Digitally-Assisted RF IC Design Techniques for Reliable Performance

Semiconductor industries have competitively scaled down CMOS devices to attain benefits of low cost, high performance, and high integration density in digital integrated circuits. On the other hand, deep scaled technologies inextricably accompany a large process variation, supply voltage scaling, and reduction in breakdown voltages of transistors. When it comes to RF/analog IC design, CMOS scaling adversely affects its reliability due to large performance variation and limited linearity. For addressing the issues related to variations and linearity, this research proposes the following digitally-assisted RF circuit design techniques: self-calibration system for RF phase shifters and wide dynamic range LNAs. Due to PVT variations in scaled technologies, RF phase shifter design becomes more challenging with device scaling. In the proposed self-calibration topology, we devised a novel phase sensing method and a pulsewidth-to-digital converter. The feedback controller is also designed in digital domain, which is robust to PVT variations. These unique techniques enable a sensing/control loop tolerant to PVT variations. The self-calibration loop was applied to a 7 to 13GHz phase shifter. With the calibration, the estimated phase error is less than 2 degrees. To overcome the linearity issue in scaled technologies, a digitally-controlled dual-mode LNA design is presented. A narrowband (5.1GHz) and a wideband (0.8 to 6GHz) LNA can be toggled between high-gain and high-linearity modes by digital control bits according to the input signal power. A compact design, which provides negligible performance degradation by additional circuitry, is achieved by sharing most of the components between the two operation modes. The narrowband and the wideband LNA achieves an input-referred P1dB of -1.8dBm and +4.2dBm, respectively

RF Amplification and Filtering Techniques for Cellular Receivers

The usage of various wireless standards, such as Bluetooth, Wi-Fi, GPS, and 4G/5G cellular, has been continually increasing. In order to utilize the frequency bands efficiently and to support new communication standards with lower power consumption, lower occupied volume and at reduced costs, multimode transceivers, software defined radios (SDRs), cognitive radios, etc., have been actively investigated. Broadband behavior of a wireless receiver is typically defined by its front-end low-noise amplifier (LNA), whose design must consider trade-offs between input matching, noise figure (NF), gain, bandwidth, linearity, and voltage headroom in a given process technology. Moreover, monolithic RF wireless receivers have been trending toward high intermediatefrequency (IF) or superhetrodyne radios thanks to recent breakthroughs in silicon integration of band-pass channel-select filters. The main motivation is to avoid the common issues in the currently predominant zero/low-IF receivers, such as poor 2nd-order nonlinearity, sensitivity to 1/f (i.e. flicker) noise and time-variant dc offsets, especially in the fine CMOS technology. To avoid interferers and blockers at the susceptible image frequencies that the high-IF entails, band-pass filters (BPF) with high quality (Q) factor components for sharp transfer-function transition characteristics are now required. In addition, integrated low-pass filters (LPF) with strong rejection of out-of-band frequency components are essential building blocks in a variety of applications, such as telecommunications, video signal processing, anti-aliasing filtering, etc. Attention is drawn toward structures featuring low noise, small area, high in-/out-of-band linearity performance, and low-power consumption. This thesis comprises three main parts. In the first part (Chapters 2 and 3), we focus on the design and implementation of several innovative wideband low-noise (transconductance) amplifiers [LN(T)A] for wireless cellular applications. In the first design, we introduce new approaches to reduce the noise figure of the noise-cancellation LNAs without sacrificing the power consumption budget, which leads to NF of 2 dB without adding extra power consumption. The proposed LNAs also have the capability to be used in current-mode receivers, especially in discrete-time receivers, as in the form of low noise transconductance amplifier (LNTA). In the second design, two different two-fold noise cancellation approaches are proposed, which not only improve the noise performance of the design, but also achieve high linearity (IIP3=+4.25 dBm). The proposed LN(T)As are implemented in TSMC 28-nm LP CMOS technology to prove that they are suitable for applications such as sub-6 GHz 5G receivers. The second objective of this dissertation research is to invent a novel method of band-pass filtering, which leads to achieving very sharp and selective band-pass filtering with high linearity and low input referred (IRN) noise (Chapter 4). This technique improves the noise and linearity performance without adding extra clock phases. Hence, the duty cycle of the clock phases stays constant, despite the sophisticated improvements. Moreover, due to its sharp filtering, it can filter out high blockers of near channels and can increase the receiver’s blocker tolerance. With the same total capacitor size and clock duty cycle as in a 1st-order complex charge-sharing band-pass filter (CS BPF), the proposed design achieves 20 dB better out-of-band filtering compared to the prior-art 1st-order CS BPF and 10 dB better out-of-band filtering compared to the conventional 2nd-order C-CS BPF. Finally, the stop-band rejection of the discrete-time infinite-impulse response (IIR) lowpass filter is improved by applying a novel technique to enhance the anti-aliasing filtering (Chapter 5). The aim is to introduce a 4th-order charge rotating (CR) discrete-time (DT) LPF, which achieves the record of stop-band rejection of 120 dB by using a novel pseudolinear interpolation technique while keeping the sampling frequency and the capacitor values constant

