메모리 인터페이스를 위한 멀티 레벨 단일 종단 송신기 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·컴퓨터공학부, 2020. 8. 김수환.본 연구에서 메모리 인터페이스를 위한 멀티 레벨 송신기가 제시되었다. 프로세서와 메모리 간의 성능 차이가 매년 계속 증가함에 따라, 메모리는 전체 시스템의 병목점이 되고있다. 우리는 메모리 대역폭을 늘리기 위해 PAM-4 단일 종단 송신기를 제안하였고, 멀티 랭크 메모리를 위한 duobinary 단일 종단 송신기를 제안하였다. 제안된 PAM-4 송신기의 드라이버는 높은 선형성과 임피던스 정합을 동시에 만족한다. 또한 저항이나 인덕터를 사용하지 않아 작은 면적을 차지한다. 제안된 ZQ 캘리브레이션은 세개의 교정 점을 가지고 있어 송신기가 정확한 임피던스와 선형적인 출력을 갖게 한다. 프로토 타입은 65nm CMOS 공정으로 제작되었고 송신기는 0.0333mm2의 면적을 차지한다. 측정된 28Gb/s에서의 eye는 18.3ps의 길이와 42.4mV의 높이를 갖고, 에너지 효율은 0.64pJ/bit이다. ZQ 캘리브레이션과 함께 측정된 RLM은 0.993이다. 메모리의 용량을 늘리기 위해 하나의 패키지에 여러 개의 DRAM 다이를 수직으로 쌓는 패키징은 메모리의 중앙 패드 구조와 결합되어 짧은 반사를 야기하는 스텁을 만든다. 우리는 이 문제를 완화하기위해 반사 기반 duobinary 송신기를 제안했다. 이 송신기는 반사를 이용하여 duobinary signaling을 한다. 2탭 반대 강조 기술과 슬루 레이트 조절 기술이 신호 완결성을 높이기 위해 사용되었다. NRZ eye가 없는 10Gb/s에서 측정된 duobinary eye는 63.6ps 길이와 70.8mV의 높이를 갖는다. 측정된 에너지 효율은 1.38pJ/bit이다.Multi-level transmitters for memory interfaces have been presented. The performance gap between processor and memory has been increased by 50% every year, making memory to be a bottle neck of the overall system. To increase memory bandwidth, we have proposed a PAM-4 single-ended transmitter. To compensate for the side effect of the multi-rank memory, we have proposed a reflection-based duobinary transmitter. The proposed PAM-4 transmitter has the driver, which simultaneously satisfies impedance matching and high linearity. The driver occupies a small area due to a resistorless and inductorless structure. The proposed ZQ calibration for PAM-4 has three calibration points, which allow the transmitter to have accurate impedance and linear output. The ZQ calibration considers impedance variation of both the driver and the receiver. A prototype has been fabricated in 65nm CMOS process, and the transmitter occupies 0.0333mm2. The measured eye has a width of 18.3ps and a height of 42.4mV at 28Gb/s, and the measured energy efficiency is 0.64pJ/b. The measured RLM with the 3-point ZQ calibration is 0.993. To increase memory density, the stacked die packaging with multiple DRAM die stacked vertically in one package is widely used. However, combined with the center-pad structure, the structure creates stubs that cause short reflections. We have proposed the reflection-based duobinary transmitter to mitigate this problem. The proposed transmitter uses reflection for duobinary signaling. The 2-tap opposite FFE and the slew-rate control are used to increase signal integrity. The measured duobinary eye at 10Gb/s has a width of 63.6ps and a height of 70.8mV while there is no NRZ eye opening. The measured energy efficiency is 1.38pJ/bit.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 8 CHAPTER 2 MUTI-LEVEL SIGNALING 9 2.1 PAM-4 SIGNALING 9 2.2 DESIGN CONSIDERATIONS FOR PAM-4 TRANSMITTER 16 2.2.1 LEVEL SEPARATION MISMATCH RATIO (RLM) 17 2.2.2 IMPEDANCE MATCHING 19 2.2.3 PRIOR ARTS 21 2.3 DUOBINARY SIGNALING 24 CHAPTER 3 HIGH-LINEARITY AND IMPEDANCE-MATCHED PAM-4 TRANSMITTER 30 3.1 OVERALL ARCHITECTURE 31 3.2 SINGLE-ENDED IMPEDANCE-MATCHED PAM-4 DRIVER 33 3.3 3-POINT ZQ CALIBRATION FOR PAM-4 47 CHAPTER 4 REFLECTION-BASED DUOBINARY TRANSMITTER 57 4.1 BIDIRECTIONAL DUAL-RANK MEMORY SYSTEM 58 4.2 CONCEPT OF REFLECTION-BASED DUOBINARY SIGNALING 66 4.3 REFLECTION-BASED DUOBINARY TRANSMITTER 70 4.3.1 OVERALL ARCHITECTURE 70 4.3.2 EQUALIZATION FOR REFLECTION-BASED DUOBINARY SIGNALING 72 4.3.3 2D BINARY-SEGMENTED DRIVER 75 CHAPTER 5 EXPERIMENTAL RESULTS 77 5.1 HIGH-LINEARITY AND IMPEDANCE-MATCHED PAM-4 TRANSMITTER 77 5.2 REFLECTION-BASED DUOBINARY TRANSMITTER 84 CHAPTER 6 92 CONCLUSION 92 BIBLIOGRAPHY 94Docto

