Design of robust spin-transfer torque magnetic random access memories for ultralow power high performance on-chip cache applications

Spin-transfer torque magnetic random access memories (STT-MRAMs) based on magnetic tunnel junction (MTJ) has become the leading candidate for future universal memory technology due to its potential for low power, non-volatile, high speed and extremely good endurance. However, conflicting read and write requirements exist in STT-MRAM technology because the current path during read and write operations are the same. Read and write failures of STT-MRAMs are degraded further under process variations. The focus of this dissertation is to optimize the yield of STT- MRAMs under process variations by employing device-circuit-architecture co-design techniques. A devices-to-systems simulation framework was developed to evaluate the effectiveness of the techniques proposed in this dissertation. An optimization methodology for minimizing the failure probability of 1T-1MTJ STT-MRAM bit-cell by proper selection of bit-cell configuration and access transistor sizing is also proposed. A failure mitigation technique using assistsin 1T-1MTJ STT-MRAM bit-cells is also proposed and discussed. Assist techniques proposed in this dissertation to mitigate write failures either increase the amount of current available to switch the MTJ during write or decrease the required current to switch the MTJ. These techniques achieve significant reduction in bit-cell area and write power with minimal impact on bit-cell failure probability and read power. However, the proposed write assist techniques may be less effective in scaled STT-MRAM bit-cells. Furthermore, read failures need to be overcome and hence, read assist techniques are required. It has been experimentally demonstrated that a class of materials called multiferroics can enable manipulation of magnetization using electric fields via magnetoelectric effects. A read assist technique using an MTJ structure incorporating multiferroic materials is proposed and analyzed. It was found that it is very difficult to overcome the fundamental design issues with 1T-1MTJ STT-MRAM due to the two-terminal nature of the MTJ. Hence, multi-terminal MTJ structures consisting of complementary polarized pinned layers are proposed. Analysis of the proposed MTJ structures shows significant improvement in bit-cell failures. Finally, this dissertation explores two system-level applications enabled by STT-MRAMs, and shows that device-circuit-architecture co-design of STT-MRAMs is required to fully exploit its benefits

