High Velocity Oxy-Fuel (HVOF) Suspension Spraying of Mullite Coatings

This article is an invited paper selected from presentations at the 2008 International Thermal Spray Conference and has been expanded from the original presentationPeer reviewed: YesNRC publication: Ye

Metallic fume emission and operator exposure during WC-10%Co-4%Cr spraying by HVOF

Peer reviewed: NoNRC publication: Ye

Suspension plasma spraying of nanostructured WC-12Co coatings

Nanostructured WC-12% Co coatings were deposited by suspension plasma spraying of submicron feedstock powders, using an internal injection plasma torch. The liquid carrier used in this approach allows for controlled injection of much finer particles than in conventional thermal spraying, leading to thin coatings with a fine surface finish.Apolyethylene-imine (PEI) dispersant was used to stabilize the colloidal suspension in an ethanol carrier. In-flight particle states were measured for a number of operating conditions of varying plasma gas flow rates, feed rates, and standoff distances and were related to the resulting microstructure, phase composition (EDS, SEM, XRD), and Vickers hardness. High in-flight particle velocities (>800 m/s) were generated, leading to dense coatings. It was observed that the coating quality was generally compromised by the high temperature and reactivity of the small particles. To compensate for this shortcoming, the suspension feed rate was adjusted, thereby varying the thermal load on the plasma. Results showed that a slightly larger agglomerate size, in conjunction with low particle jet temperatures, could somewhat limit the decomposition of WC into brittle W\u2082C/W\u2083C and amorphous cobalt containing binder phases.Peer reviewed: YesNRC publication: Ye

SUSPENSION PLASMA SPRAYING OF INTERMEDIATE TEMPERATURE SOFC COMPONENTS USING AN AXIAL INJECTION DC TORCH

Intermediate temperature SOFC components, such as dense, nanostructured SDC electrolytes (samarium doped ceria) and porous anode sublayers were fabricated by suspension plasma spraying using an axial feed dc plasma torch. The liquid carrier employed in this approach allowed for controlled injection of much finer particles than in conventional thermal spraying, leading to thin coatings with a refined microstructure. Dense, thin (<10(m) and non-fractured electrolytes were created. Various processing routes for SOFC half-cells, using tape-cased, plasmasprayed and suspension-sprayed anodes, were explored. Loss of integrity and non-continuous coverage of the anode constituted the principal difficulties in the subsequent electrolyte deposition. The role of suspension feedstock particle size is discussed. Amongst various schemes investigated, a processing route that employs sequential suspension plasma spraying steps for both the electrolyte and the anode, using relatively large primary particles in the feedstock, constituted the most promising approach.Peer reviewed: NoNRC publication: Ye

Suspension HVOF Spraying of Reduced Temperature Solid Oxide Fuel Cell Electrolytes

Peer reviewed: YesNRC publication: Ye

Microstructure and phase stability of suspension high velocity oxy-fuel sprayed yttria stabilised zirconia coatings from aqueous and ethanol based suspensions

Two commercial 7-8 wt.% Yttria Stabilised Zirconia (YSZ) suspensions were sprayed by Suspension High Velocity Oxy Fuel (SHVOF) thermal spraying for advanced high temperature coatings. Heat treatments of the free-standing coatings were conducted at 800 °C and 1000 °C for 72 h. The SHVOF coatings using two liquid carriers: water and ethanol, behaved differently in terms of micro-structure and phase stability. The ethanol coatings retained a fully tetragonal composition after heat treatments; while the aqueous coatings, however, underwent the undesirable tetragonal to monoclinic phase transformation at 1000 °C, which is lower than previously reported temperatures (>1200 °C) in thermal sprayed YSZ coatings. The heat treatments not only resulted in densification of both coatings, but also caused excessive crystallite growth in aqueous coatings promoting the undesirable phase transformation. On the contrary, the ethanol suspension improved the phase stability by favouring the homogenization of yttrium during spraying

Structure property relationship of suspension thermally sprayed WC-Co nanocomposite coatings.

Tribomechanical properties of nanostructured coatings deposited by suspension high velocity oxy-fuel (S-HVOF) and conventional HVOF (Jet Kote) spraying were evaluated. Nanostructured S-HVOF coatings were obtained via ball milling of the agglomerated and sintered WC-12Co feedstock powder, which were deposited via an aqueous-based suspension using modified HVOF (TopGun) process. Microstructural evaluations of these hardmetal coatings included transmission electron microscopy, x-ray diffraction, and scanning electron microscopy equipped with energy dispersive x-ray spectroscopy. The nanohardness and modulus of the coated specimens were investigated using a diamond Berkovich nanoindenter. Sliding wear tests were conducted using a ball-on-flat test rig. Results indicated that low porosity coatings with nanostructured features were obtained. High carbon loss was observed, but coatings showed a high hardness up to 1000 HV2.9N. S-HVOF coatings also showed improved sliding wear and friction behavior, which were attributed to nanosized particles reducing ball wear in three-body abrasion and support of metal matrix due to uniform distribution of nanoparticles in the coating microstructure