Design Techniques for High Pin Efficiency Wireline Transceivers

While the majority of wireline research investigates bandwidth improvement and how to overcome the high channel loss, pin efficiency is also critical in high-performance wireline applications. This dissertation proposes two different implementations for high pin efficiency wireline transceivers. The first prototype achieves twice pin efficiency than unidirectional signaling, which is 32Gb/s simultaneous bidirectional transceiver supporting transmission and reception on the same channel at the same time. It includes an efficient low-swing voltage-mode driver with an R-gm hybrid for signal separation, combining the continuous-time-linear-equalizer (CTLE) and echo cancellation (EC) in a single stage, and employing a low-complexity 5/4X CDA system. Support of a wide range of channels is possible with foreground adaptation of the EC finite impulse response (FIR) filter taps with a sign-sign least-mean-square (SSLMS) algorithm. Fabricated in TSMC 28-nm CMOS, the 32Gb/s SBD transceiver occupies $0.09 mm^{2}$ area and achieves 16Gb/s uni-directional and 32Gb/s simultaneous bi-directional signals. 32Gb/s SBD operation consumes 1.83mW/Gb/s with 10.8dB channel loss at Nyquist rate. The second prototype presents an optical transmitter with a quantum-dot (QD) microring laser. This can support wavelength-division multiplexing allowing for high pin efficiency application by packing multiple high-bandwidth signals onto one optical channel. The development QD microring laser model accurately captures the intrinsic photonic high-speed dynamics and allows for the future co-design of the circuits and photonic device. To achieve higher bandwidth than intrinsic one, utilizing both techniques of optical injection locking (OIL) and 2-tap asymmetric Feed-forward equalizer (FFE) can perform 22Gb/s operation with 3.2mW/Gb/s. The first hybrid-integration directly-modulated OIL QD microring laser system is demonstrated

Hybrid NRZ/Multi-Tone Signaling for High-Speed Low-Power Wireline Transceivers

Over the past few decades, incessant growth of Internet networking traffic and High-Performance Computing (HPC) has led to a tremendous demand for data bandwidth. Digital communication technologies combined with advanced integrated circuit scaling trends have enabled the semiconductor and microelectronic industry to dramatically scale the bandwidth of high-loss interfaces such as Ethernet, backplane, and Digital Subscriber Line (DSL). The key to achieving higher bandwidth is to employ equalization technique to compensate the channel impairments such as Inter-Symbol Interference (ISI), crosstalk, and environmental noise. Therefore, todayâs advanced input/outputs (I/Os) has been equipped with sophisticated equalization techniques to push beyond the uncompensated bandwidth of the system. To this end, process scaling has continually increased the data processing capability and improved the I/O performance over the last 15 years. However, since the channel bandwidth has not scaled with the same pace, the required signal processing and equalization circuitry becomes more and more complicated. Thereby, the energy efficiency improvements are largely offset by the energy needed to compensate channel impairments. In this design paradigm, re-thinking about the design strategies in order to not only satisfy the bandwidth performance, but also to improve power-performance becomes an important necessity. It is well known in communication theory that coding and signaling schemes have the potential to provide superior performance over band-limited channels. However, the choice of the optimum data communication algorithm should be considered by accounting for the circuit level power-performance trade-offs. In this thesis we have investigated the application of new algorithm and signaling schemes in wireline communications, especially for communication between microprocessors, memories, and peripherals. A new hybrid NRZ/Multi-Tone (NRZ/MT) signaling method has been developed during the course of this research. The system-level and circuit-level analysis, design, and implementation of the proposed signaling method has been performed in the frame of this work, and the silicon measurement results have proved the efficiency and the robustness of the proposed signaling methodology for wireline interfaces. In the first part of this work, a 7.5 Gb/s hybrid NRZ/MT transceiver (TRX) for multi-drop bus (MDB) memory interfaces is designed and fabricated in 40 nm CMOS technology. Reducing the complexity of the equalization circuitry on the receiver (RX) side, the proposed architecture achieves 1 pJ/bit link efficiency for a MDB channel bearing 45 dB loss at 2.5 GHz. The measurement results of the first prototype confirm that NRZ/MT serial data TRX can offer an energy-efficient solution for MDB memory interfaces. Motivated by the satisfying results of the first prototype, in the second phase of this research we have exploited the properties of multi-tone signaling, especially orthogonality among different sub-bands, to reduce the effect of crosstalk in high-dense wireline interconnects. A four-channel transceiver has been implemented in a standard CMOS 40 nm technology in order to demonstrate the performance of NRZ/MT signaling in presence of high channel loss and strong crosstalk noise. The proposed system achieves 1 pJ/bit power efficiency, while communicating over a MDB memory channel at 36 Gb/s aggregate data rate