LOW POWER CIRCUITS DESIGN USING RESISTIVE NON-VOLATILE MEMORIES

Ph.DDOCTOR OF PHILOSOPH

Gestión de jerarquías de memoria híbridas a nivel de sistema

Tesis inédita de la Universidad Complutense de Madrid, Facultad de Informática, Departamento de Arquitectura de Computadoras y Automática y de Ku Leuven, Arenberg Doctoral School, Faculty of Engineering Science, leída el 11/05/2017.In electronics and computer science, the term ‘memory’ generally refers to devices that are used to store information that we use in various appliances ranging from our PCs to all hand-held devices, smart appliances etc. Primary/main memory is used for storage systems that function at a high speed (i.e. RAM). The primary memory is often associated with addressable semiconductor memory, i.e. integrated circuits consisting of silicon-based transistors, used for example as primary memory but also other purposes in computers and other digital electronic devices. The secondary/auxiliary memory, in comparison provides program and data storage that is slower to access but offers larger capacity. Examples include external hard drives, portable flash drives, CDs, and DVDs. These devices and media must be either plugged in or inserted into a computer in order to be accessed by the system. Since secondary storage technology is not always connected to the computer, it is commonly used for backing up data. The term storage is often used to describe secondary memory. Secondary memory stores a large amount of data at lesser cost per byte than primary memory; this makes secondary storage about two orders of magnitude less expensive than primary storage. There are two main types of semiconductor memory: volatile and nonvolatile. Examples of non-volatile memory are ‘Flash’ memory (sometimes used as secondary, sometimes primary computer memory) and ROM/PROM/EPROM/EEPROM memory (used for firmware such as boot programs). Examples of volatile memory are primary memory (typically dynamic RAM, DRAM), and fast CPU cache memory (typically static RAM, SRAM, which is fast but energy-consuming and offer lower memory capacity per are a unit than DRAM). Non-volatile memory technologies in Si-based electronics date back to the 1990s. Flash memory is widely used in consumer electronic products such as cellphones and music players and NAND Flash-based solid-state disks (SSDs) are increasingly displacing hard disk drives as the primary storage device in laptops, desktops, and even data centers. The integration limit of Flash memories is approaching, and many new types of memory to replace conventional Flash memories have been proposed. The rapid increase of leakage currents in Silicon CMOS transistors with scaling poses a big challenge for the integration of SRAM memories. There is also the case of susceptibility to read/write failure with low power schemes. As a result of this, over the past decade, there has been an extensive pooling of time, resources and effort towards developing emerging memory technologies like Resistive RAM (ReRAM/RRAM), STT-MRAM, Domain Wall Memory and Phase Change Memory(PRAM). Emerging non-volatile memory technologies promise new memories to store more data at less cost than the expensive-to build silicon chips used by popular consumer gadgets including digital cameras, cell phones and portable music players. These new memory technologies combine the speed of static random-access memory (SRAM), the density of dynamic random-access memory (DRAM), and the non-volatility of Flash memory and so become very attractive as another possibility for future memory hierarchies. The research and information on these Non-Volatile Memory (NVM) technologies has matured over the last decade. These NVMs are now being explored thoroughly nowadays as viable replacements for conventional SRAM based memories even for the higher levels