Design of Inverter Based CMOS Amplifiers in Deep Nanoscale Technologies

In this work, it is proposed a fully differential ring amplifier topology with a deadzone voltage created by a CMOS resistor with a biasing circuit to increase the robustness over PVT variations. The study focuses on analyzing the performance of the ring amplifier over process, temperature, and supply voltage variations, in order to guarantee a viable industrial employment in a 7 nm FinFET CMOS technology node for being used as residue amplifier in ADCs. A ring amplifier is a small modular amplifier, derived from a ring oscillator. It is simple enough that it can quickly be designed using only a few inverters, capacitors, and switches. It can amplify with rail-to-rail output swing, competently charge large capacitive loads using slew-based charging, and scale well in performance according to process trends. In typical process corner, a gain of 72 dB is achieved with a settling time of 150 ps. Throughout the study, the proposed topology is compared with others presented in literature showing better results over corners and presenting a faster response. The proposed topology isn’t yet suitable for industry use, because it presents one corner significantly slower than the rest, namely process corner FF 125 °C, and process corner FS -40 °C with a small oscillation throughout the entire amplification period. Nevertheless, it proved itself to be a promising technique, showing a high gain and a fast settling without oscillation phase, with room for improvement.Neste trabalho, é proposta uma topologia de ring amplifier com a deadzone a ser criada através de uma resistência CMOS com um circuito de polarização para aumentar a robustez para as variações PVT. O estudo foca-se em analisar a performance do ring amplifier nas variações de processo, temperatura e tensão de alimentação, de forma a garantir um uso viável em indústria na tecnologia de 7 nm FinFET CMOS, para ser usado como amplificador de resíduo em ADCs. Um ring amplifier é um pequeno amplificador modular, derivado do ring oscillator. É simples o suficiente para ser facilmente projetado usando apenas poucos inversores, condensadores e interruptores. Consegue amplificar com rail-to-rail output swing, carregar grandes cargas capacitivas com carregamento slew-based e escalar bem em termos de performance de acordo com o processo. No typical process corner, foi obtido um ganho de 72 dB com um tempo de estabilização de 150 ps. Durante o estudo, a topologia proposta é comparada com outras presentes na literatura mostrando melhores resultados over corners e apresentando uma resposta mais rápida. A topologia proposta ainda não está preparada para uso industrial uma vez que apresenta um corner significativamente mais lento que os restantes, nomeadamente, process corner FF 125 °C, e outro process corner, FS -40 °C, com uma pequena oscilação durante todo o período de amplificação. Todavia, provou ser uma técnica promissora, apresentando um ganho elevado e uma rápida estabilização sem fase de oscilação, com espaço para melhoria

Modeling and analysis of power processing systems: Feasibility investigation and formulation of a methodology

A review is given of future power processing systems planned for the next 20 years, and the state-of-the-art of power processing design modeling and analysis techniques used to optimize power processing systems. A methodology of modeling and analysis of power processing equipment and systems has been formulated to fulfill future tradeoff studies and optimization requirements. Computer techniques were applied to simulate power processor performance and to optimize the design of power processing equipment. A program plan to systematically develop and apply the tools for power processing systems modeling and analysis is presented so that meaningful results can be obtained each year to aid the power processing system engineer and power processing equipment circuit designers in their conceptual and detail design and analysis tasks