An Energy-Efficient Reconfigurable Mobile Memory Interface for Computing Systems

The critical need for higher power efficiency and bandwidth transceiver design has significantly increased as mobile devices, such as smart phones, laptops, tablets, and ultra-portable personal digital assistants continue to be constructed using heterogeneous intellectual properties such as central processing units (CPUs), graphics processing units (GPUs), digital signal processors, dynamic random-access memories (DRAMs), sensors, and graphics/image processing units and to have enhanced graphic computing and video processing capabilities. However, the current mobile interface technologies which support CPU to memory communication (e.g. baseband-only signaling) have critical limitations, particularly super-linear energy consumption, limited bandwidth, and non-reconfigurable data access. As a consequence, there is a critical need to improve both energy efficiency and bandwidth for future mobile devices.;The primary goal of this study is to design an energy-efficient reconfigurable mobile memory interface for mobile computing systems in order to dramatically enhance the circuit and system bandwidth and power efficiency. The proposed energy efficient mobile memory interface which utilizes an advanced base-band (BB) signaling and a RF-band signaling is capable of simultaneous bi-directional communication and reconfigurable data access. It also increases power efficiency and bandwidth between mobile CPUs and memory subsystems on a single-ended shared transmission line. Moreover, due to multiple data communication on a single-ended shared transmission line, the number of transmission lines between mobile CPU and memories is considerably reduced, resulting in significant technological innovations, (e.g. more compact devices and low cost packaging to mobile communication interface) and establishing the principles and feasibility of technologies for future mobile system applications. The operation and performance of the proposed transceiver are analyzed and its circuit implementation is discussed in details. A chip prototype of the transceiver was implemented in a 65nm CMOS process technology. In the measurement, the transceiver exhibits higher aggregate data throughput and better energy efficiency compared to prior works

Adaptive Receiver Design for High Speed Optical Communication

Conventional input/output (IO) links consume power, independent of changes in the bandwidth demand by the system they are deployed in. As the system is designed to satisfy the peak bandwidth demand, most of the time the IO links are idle but still consuming power. In big data centers, the overall utilization ratio of IO links is less than 10%, corresponding to a large amount of energy wasted for idle operation. This work demonstrates a 60 Gb/s high sensitivity non-return-to-zero (NRZ) optical receiver in 14 nm FinFET technology with less than 7 ns power-on time. The power on time includes the data detection, analog bias settling, photo-diode DC current cancellation, and phase locking by the clock and data recovery circuit (CDR). The receiver autonomously detects the data demand on the link via a proposed link protocol and does not require any external enable or disable signals. The proposed link protocol is designed to minimize the off-state power consumption and power-on time of the link. In order to achieve high data-rate and high-sensitivity while maintaining the power budget, a 1-tap decision feedback equalization method is applied in digital domain. The sensitivity is measured to be -8 dBm, -11 dBm, and -13 dBm OMA (optical modulation amplitude) at 60 Gb/s, 48 Gb/s, and 32 Gb/s data rates, respectively. The energy efficiency in always-on mode is around 2.2 pJ/bit for all data-rates with the help of supply and bias scaling. The receiver incorporates a phase interpolator based clock-and-data recovery circuit with approximately 80 MHz jitter-tolerance corner frequency, thanks to the low-latency full custom CDR logic design. This work demonstrates the fastest ever reported CMOS optical receiver and runs almost at twice the data-rate of the state-of-the-art CMOS optical receiver by the time of the publication. The data-rate is comparable to BiCMOS optical receivers but at a fraction of the power consumption