of the memory hierarchy. Many other new classes of emerging memory technologies such as transparent and plastic, three-dimensional(3-D), and quantum dot memory technologies have also gained tremendous popularity in recent years...En el campo de la informática, el término ‘memoria’ se refiere generalmente a dispositivos que son usados para almacenar información que posteriormente será usada en diversos dispositivos, desde computadoras personales (PC), móviles, dispositivos inteligentes, etc. La memoria principal del sistema se utiliza para almacenar los datos e instrucciones de los procesos que se encuentre en ejecución, por lo que se requiere que funcionen a alta velocidad (por ejemplo, DRAM). La memoria principal está implementada habitualmente mediante memorias semiconductoras direccionables, siendo DRAM y SRAM los principales exponentes. Por otro lado, la memoria auxiliar o secundaria proporciona almacenaje(para ficheros, por ejemplo); es más lenta pero ofrece una mayor capacidad. Ejemplos típicos de memoria secundaria son discos duros, memorias flash portables, CDs y DVDs. Debido a que estos dispositivos no necesitan estar conectados a la computadora de forma permanente, son muy utilizados para almacenar copias de seguridad. La memoria secundaria almacena una gran cantidad de datos aun coste menor por bit que la memoria principal, siendo habitualmente dos órdenes de magnitud más barata que la memoria primaria. Existen dos tipos de memorias de tipo semiconductor: volátiles y no volátiles. Ejemplos de memorias no volátiles son las memorias Flash (algunas veces usadas como memoria secundaria y otras veces como memoria principal) y memorias ROM/PROM/EPROM/EEPROM (usadas para firmware como programas de arranque). Ejemplos de memoria volátil son las memorias DRAM (RAM dinámica), actualmente la opción predominante a la hora de implementar la memoria principal, y las memorias SRAM (RAM estática) más rápida y costosa, utilizada para los diferentes niveles de cache. Las tecnologías de memorias no volátiles basadas en electrónica de silicio se remontan a la década de1990. Una variante de memoria de almacenaje por carga denominada como memoria Flash es mundialmente usada en productos electrónicos de consumo como telefonía móvil y reproductores de música mientras NAND Flash solid state disks(SSDs) están progresivamente desplazando a los dispositivos de disco duro como principal unidad de almacenamiento en computadoras portátiles, de escritorio e incluso en centros de datos. En la actualidad, hay varios factores que amenazan la actual predominancia de memorias semiconductoras basadas en cargas (capacitivas). Por un lado, se está alcanzando el límite de integración de las memorias Flash, lo que compromete su escalado en el medio plazo. Por otra parte, el fuerte incremento de las corrientes de fuga de los transistores de silicio CMOS actuales, supone un enorme desafío para la integración de memorias SRAM. Asimismo, estas memorias son cada vez más susceptibles a fallos de lectura/escritura en diseños de bajo consumo. Como resultado de estos problemas, que se agravan con cada nueva generación tecnológica, en los últimos años se han intensificado los esfuerzos para desarrollar nuevas tecnologías que reemplacen o al menos complementen a las actuales. Los transistores de efecto campo eléctrico ferroso (FeFET en sus siglas en inglés) se consideran una de las alternativas más prometedores para sustituir tanto a Flash (por su mayor densidad) como a DRAM (por su mayor velocidad), pero aún está en una fase muy inicial de su desarrollo. Hay otras tecnologías algo más maduras, en el ámbito de las memorias RAM resistivas, entre las que cabe destacar ReRAM (o RRAM), STT-RAM, Domain Wall Memory y Phase Change Memory (PRAM)...Depto. de Arquitectura de Computadores y AutomáticaFac. de InformáticaTRUEunpu

