Heterogeneous Integration on Silicon-Interconnect Fabric using fine-pitch interconnects (≤10 �m)

Today, the ever-growing data-bandwidth demand is pushing the boundaries of the traditional printed circuit board (PCB) based integration schemes. Moreover, with the apparent saturation of semiconductor scaling, commonly called Moore's law, system scaling warrants a paradigm shift in packaging technologies, assembly techniques, and integration methodologies. In this work, a superior alternative to PCBs called the Silicon-Interconnect Fabric (Si-IF) is investigated. The Si-IF is a silicon-based, package-less, fine-pitch, highly scalable, heterogeneous integration platform for wafer-scale systems. In this technology, unpackaged dielets are assembled on the Si-IF at small inter-dielet spacings (≤100 �m) using fine-pitch (≤10 �m) die-to-substrate interconnects. A novel assembly process using a solder-less direct metal-metal (gold-gold and copper-copper) thermal compression bonding was developed. Using this process, sub-10 �m pitch interconnects with a low specific contact resistance of ≤0.7 Ω-�m2 were successfully demonstrated. Because of the tightly packed Si-IF assembly, the communication links between the neighboring dies are short (≤500 �m) with low loss (≤2 dB), comparable to on-chip connections. Consequently, simple buffers can transfer data between dies using a Simple Universal Parallel intERface for chips (SuperCHIPS) at low latency (<30 ps), low energy per bit (≤0.03 pJ/b), and high data-rates (up to 10 Gbps/link), corresponding to an aggregate bandwidth up to 8 Tbps/mm. The benefits of the SuperCHIPS protocol were experimentally demonstrated to provide 5-90X higher data-bandwidth, 8-30X lower latency, and 5-40X lower energy per bit compared to existing integration schemes. This dissertation addresses the assembly technology and communication protocols of the Si-IF technology

Microstructural and mechanical characteristics of micro-scale intermetallic compounds interconnections

Following the continually increasing demand for high-density interconnection and multilayer packaging for chips, solder bump size has decreased significantly over the years, this has led to some challenges in the reliability of interconnects. This thesis presents research into the resulting effects of miniaturization on the interconnection with Sn-solder, especially focusing on the full intermetallics (IMCs) micro-joints which appear in the 3D IC stacking packaging. Thereby, systematic studies have been conducted to study the microstructural evolution and reliability issues of Cu-Sn and Cu-Sn-Ni IMCs micro-joints. (1) Phenomenon of IMCs planar growth: The planar IMCs interlayer was asymmetric and composed of (Cu,Ni)6Sn5 mainly in Ni/Sn (2.5~5 µm)/Cu interconnect. Meanwhile, it was symmetric two-layer structure in Cu/Sn (2.5~5 µm)/Cu interconnect with the Cu3Sn fine grains underneath Cu6Sn5 cobblestone-shape-like grains for each IMCs layer. Besides, it is worth noticing that the appearance of Cu-rich whiskers (the mixture of Cu/Cu2O/SnOx/Cu6Sn5) could potentially lead to short-circuit in the cases of ultra-fine (<10 µm pitch) interconnects for the miniaturization of electronics devices. (2) Microstructural evolution process of Cu-Sn IMCs micro-joint: The simultaneous solidification of IMCs interlayer supressed the scalloped growth of Cu6Sn5 grains in Cu/Sn (2.5 µm)/Cu interconnect during the transient liquid phase (TLP) soldering process. The growth factor of Cu3Sn was in the range of 0.29~0.48 in Cu-Cu6Sn5 diffusion couple at 240~290 °C, which was impacted significantly by the type of substrates. And the subsequent homogenization process of Cu3Sn grains was found to be consistent with the description of flux-driven ripening (FDR) theory. Moreover, Kirkendall voids appeared only in the Cu3Sn layer adjacent to Cu-plated substrate, and this porous Cu3Sn micro-joint was mechanically robust during the shear test. (3) Microstructural evolution of Cu-Sn-Ni IMCs micro-joint: There was obvious inter-reaction between the interfacial reactions in Ni/Sn (1.5 µm)/Cu interconnect. The growth factor of (Cu,Ni)3Sn on Cu side was about 0.36 at 240 °C, and the reaction product on Ni side was changed from Ni3Sn4 into (Cu,Ni)6Sn5 with the increase of soldering temperature. In particular, the segregation of Ni atoms occurred along with phase transformation at 290 °C and thereby stabilized the (Cu,Ni)6Sn5 phase for the high Ni content of 20 at.%. (4) Micro-mechanical characteristics of Cu-Sn-Ni IMCs micro-joint: The Young s modulus and hardness of Cu-Sn-Ni IMCs were measured by nanoindentation test, such as 160.6±3.1 GPa/ 7.34±0.14 GPa for (Cu,Ni)6Sn5 and 183.7±4.0 GPa/ 7.38±0.46 GPa for (Cu,Ni)3Sn, respectively. Besides, in-situ nano-compression tests have been conducted on IMCs micro-cantilevers, the fracture strength turns out to be 2.46 GPa. And also, the ultimate tensile stress was calculated to be 2.3±0.7 GPa from in-situ micro-bending tests, which is not sensitive with the microstructural change of IMCs after dwelling at 290 °C