WDM/TDM PON bidirectional networks single-fiber/wavelength RSOA-based ONUs layer 1/2 optimization

This Thesis proposes the design and the optimization of a hybrid WDM/TDM PON at the L1 (PHY) and L2 (MAC) layers, in terms of minimum deployment cost and enhanced performance for Greenfield NGPON. The particular case of RSOA-based ONUs and ODN using a single-fibre/single-wavelength is deeply analysed. In this WDM/TDM PON relevant parameters are optimized. Special attention has been given at the main noise impairment in this type of networks: the Rayleigh Backscattering effect, which cannot be prevented. To understand its behaviour and mitigate its effects, a novel mathematical model for the Rayleigh Backscattering in burst mode transmission is presented for the first time, and it has been used to optimize the WDM/TDM RSOA based PON. Also, a cost-effective, simple design SCM WDM/TDM PON with rSOA-based ONU, was optimized and implemented. This prototype was successfully tested showing high performance, robustness, versatility and reliability. So, the system is able to give coverage up to 1280 users at 2.5 Gb/s / 1.25 Gb/s downstream/upstream, over 20 Km, and being compatible with the GPON ITU-T recommendation. This precedent has enabled the SARDANA network to extend the design, architecture and capabilities of a WDM/TDM PON for a long reach metro-access network (100 km). A proposal for an agile Transmission Convergence sub-layer is presented as another relevant contribution of this work. It is based on the optimization of the standards GPON and XG-PON (for compatibility), but applied to a long reach metro-access TDM/WDM PON rSOA-based network with higher client count. Finally, a proposal of physical implementation for the SARDANA layer 2 and possible configurations for SARDANA internetworking, with the metro network and core transport network, are presented

Design of reliable and energy-efficient high-speed interface circuits

The data-rate demand in high-speed interface circuits increases exponentially every year. High-speed I/Os are better implemented in advanced process technologies for lower-power systems, with the advantages of improved driving capability of the transistors and reduced parasitic capacitance. However, advanced technologies are not necessarily advantageous in terms of device reliability; in particular device failure from electrostatic discharge (ESD) becomes more likely in nano-scale process nodes. In order to secure ESD resiliency, the size of ESD devices on I/O pads should be sufficiently large, which may potentially reduce I/O speed. These two conflicting requirements in high-speed I/O design sometimes require sacrifice to one of the two properties. In this dissertation, three different approaches are proposed to achieve reliable and energy-efficient interface circuits. As the first approach, a novel ESD self-protection scheme to utilize “adaptive active bias conditioning” is proposed to reduce voltage stress on the vulnerable transistors, thereby reducing the burden on ESD protection devices. The second approach is to cancel out effective parasitic capacitance from ESD devices by the T-coil network. Voltage overshoot generated by magnetic coupling of the T-coil network can be suppressed by the proposed “inductance halving” technique, which reduces mutual inductance during ESD. The last approach employs system-level knowledge in the design of an ADC-based receiver for high intersymbol interference (ISI) channels. As a system-level performance metric, bit-error rate (BER) is adopted to mitigate a bit-resolution requirement in “BER-optimal ADC”, which can lead to 2× power-efficiency in the flash ADC and achieve a better BER performance