Evaluation of STT-MRAM main memory for HPC and real-time systems

It is questionable whether DRAM will continue to scale and will meet the needs of next-generation systems. Therefore, significant effort is invested in research and development of novel memory technologies. One of the candidates for nextgeneration memory is Spin-Transfer Torque Magnetic Random Access Memory (STT-MRAM). STT-MRAM is an emerging non-volatile memory with a lot of potential that could be exploited for various requirements of different computing systems. Being a novel technology, STT-MRAM devices are already approaching DRAM in terms of capacity, frequency and device size. Special STT-MRAM features such as intrinsic radiation hardness, non-volatility, zero stand-by power and capability to function in extreme temperatures also make it particularly suitable for aerospace, avionics and automotive applications. Despite of being a conceivable alternative for main memory technology, to this day, academic research of STT-MRAM main memory remains marginal. This is mainly due to the unavailability of publicly available detailed timing parameters of this novel technology, which are required to perform a cycle accurate main memory simulation. Some researchers adopt simplistic memory models to simulate main memory, but such models can introduce significant errors in the analysis of the overall system performance. Therefore, detailed timing parameters are a must-have for any evaluation or architecture exploration study of STT-MRAM main memory. These detailed parameters are not publicly available because STT-MRAM manufacturers are reluctant to release any delicate information on the technology. This thesis demonstrates an approach to perform a cycle accurate simulation of STT-MRAM main memory, being the first to release detailed timing parameters of this technology from academia, essentially enabling researchers to conduct reliable system level simulation of STT-MRAM using widely accepted existing simulation infrastructure. Our results show that, in HPC domain STT-MRAM provide performance comparable to DRAM. Results from the power estimation indicates that STT-MRAM power consumption increases significantly for Activation/Precharge power while Burst power increases moderately and Background power does not deviate much from DRAM. The thesis includes detailed STT-MRAM main memory timing parameters to the main repositories of DramSim2 and Ramulator, two of the most widely used and accepted state-of-the-art main memory simulators. The STT-MRAM timing parameters that has been originated as a part of this thesis, are till date the only reliable and publicly available timing information on this memory technology published from academia. Finally, the thesis analyzes the feasibility of using STT-MRAM in real-time embedded systems by investigating STT-MRAM main memory impact on average system performance and WCET. STT-MRAM's suitability for the real-time embedded systems is validated on benchmarks provided by the European Space Agency (ESA), EEMBC Autobench and MediaBench suite by analyzing performance and WCET impact. In quantitative terms, our results show that STT-MRAM main memory in real-time embedded systems provides performance and WCET comparable to conventional DRAM, while opening up opportunities to exploit various advantages.Es cuestionable si DRAM continuará escalando y cumplirá con las necesidades de los sistemas de la próxima generación. Por lo tanto, se invierte un esfuerzo significativo en la investigación y el desarrollo de nuevas tecnologías de memoria. Uno de los candidatos para la memoria de próxima generación es la Spin-Transfer Torque Magnetic Random Access Memory (STT-MRAM). STT-MRAM es una memoria no volátil emergente con un gran potencial que podría ser explotada para diversos requisitos de diferentes sistemas informáticos. Al ser una tecnología novedosa, los dispositivos STT-MRAM ya se están acercando a la DRAM en términos de capacidad, frecuencia y tamaño del dispositivo. Las características especiales de STTMRAM, como la dureza intrínseca a la radiación, la no volatilidad, la potencia de reserva cero y la capacidad de funcionar en temperaturas extremas, también lo hacen especialmente adecuado para aplicaciones aeroespaciales, de aviónica y automotriz. A pesar de ser una alternativa concebible para la tecnología de memoria principal, hasta la fecha, la investigación académica de la memoria principal de STT-MRAM sigue siendo marginal. Esto se debe principalmente a la falta de disponibilidad de los parámetros de tiempo detallados públicamente disponibles de esta nueva tecnología, que se requieren para realizar un ciclo de simulación de memoria principal precisa. Algunos investigadores adoptan modelos de memoria simplistas para simular la memoria principal, pero tales modelos pueden introducir errores significativos en el análisis del rendimiento general del sistema. Por lo tanto, los parámetros de tiempo detallados son indispensables para cualquier evaluación o estudio de exploración de la arquitectura de la memoria principal de STT-MRAM. Estos parámetros detallados no están disponibles públicamente porque los fabricantes de STT-MRAM son reacios a divulgar información delicada sobre la tecnología. Esta tesis demuestra un enfoque para realizar un ciclo de simulación precisa de la memoria principal de STT-MRAM, siendo el primero en lanzar parámetros de tiempo detallados de esta tecnología desde la academia, lo que esencialmente permite a los investigadores realizar una simulación confiable a nivel de sistema de STT-MRAM utilizando una simulación existente ampliamente aceptada infraestructura. Nuestros resultados muestran que, en el dominio HPC, STT-MRAM proporciona un rendimiento comparable al de la DRAM. Los resultados de la estimación de potencia indican que el consumo de potencia de STT-MRAM aumenta significativamente para la activation/Precharge power, mientras que la Burst power aumenta moderadamente y la Background power no se desvía mucho de la DRAM. La tesis incluye parámetros detallados de temporización memoria principal de STT-MRAM a los repositorios principales de DramSim2 y Ramulator, dos de los simuladores de memoria principal más avanzados y más utilizados y aceptados. Los parámetros de tiempo de STT-MRAM que se han originado como parte de esta tesis, son hasta la fecha la única información de tiempo confiable y disponible al público sobre esta tecnología de memoria publicada desde la academia. Finalmente, la tesis analiza la viabilidad de usar STT-MRAM en real-time embedded systems mediante la investigación del impacto de la memoria principal de STT-MRAM en el rendimiento promedio del sistema y WCET. La idoneidad de STTMRAM para los real-time embedded systems se valida en los applicaciones proporcionados por la European Space Agency (ESA), EEMBC Autobench y MediaBench, al analizar el rendimiento y el impacto de WCET. En términos cuantitativos, nuestros resultados muestran que la memoria principal de STT-MRAM en real-time embedded systems proporciona un desempeño WCET comparable al de una memoria DRAM convencional, al tiempo que abre oportunidades para explotar varias ventajas