Bed of nails(B0N) - 100 microns pitch wafer level off-chip interconnects for microelectronic packaging applications

Master'sMASTER OF ENGINEERIN

Book of Knowledge (BOK) for NASA Electronic Packaging Roadmap

The objective of this document is to update the NASA roadmap on packaging technologies (initially released in 2007) and to present the current trends toward further reducing size and increasing functionality. Due to the breadth of work being performed in the area of microelectronics packaging, this report presents only a number of key packaging technologies detailed in three industry roadmaps for conventional microelectronics and a more recently introduced roadmap for organic and printed electronics applications. The topics for each category were down-selected by reviewing the 2012 reports of the International Technology Roadmap for Semiconductor (ITRS), the 2013 roadmap reports of the International Electronics Manufacturing Initiative (iNEMI), the 2013 roadmap of association connecting electronics industry (IPC), the Organic Printed Electronics Association (OE-A). The report also summarizes the results of numerous articles and websites specifically discussing the trends in microelectronics packaging technologies

異種ダイレット積層を用いたフレキシブルハイブリッドデバイスの集積技術に関する研究

Tohoku University福島誉史課

Compliant copper microwire arrays for reliable interconnections between large low-CTE packages and printed wiring board

The trend to high I/O density, performance and miniaturization at low cost is driving the industry towards shrinking interposer design rules, requiring a new set of packaging technologies. Low-CTE packages from silicon, glass and low-CTE organic substrates enable high interconnection density, high reliability and integration of system components. However, the large CTE mismatch between the package and the board presents reliability challenges for the board-level interconnections. Novel stress-relief structures that can meet reliability requirements along with electrical performance while meeting the cost constraints are needed to address these challenges. This thesis focuses on a comprehensive methodology starting with modeling, design, fabrication and characterization to validate such stress-relief structures. This study specifically explores SMT-compatible stress-relief microwire arrays in thin polymer carriers as a unique and low-cost solution for reliable board-level interconnections between large low-CTE packages and printed wiring boards. The microwire arrays are pre-fabricated in ultra-thin carriers using low-cost manufacturing processes such as laser vias and copper electroplating, which are then assembled in between the interposer and printed wiring board (PWB) as stress-relief interlayers. The microwire array results in dramatic reduction in solder stresses and strains, even with larger interposer sizes (20 mm × 20 mm), at finer pitch (400 microns), without the need for underfill. The parallel wire arrays result in low resistance and inductance, and therefore do not degrade the electrical performance. The scalability of the structures and the unique processes, from micro to nanowires, provides extendibility to finer pitch and larger package sizes. Finite element method (FEM) was used to study the reliability of the interconnections to provide guidelines for the test vehicle design. The models were built in 2.5D geometries to study the reliability of 400 µm-pitch interconnections with a 100 µm thick, 20 mm × 20 mm silicon package that was SMT-assembled onto an organic printed wiring board. The performance of the microwire array interconnection is compared to that of ball grid array (BGA) interconnections, in warpage, equivalent plastic strain and projected fatigue life. A unique set of materials and processes was used to demonstrate the low-cost fabrication of microwire arrays. Copper microwires with 12 µm diameter and 50 µm height were fabricated on both sides of a 50 µm thick, thermoplastic polymer carrier using dryfilm based photolithography and bottom-up electrolytic plating. The copper microwire interconnections were assembled between silicon interposer and FR-4 PWB through SMT-compatible process. Thermal mechanical reliability of the interconnections was characterized by thermal cycling test from -40°C to 125°C. The initial fatigue failure in the interconnections was identified at 700 cycles in the solder on the silicon package side, which is consistent with the modeling results. This study therefore demonstrated a highly-reliable and SMT-compatible solution for board-level interconnections between large low-CTE packages and printed wiring board.Ph.D