PHY Link Design and Optimization For High-Speed Low-Power Communication Systems

The ever-growing demands for high-bandwidth data transfer have been pushing towards advancing research efforts in the field of high-performing communication systems. Studies on the performance of single chip, e.g. faster multi-core processors and higher system memory capacity, have been explored. To further enhance the system performance, researches have been focused on the improvement of data-transfer bandwidth for chip-to-chip communication in the high-speed serial link. Many solutions have been addressed to overcome the bottleneck caused by the non-idealties such as bandwidth-limited electrical channel that connects two link devices and varieties of undesired noise in the communication systems. Nevertheless, with these solutions data have run into limitations of the timing margins for high-speed interfaces running at multiple gigabits per second data rates on low-cost Printed Circuit Board (PCB) material with constrained power budget. Therefore, the challenge in designing a physical layer (PHY) link for high-speed communication systems turns out to be power-efficient, reliable and cost-effective. In this context, this dissertation is intended to focus on architectural design, system-level and circuit-level verification of a PHY link as well as system performance optimization in respective of power, reliability and adaptability in high-speed communication systems. The PHY is mainly composed of clock data recovery (CDR), equalizers (EQs) and high- speed I/O drivers. Symmetrical structure of the PHY link is usually duplicated in both link devices for bidirectional data transmission. By introducing training mechanisms into high-speed communication systems, the timing in one link device is adaptively aligned to the timing condition specified in the other link device despite of different skews or induced jitter resulting from process, voltage and temperature (PVT) variations in the individual link. With reliable timing relationships among the interface signals provided, the total system bandwidth is dramatically improved. On the other hand, interface training offers high flexibility for reuse without further investigation on high demanding components involved in high costs. In the training mode, a CDR module is essential for reconstructing the transmitted bitstream to achieve the best data eye and to detect the edges of data stream in asynchronous systems or source-synchronous systems. Generally, the CDR works as a feedback control system that aligns its output clock to the center of the received data. In systems that contain multiple data links, the overall CDR power consumption increases linearly with the increase in number of links as one CDR is required for each link. Therefore, a power-efficient CDR plays a significant role in such systems with parallel links. Furthermore, a high performance CDR requires low jitter generation in spite of high input jitter. To minimize the trade-off between power consumption and CDR jitter, a novel CDR architecture is proposed by utilizing the proportional-integral (PI) controller and three times sampling scheme. Meanwhile, signal integrity (SI) becomes critical as the data rate exceeds several gigabits per second. Distorted data due to the non-idealties in systems are likely to reduce the signal quality aggressively and result in intolerable transmission errors in worst case scenarios, thus affect the system effective bandwidth. Hence, additional trainings such as transmitter (Tx) and receiver (Rx) EQ trainings for SI purpose are inserted into the interface training. Besides, a simplified system architecture with unsymmetrical placement of adaptive Rx and Tx EQs in a single link device is proposed and analyzed by using different coefficient adaptation algorithms. This architecture enables to reduce a large number of EQs through the training, especially in case of parallel links. Meanwhile, considerable power and chip area are saved. Finally, high-speed I/O driver against PVT variations is discussed. Critical issues such as overshoot and undershoot interfering with the data are primarily accompanied by impedance mismatch between the I/O driver and its transmitting channel. By applying PVT compensation technique I/O driver impedances can be effectively calibrated close to the target value. Different digital impedance calibration algorithms against PVT variations are implemented and compared for achieving fast calibration and low power requirements

Design of Energy-Efficient Equalization and Data Encoding/Decoding Techniques for Wireline Communication Systems

Ever increasing global internet data traffic has driven up the demand for cutting-edge high-speed wireline communication systems including SerDes PHY for various interfaces, interconnects, data centers servers and switches in optical systems. Operating wireline communications at higher data rates leads to signals suffering from greater channel loss and exponential increase in power consumption, mainly caused by a heavier amount of required equalization. In this dissertation, two distinct methodologies for designing SerDes transceivers are presented: 1) a pulse width modulated (PWM) time-domain feed forward equalizer (FFE) and linearity improvement technique for higher-order pulse amplitude modulation (PAM) including PAM-8, and 2) an inter-symbol interference (ISI)-resilient data encoding and decoding technique with Dicode encoding and error correction logic for low-bandwidth wireline channels, as an alternative strategy for communicating in an energy-efficient way on bandwidth-limited wireline channels without using conventional equalizers or filters. The first topic is a PAM-8 wireline transceiver with receiver-side pulse-width-modulated (PWM) or time-domain based feed forward equalization (FFE) technique. The receiver converts voltage-modulated signals or PAM signals to PWM signals and processes them using inverter based delay elements having rail to rail voltage swing. Time-to-voltage and voltage-to-time converters are designed to have non-linearity with opposite signs with the aim of achieving higher front-end linearity on the receiver. The proposed PAM-8 transceiver can operate from 12.0 Gb/s to 39.6 Gb/s and compensates 14 dB loss at 6.6 GHz with an efficiency of 8.66 pJ/bit in 65 nm CMOS. The second topic is an alternative strategy for communicating on bandwidth-limited wireline channels without using conventional equalizers or filters (FFE, DFE, and CTLE): Inter-symbol interference (ISI) resilient Dicode encoding and error correction for low-bandwidth wireline channels. The key observation is that Dicode-encoded data have no consecutive 1s or -1s. With this known information, the error correction logic at the receiver can correct multi-bit errors due to ISI. Implemented in 65 nm CMOS, the proposed digital encoding and decoding approach can achieve BER less than 10−12 while communicating on a channel with an insertion loss of 24.2 dB and 21.4 dB with 2.56 pJ/bit and 2.66 pJ/bit efficiency while operating at 13.6 Gb/s and 16 Gb/s, respectively