Radiofrequency architectures and technologies for software defined radio

Six-port network is an interesting radiofrequency architecture with multiple possibilities. Since it was firstly introduced in the seventies as an alternative network analyzer, the six-port network has been used for many applications, such as homodyne receivers, radar systems, direction of arrival estimation, UWB (Ultra-Wide-Band), or MIMO (Multiple Input Multiple Output) systems. Currently, it is considered as a one of the best candidates to implement a Software Defined Radio (SDR). This thesis comprises an exhaustive study of this promising architecture, where its fundamentals and the state-of-the-art are also included. In addition, the design and development of a SDR 0.3-6 GHz six-port receiver prototype is presented in this thesis, which is implemented in conventional technology. The system is experimentally characterized and validated for RF signal demodulation with good performance. The analysis of the six-port architecture is complemented by a theoretical and experimental comparison with other radiofrequency architectures suitable for SDR. Some novel contributions are introduced in the present thesis. Such novelties are in the direction of the highly topical issues on six-port technique: development and optimization of real-time I-Q regeneration techniques for multiport networks; and search of new techniques and technologies to contribute to the miniaturization of the six-port architecture. In particular, the novel contributions of this thesis can be summarized as: - Introduction of a new real-time auto-calibration method for multiport receivers, particularly suitable for broadband designs and high data rate applications. - Introduction of a new direct baseband I-Q regeneration technique for five-port receivers. - Contribution to the miniaturization of six-port receivers by the use of the multilayer LTCC (Low Temperature Cofired Ceramic) technology. Implementation of a compact (30x30x1.25 mm) broadband (0.3-6 GHz) six-port receiver in LTTC technology. The results and conclusions derived from this thesis have been satisfactory, and quite fruitful in terms of publications. A total of fourteen works have been published, considering international journals and conferences, and national conferences. Aditionally, a paper has been submitted to an internationally recognized journal, which is currently under review

Switched-Capacitor RF Receivers for High Interferer Tolerance

The demand for broadband wireless communication is growing rapidly, requiring more spectrum resources. However, spectrum usage is inefficient today because different frequency bands are allocated for different communication standards and most of the bands are not highly occupied. Cognitive radio systems with dynamic spectrum access improve spectrum efficiency, but they require wideband tunable receiver hardware. In such a system, a preselect filter is required for the RF receiver front end, because an out-of-band (OB) interferer can block the front end or cause distortion, desensitizing the receiver. In a conventional solution, off-chip passive filters, such as surface-acoustic-wave (SAW) filters, are used to reject the OB interferer. However, such passive filters are hardly tunable, have large area, and are very expensive. On-chip, high-selectivity, linearly tunable RF filters are, therefore, a hot topic in RF front-end research. Switched-capacitor (SC) RF filters, such as N-path filters, feature good linearity and tunability, making them good candidates for tunable RF filters. However, N-path filters have some drawbacks: notably, a poor harmonic response and limited close-by blocker tolerance. This thesis presents the design and implementation of several interferer-tolerant receivers based on SC technology. We present an RF receiver with a harmonic-rejecting N-path filter to improve the harmonic response of the N-path bandpass filter. It features tunable narrowband filtering and high attenuation of the third- and fifth-order LO harmonics at the LNA output, which improves the blocker tolerance at LO harmonics. The 0.2-1 GHz RF receiver is implemented in a 65 nm CMOS process. The blocker 1 dB compression point (B1dB) is -2.4 dBm at a 20 MHz offset, and remains high at the third- and fifth-order LO harmonics. The LNA’s reverse isolation helps keep the LO emission below -90 dBm. A two-stage harmonic-rejection approach offers a > 51 dB harmonic-rejection ratio at the third- and fifth-order LO harmonics without calibration. To improve tolerance for close-by blockers, we further present an SC RF receiver achieving high-order, tunable, highly linear RF filtering. We implement RF input impedance matching, N-path filtering, high-order discrete-time infinite-impulse response (IIR) filtering and downconversion using only switches and capacitors in a 0.1-0.7 GHz prototype with tunable center frequency, programmable filter order, and very high tolerance for OB blockers. The 40 nm CMOS receiver consumes 38.5-76.5mA, achieves 40 dB gain, 24 dBm OB IIP3, 14.7 dBm B1dB for a 30MHz blocker offset, 6.8-9.7 dB noise figure, and > 66dB calibrated harmonic rejection ratio. The key drawback of our earlier SC receiver is the relatively high theoretical lower limit of the noise figure. To improve the noise performance, we developed a 0.1-0.6 GHz chopping SC RF receiver with an integrated blocker detector. We achieve RF impedance matching, high-order OB interferer filtering, and flicker-noise chopping with passive SC circuits only. The 34-80 mW 65 nm receiver achieves 35 dB gain, 4.6-9 dB NF, 31 dBm OB-IIP3, and 15 dBm B1dB. The 0.2 mW integrated blocker detector detects large OB blockers with only a 1 us response time. The filter order can be adapted to blocker power with the blocker detector