Integrated circuits for efficient power delivery using pulse-width-modulation

Circuits and architectures for efficient power delivery have become crucial in emerging smart systems. Switching power amplifiers (PA) are very attractive for such applications, because they exhibit better efficiency compared to linear PA designs, due to saturated operation. Switching PAs also allow for utilization of deep submicron CMOS technologies, due to which these designs can be easily integrated with digital circuits, and can benefit from process scaling, in performance as well as in area. Pulse-width-modulation (PWM) is commonly used with switching PAs. A PWM signal typically employs a high-frequency switching pulse waveform as a carrier signal, wherein the pulse-width or duty-cycle of each pulse is modulated by a given low-frequency input signal. The carrier frequency can vary from several kHz to GHz, and is typically determined by the target application. In this thesis, efficient power-delivery circuits that use PWM with switching class-D stages are presented. Advanced circuit techniques, as well as architectures for PWM are proposed to enhance efficiency and circumvent the limitations of conventional architectures. A digitally-intensive transmitter using RF-PWM with a class-D PA is described in the first part of the thesis. The use of carrier switching for alleviating the dynamic range limitation that can be observed in classical RF-PWM implementations is introduced. The approach employs the full carrier frequency for half of the amplitude range, and the second harmonic of half of the carrier frequency, for the remainder of the amplitude range. This concept not only allows the transmitter to drive modulated signals with large peak-to-average power ratio (PAPR), but also improves the back-off efficiency due to reduced switching losses in the half carrier-frequency mode. A glitch-free phase selector is proposed that removes the deleterious glitches that can occur at the input data transitions. The phase-selector also prevents D flip-flop setup-and-hold time violations. The transmitter has been implemented in a 130-nm CMOS process. The measured peak output power and power-added-efficiency (PAE) are 25.6 dBm and 34%, respectively. While driving 802.11g 20-MHz 64-QAM OFDM signals, the average measured output power is 18.3 dBm and the PAE is 16%, with an EVM of -25.5 dB. The second part of the thesis describes a high-speed driver that provides a PWM output using a class-D PA. A PLL-based architecture is employed which eliminates the requirement for a precise ramp or triangular signal generator, and a high-speed comparator, which are typically used for PWM generation. Multi-level signaling is proposed to enhance back-off as well as peak efficiency, which is critical for signals with high PAPR. A differential, folded PWM scheme is introduced to achieve highly linear operation. 3-level operation is achieved without the requirement for additional supply source or sink paths, while 5-level operation is achieved with additional supply source and sink paths, compared to 2-level operation. The PWM driver has been implemented in a 130-nm CMOS process and can operate with a switching frequency of 40-to-170 MHz. For 2/3/5-level PA operation, with a 500 kHz sinusoidal input and 60 MHz switching frequency, the measured THD is -61/-62/-53 dB and corresponding efficiency is 71/83/86% with 175/200/220 mW output power level, respectively. Performance has also been verified for 2/3-level PA operation with a high PAPR signal with 500 kHz bandwidth. While intended as a general purpose amplifier, the approach is well-suited for applications such as power-line communications (PLC). The final part of the thesis introduces an efficient buck/buck-boost reconfigurable LED driver that supports PWM and PFM operation. The driver is based on peak current control. Rectified sin as well as sin² functions are employed in the reference signal to improve the power factor (PF) and total harmonic distortion (THD) of the buck and buck-boost converters. The design ensures that the peak of the inductor current maintains a constant level that is invariant for different AC line voltages. The operating mode of the design can be changed between PWM and PFM. The LED driver has been implemented in a 130-nm CMOS process. PF and THD are improved when the proposed reference is employed, and peak PF and lowest THD are 0.995/0.983/0.996 and 7.8/6.2/3.5% for the buck (PWM), buck (PFM), buck-boost (PFM) cases, respectively. The corresponding peak efficiency for the three cases is 88/92/91%, respectively.Electrical and Computer Engineerin

A wideband supply modulator for 20MHz RF bandwidth polar PAs in 65nm CMOS

A wideband modulator for a 20MHz bandwidth polar modulated PA is presented which achieves a maximum efficiency of 87.5% and a small signal -3dB bandwidth of 285MHz. Realized in 65nm CMOS, it consists of a cascoded nested Miller compensated linear amplifier and a class D switching amplifier. It can deliver 22.7dBm output power to a 5.3Ω load. With a switching frequency of 118MHz, the output switching ripple is 4.3mVrms. Keywords: supply modulator, power amplifier, CMOS and cascoded nested Miller

Class D Audio Amplifier

This project consisted of the design, construction, and comparison testing of two implementations of analog pulse-width modulation Class D audio amplifiers. The main goal of the project was to maximize the efficiency of the amplifier designs while maintaining a high-power, low-noise output signal. PCB testing confirmed that the amplifiers met our goals of greater than 90% efficiency, less than 1% total harmonic distortion and greater than 50 W output power

Third order CMOS decimator design for sigma delta modulators

A third order Cascaded Integrated Comb (CIC) filter has been designed in 0.5μm n-well CMOS process to interface with a second order oversampling sigma-delta ADC modulator. The modulator was designed earlier in 0.5μm technology. The CIC filter is designed to operate with 0 to 5V supply voltages. The modulator is operated with ±2.5V supply voltage and a fixed oversampling ratio of 64. The CIC filter designed includes integrator, differentiator blocks and a dedicated clock divider circuit, which divides the input clock by 64. The CIC filter is designed to work with an ADC that operates at a maximum oversampling clock frequency of up to 25 MHz and with baseband signal bandwidth of up to 800 kHz. The design and performance of the CIC filter fabricated has been discussed