqüència fonamental sinó també en els harmònics, però mantenint un nombre reduït d'elements d'ajust. A més, gràcies a l'adequada col·locació dels commutadors en les línies de transmissió, s'ha minimitzat la tensió màxima en els mateixos. Així mateix, l'estructura proposada evita la característica de banda estreta a classe-F, proporcionant una eficiència superior al 60% en unes amplades de banda de 225 MHz i de 175 MHz, per a les banda de 900 MHz i 1800 MHz respectivament. En aquestes bandes, la PAE màxima mesurada és del 69,5% i del 57,9% respectivament. Finalment, s'ha proposat un amplificador integrat en CMOS, classe-F amb control fins al tercer harmònic. L'amplificador proposat incorpora un sintonitzador a la sortida, podent així adaptar-se a variacions d'impedància de càrrega, típiques en dispositius sense fil (WLAN), degudes a l'efecte del cos humà sobre l'antena. La implementació en CMOS permet la integració de l'amplificador de potència amb altres dispositius en un únic xip, donant lloc a una millor adaptació, millor rendiment, menor cost i menor grandària del sistema. A més, gràcies a l'adaptació a les variacions de la impedància de càrrega, permet mantenir el rendiment en diferents rangs d'operació. S'han realitzat dos dissenys de l'amplificador a 2,4 GHz, un basat en varactors MOS i un altre en condensadors variables MEMS. El disseny que utilitza varactors MOS mostra una PAE màxima del 26% i una potència de 19,2 dBm per a càrrega adaptada 50 ohm. Per altres càrregues, gràcies a l'adaptació d'impedància, s'obté una millora de PAE del 15% i de 4,4 dB en potència de sortida. El disseny utilitzant condensadors MEMS s'integra en CMOS gràcies a post-processat sense màscares addicionals. Els resultats de simulació per a 50 ohm mostren una PAE del 32,8% per 18,2 dBm de potència de sortid