Vidutinių dažnių 5G belaidžių tinklų galios stiprintuvų tyrimas

This dissertation addresses the problems of ensuring efficient radio fre-quency transmission for 5G wireless networks. Taking into account, that the next generation 5G wireless network structure will be heterogeneous, the device density and their mobility will increase and massive MIMO connectivity capability will be widespread, the main investigated problem is formulated – increasing the efficiency of portable mid-band 5G wireless network CMOS power amplifier with impedance matching networks. The dissertation consists of four parts including the introduction, 3 chapters, conclusions, references and 3 annexes. The investigated problem, importance and purpose of the thesis, the ob-ject of the research methodology, as well as the scientific novelty are de-fined in the introduction. Practical significance of the obtained results, defended state-ments and the structure of the dissertation are also included. The first chapter presents an extensive literature analysis. Latest ad-vances in the structure of the modern wireless network and the importance of the power amplifier in the radio frequency transmission chain are de-scribed in detail. The latter is followed by different power amplifier archi-tectures, parameters and their improvement techniques. Reported imped-ance matching network design methods are also discussed. Chapter 1 is concluded distinguishing the possible research vectors and defining the problems raised in this dissertation. The second chapter is focused around improving the accuracy of de-signing lumped impedance matching network. The proposed methodology of estimating lumped inductor and capacitor parasitic parameters is dis-cussed in detail provi-ding complete mathematical expressions, including a summary and conclusions. The third chapter presents simulation results for the designed radio fre-quency power amplifiers. Two variations of Doherty power amplifier archi-tectures are presented in the second part, covering the full step-by-step de-sign and simulation process. The latter chapter is concluded by comparing simulation and measurement results for all designed radio frequency power amplifiers. General conclusions are followed by an extensive list of references and a list of 5 publications by the author on the topic of the dissertation. 5 papers, focusing on the subject of the discussed dissertation, have been published: three papers are included in the Clarivate Analytics Web of Sci-ence database with a citation index, one paper is included in Clarivate Ana-lytics Web of Science database Conference Proceedings, and one paper has been published in unreferred international conference preceedings. The au-thor has also made 9 presentations at 9 scientific conferences at a national and international level.Dissertatio

Time and Frequency Transfer in a Coherent Multistatic Radar using a White Rabbit Network

Networks of coherent multistatic radars require accurate and stable time and frequency transfer (TFT) for range and Doppler estimation. TFT techniques based on global navigation satellite systems (GNSS), have been favoured for several reasons, such as enabling node mobility through wireless operation, geospatial referencing, and atomic clock level time and frequency stability. However, such systems are liable to GNSS-denial, where the GNSS carrier is temporarily or permanently removed. A denial-resilient system should consider alternative TFT techniques, such as the White Rabbit (WR) project. WR is an Ethernet based protocol, that is able to synchronise thousands of nodes on a fibre-optic based network with sub-nanosecond accuracy and picoseconds of jitter. This thesis evaluates WR as the TFT network for a coherent multistatic pulse-Doppler radar – NeXtRAD. To test the hypothesis that WR is suitable for TFT in a coherent multistatic radar, the time and frequency performance of a WR network was evaluated under laboratory conditions, comparing the results against a network of multi-channel GPS-disciplined oscillators (GPSDO). A WR-disciplined oscillator (WRDO) is introduced, which has the short-term stability of an ovenised crystal (OCXO), and long-term stability of the WR network. The radar references were measured using a dual mixer time difference technique (DMTD), which allows the phase to be measured with femtosecond level resolution. All references achieved the stringent time and frequency requirements for short-term coherent bistatic operation, however the GPSDOs and WRDOs had the best short-term frequency stability. The GPSDOs had the highest amount of long-term phase drift, with a peak-peak time error of 9.6 ns, whilst the WRDOs were typically stable to within 0.4 ns, but encountered transient phase excursions to 1.5 ns. The TFT networks were then used on the NeXtRAD radar, where a lighthouse, Roman Rock, was used as a static target to evaluate the time and frequency performance of the references on a real system. The results conform well to the laboratory measurements, and therefore, WR can be used for TFT in coherent radar

Multiple beam antenna/switch system study

In the study of the Multiple Beam Antenna/Switch for the space to ground link (SGL) uplink and downlink services, several issues related to system engineering, antenna, transmit/receive, and switch systems were addressed and the results are provided. Bandwidth allocation at Ku band is inadequate to serve the data rate requirements for the forward and return services. Rain and depolarization effects at EHF, especially at Ka band, pose a significant threat to the link availabilities at heavy rain areas. Hardware induced effects such as the nonlinear characteristics of the power amplifier may necessitate the use of linearizers and limiters. It is also important to identify the components that are susceptible to the space radiation effects and shield or redesign them with rad-hard technologies for meeting the requirements of the space environment

Advances in Solid State Circuit Technologies

This book brings together contributions from experts in the fields to describe the current status of important topics in solid-state circuit technologies. It consists of 20 chapters which are grouped under the following categories: general information, circuits and devices, materials, and characterization techniques. These chapters have been written by renowned experts in the respective fields making this book valuable to the integrated circuits and materials science communities. It is intended for a diverse readership including electrical engineers and material scientists in the industry and academic institutions. Readers will be able to familiarize themselves with the latest technologies in the various fields