Optoelectronic devices and packaging for information photonics

This thesis studies optoelectronic devices and the integration of these components onto optoelectronic multi chip modules (OE-MCMs) using a combination of packaging techniques. For this project, (1×12) array photodetectors were developed using PIN diodes with a GaAs/AlGaAs strained layer structure. The devices had a pitch of 250μm, operated at a wavelength of 850nm. Optical characterisation experiments of two types of detector arrays (shoe and ring) were successfully performed. Overall, the shoe devices achieved more consistent results in comparison with ring diodes, i.e. lower dark current and series resistance values. A decision was made to choose the shoe design for implementation into the high speed systems demonstrator. The (1x12) VCSEL array devices were the optical sources used in my research. This was an identical array at 250μm pitch configuration used in order to match the photodetector array. These devices had a wavelength of 850nm. Optoelectronic testing of the VCSEL was successfully conducted, which provided good beam profile analysis and I-V-P measurements of the VCSEL array. This was then implemented into a simple demonstrator system, where eye diagrams examined the systems performance and characteristics of the full system and showed positive results. An explanation was given of the following optoelectronic bonding techniques: Wire bonding and flip chip bonding with its associated technologies, i.e. Solder, gold stud bump and ACF. Also, technologies, such as ultrasonic flip chip bonding and gold micro-post technology were looked into and discussed. Experimental work implementing these methods on packaging the optoelectronic devices was successfully conducted and described in detail. Packaging of the optoelectronic devices onto the OEMCM was successfully performed. Electrical tests were successfully carried out on the flip chip bonded VCSEL and Photodetector arrays. These results verified that the devices attached on the MCM achieved good electrical performance and reliable bonding. Finally, preliminary testing was conducted on the fully assembled OE-MCMs. The aim was to initially power up the mixed signal chip (VCSEL driver), and then observe the VCSEL output

MICROELECTRONICS PACKAGING TECHNOLOGY ROADMAPS, ASSEMBLY RELIABILITY, AND PROGNOSTICS

This paper reviews the industry roadmaps on commercial-off-the shelf (COTS) microelectronics packaging technologies covering the current trends toward further reducing size and increasing functionality. Due tothe breadth of work being performed in this field, this paper presents only a number of key packaging technologies. The topics for each category were down-selected by reviewing reports of industry roadmaps including the International Technology Roadmap for Semiconductor (ITRS) and by surveying publications of the International Electronics Manufacturing Initiative (iNEMI) and the roadmap of association connecting electronics industry (IPC). The paper also summarizes the findings of numerous articles and websites that allotted to the emerging and trends in microelectronics packaging technologies. A brief discussion was presented on packaging hierarchy from die to package and to system levels. Key elements of reliability for packaging assemblies were presented followed by reliabilty definition from a probablistic failure perspective. An example was present for showing conventional reliability approach using Monte Carlo simulation results for a number of plastic ball grid array (PBGA). The simulation results were compared to experimental thermal cycle test data. Prognostic health monitoring (PHM) methods, a growing field for microelectronics packaging technologies, were briefly discussed. The artificial neural network (ANN), a data-driven PHM, was discussed in details. Finally, it presented inter- and extra-polations using ANN simulation for thermal cycle test data of PBGA and ceramic BGA (CBGA) assemblies

All-copper chip-to-substrate interconnects for high performance integrated circuit devices

In this work, all-copper connections between silicon microchips and substrates are developed. The semiconductor industry advances the transistor density on a microchip based on the roadmap set by Moore's Law. Communicating with a microprocessor which has nearly one billion transistors is a daunting challenge. Interconnects from the chip to the system (i.e. memory, graphics, drives, power supply) are rapidly growing in number and becoming a serious concern. Specifically, the solder ball connections that are formed between the chip itself and the package are challenging to make and still have acceptable electrical and mechanical performance. These connections are being required to increase in number, increase in power current density, and increase in off-chip operating frequency. Many of the challenges with using solder connections are limiting these areas. In order to advance beyond the limitations of solder for electrical and mechanical performance, a novel approach to creating all-copper connections from the chip-to-substrate has been developed. The development included characterizing the electroless plating and annealing process used to create the connections, designing these connections to be compatible with the stress requirements for fragile low-k devices, and finally by improving the plating/annealing process to become process time competitive with solder. It was found that using a commercially available electroless copper bath for the plating, followed by annealing at 180 C for 1 hour, the shear strength of the copper-copper bond was approximately 165 MPa. This work resulted in many significant conclusions about the mechanism for bonding in the all-copper process and the significance of materials and geometry on the mechanical design for these connections.Ph.D.Committee Chair: Kohl, Paul; Committee Member: Bidstrup Allen, Sue Ann; Committee Member: Fuller, Thomas; Committee Member: Hesketh, Peter; Committee Member: Hess, Dennis; Committee Member: Meindl, Jame