Energy efficient hybrid computing systems using spin devices

Emerging spin-devices like magnetic tunnel junctions (MTJ\u27s), spin-valves and domain wall magnets (DWM) have opened new avenues for spin-based logic design. This work explored potential computing applications which can exploit such devices for higher energy-efficiency and performance. The proposed applications involve hybrid design schemes, where charge-based devices supplement the spin-devices, to gain large benefits at the system level. As an example, lateral spin valves (LSV) involve switching of nanomagnets using spin-polarized current injection through a metallic channel such as Cu. Such spin-torque based devices possess several interesting properties that can be exploited for ultra-low power computation. Analog characteristic of spin current facilitate non-Boolean computation like majority evaluation that can be used to model a neuron. The magneto-metallic neurons can operate at ultra-low terminal voltage of ∼20mV, thereby resulting in small computation power. Moreover, since nano-magnets inherently act as memory elements, these devices can facilitate integration of logic and memory in interesting ways. The spin based neurons can be integrated with CMOS and other emerging devices leading to different classes of neuromorphic/non-Von-Neumann architectures. The spin-based designs involve `mixed-mode\u27 processing and hence can provide very compact and ultra-low energy solutions for complex computation blocks, both digital as well as analog. Such low-power, hybrid designs can be suitable for various data processing applications like cognitive computing, associative memory, and currentmode on-chip global interconnects. Simulation results for these applications based on device-circuit co-simulation framework predict more than ∼100x improvement in computation energy as compared to state of the art CMOS design, for optimal spin-device parameters

Nonvolatile voltage controlled molecular spin‐state switching for memory applications

Nonvolatile, molecular multiferroic devices have now been demonstrated, but it is worth giving some consideration to the issue of whether such devices could be a competitive alternative for solid-state nonvolatile memory. For the Fe (II) spin crossover complex [Fe{H2B(pz)2}2(bipy)], where pz = tris(pyrazol-1-yl)-borohydride and bipy = 2,20-bipyridine, voltage-controlled isothermal changes in the electronic structure and spin state have been demonstrated and are accompanied by changes in conductance. Higher conductance is seen with [Fe{H2B(pz)2}2(bipy)] in the high spin state, while lower conductance occurs for the low spin state. Plausibly, there is the potential here for low-cost molecular solid-state memory because the essential molecular thin films are easily fabricated. However, successful device fabrication does not mean a device that has a practical value. Here, we discuss the progress and challenges yet facing the fabrication of molecular multiferroic devices, which could be considered competitive to silicon

X-SRAM: Enabling In-Memory Boolean Computations in CMOS Static Random Access Memories

Silicon-based Static Random Access Memories (SRAM) and digital Boolean logic have been the workhorse of the state-of-art computing platforms. Despite tremendous strides in scaling the ubiquitous metal-oxide-semiconductor transistor, the underlying \textit{von-Neumann} computing architecture has remained unchanged. The limited throughput and energy-efficiency of the state-of-art computing systems, to a large extent, results from the well-known \textit{von-Neumann bottleneck}. The energy and throughput inefficiency of the von-Neumann machines have been accentuated in recent times due to the present emphasis on data-intensive applications like artificial intelligence, machine learning \textit{etc}. A possible approach towards mitigating the overhead associated with the von-Neumann bottleneck is to enable \textit{in-memory} Boolean computations. In this manuscript, we present an augmented version of the conventional SRAM bit-cells, called \textit{the X-SRAM}, with the ability to perform in-memory, vector Boolean computations, in addition to the usual memory storage operations. We propose at least six different schemes for enabling in-memory vector computations including NAND, NOR, IMP (implication), XOR logic gates with respect to different bit-cell topologies $-$ the 8T cell and the 8$^+$T Differential cell. In addition, we also present a novel \textit{`read-compute-store'} scheme, wherein the computed Boolean function can be directly stored in the memory without the need of latching the data and carrying out a subsequent write operation. The feasibility of the proposed schemes has been verified using predictive transistor models and Monte-Carlo variation analysis.Comment: This article has been accepted in a future issue of IEEE Transactions on Circuits and Systems-I: Regular Paper