10 research outputs found

    Propan-2-ol C3H8O + C3H8 Propane

    No full text

    Propan-2-ol C3H8O + C3H8 Propane

    No full text

    Propan-2-ol C3H8O + C3H6 Propene

    No full text

    Thermodynamic Analysis Of Autothermal Reforming Of Methane Via Entropy Maximization: Hydrogen Production

    No full text
    In this work a thermodynamic analysis of the autothermal reforming (ATR) of methane was performed. Equilibrium calculations employing entropy maximization were performed in a wide range of oxygen to methane mole ratio (O/M), steam to methane ratio (S/M), inlet temperature (IT), and system pressure (P). The main calculated parameters were hydrogen yield, carbon monoxide formation, methane conversion, coke formation, and equilibrium temperature. Further, the optimum operating oxygen to methane feed ratio that maximizes hydrogen production, at P = 1 bar, has been calculated. The nonlinear programming problem applied to the simultaneous chemical and phase equilibrium calculation was implemented in GAMS®, using CONOPT2 solver. The maximum amount of hydrogen obtained was in the order of 3 moles of hydrogen per mole of fed methane at IT = 1000 °C, P = 1 bar, S/M = 5, and O/M = 0.18. Experimental literature data are in good agreement with calculation results obtained through proposed methodology. © 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.391682578270(2012) BP Statistical Review of World Energy June 2012, , LondonEnergy Agency, I., (2012) World Energy Outlook 2012, , LondonPetrachi, G.A., Negro, G., Specchia, S., Saracco, G., Maffettone, P.L., Specchia, V., Combining catalytic combustion and steam reforming in an innovative multifunctional reactor for on-board hydrogen production from middle distillates (2005) Ind Eng Chem Res, 44 (25), pp. 9422-9430Specchia, S., Cutillo, A., Saracco, G., Specchia, V., Concept study on ATR and SR fuel processors for liquid hydrocarbons (2006) Ind Eng Chem Res, 45 (15), pp. 5298-5307Specchia, S., Negro, G., Saracco, G., Specchia, V., Fuel processor based on syngas production via short-contact-time catalytic-partial-oxidation reactors (2007) Appl Catal B Environ, 70 (14), pp. 525-531Laosiripojana, N., Assabumrungrat, S., Methane steam reforming over Ni/Ce-ZrO2 catalyst: Influences of Ce-ZrO2 support on reactivity, resistance toward carbon formation, and intrinsic reaction kinetics (2005) Appl Catal A Gen, 290 (12), pp. 200-211Hou, K., Hughes, R., The kinetics of methane steam reforming over a Ni/α-Al2O catalyst (2001) Chem Eng J, 82 (13), pp. 311-328Basini, L., Issues in H2 and synthesis gas technologies for refinery, GTL and small and distributed industrial needs (2005) Catal Today, 106 (14), pp. 34-40Souza, M.M.V.M., Schmal, M., Autothermal reforming of methane over Pt/ZrO2/Al 2O3 catalysts (2005) Appl Catal A en, 281 (12), pp. 19-24Gao, J., Guo, J., Liang, D., Hou, Z., Fei, J., Zheng, X., Production of syngas via autothermal reforming of methane in a fluidized-bed reactor over the combined CeO2-ZrO2/SiO 2 supported Ni catalysts (2008) Int J Hydrogen Energy, 33 (20), pp. 5493-5500Halabi, M.H., Croon, M.H.J.M., Van Der Schaaf, J., Modeling and analysis of autothermal reforming of methane to hydrogen in a fixed bed reformer (2008) Chem Eng J, 137 (3), pp. 568-578Chang, H.F., Pai, W.J., Chen, Y.J., Lin, W.H., Autothermal reforming of methane for producing high-purity hydrogen in a Pd/Ag membrane reactor (2010) Int J Hydrogen Energy, 35 (23), pp. 12986-12992Akbari, M.H., Ardakani, A.H.S., Tadbir, M.A., A microreactor modeling, analysis and optimization for methane autothermal reforming in fuel cell applications (2011) Chem Eng J, 166 (3), pp. 1116-1125Pino, L., Recupero, V., Beninati, S., Shukla, A.K., Hegde, M.S., Bera, P., Catalytic partial-oxidation of methane on a ceria-supported platinum catalyst for applications in fuel cell electric vehicles (2002) Appl Catal A Gen, 225 (12), pp. 63-75Pino, L., Vita, A., Cordaro, M., Recupero, V., Hegde, M.S., A comparative study of Pt/CeO2 catalyst for catalytic partial oxidation of methane to syngas for application in fuel cell electric vehicles (2003) Appl Catal A Gen, 243 (1), pp. 135-146Specchia, S., Vella, L.D., Montini, P., Fornasiero, P., Syngas production by short contact time catalytic partial oxidation of methane (2011) Hydrogen Production: Prospects and Processes, pp. 95-139. , D.R. Honnery, P. Moriarty, Nova Science Publishers Inc. New York ISBN: 978-1-62100-246-8Prette, M., Eichner, C.H., Perrin, M., The catalytic oxidation of methane to carbon monoxide and hydrogen (1946) T Faraday Soc, 42, pp. 335-339Horn, R., Williams, K.A., Degenstein, N.J., Bitsch-Larsen, A., Dallenogare, D., Tupy, S.A., Methane catalytic partial oxidation on autothermal Rh and Pt foam catalysts: Oxidation and reforming zones, transport effects, and approach to thermodynamic equilibrium (2007) J Catal, 249 (2), pp. 380-393Li, B., Maruyama, K., Nurunnabi, M., Kunimori, K., Tomishige, K., Temperature profiles of alumina-supported noble metal catalysts in autothermal reforming of methane (2004) Appl Catal A Gen, 275 (12), pp. 157-172Liu, T., Snyder, C., Veser, G., Catalytic partial oxidation of methane: Is a distinction between direct and indirect pathways meaningful (2007) Ind Eng Chem Res, 46 (26), pp. 9045-9052Dias, J.A.C., Assaf, J.M., Autothermal reforming of methane over Ni/γ-Al2O 3 catalysts: The enhancement effect of small quantities of noble metals (2004) J Power Sources, 130 (12), pp. 106-110Takeguchi, T., Furukawa, S.N., Inoue, M., Koichi, E., Autothermal reforming of methane over Ni catalyst supported over CaO-CeO2-ZrO2 solid solution (2003) Appl Catal A Gen, 240 (12), pp. 223-233Hagh, B.F., Stoichiometric analysis of autothermal fuel processing (2004) J Power Sources, 130 (12), pp. 85-94Rabe, S., Truong, T.B., Vogel, F., Catalytic autothermal reforming of methane: Performance of a kW scale reformer using pure oxygen as oxidant (2007) Appl Catal A Gen, 318, pp. 54-62Santos, D.C.R.M., Madeira, L., Passos, F.B., The effect of the addition of Y2O3 to Ni/α-Al2O3 catalysts on the autothermal reforming of methane (2010) Catal Today, 149 (34), pp. 401-406Liu, S., Xiong, G., Dong, H., Yang, W., Effect of carbon dioxide on the reaction performance of partial oxidation of methane over a LiLaNiO/γ-Al2O3 catalyst (2000) Appl Catal A Gen, 202 (1), pp. 141-146Liu, Z.W., Jun, K.W., Roh, H.S., Park, S.E., Hydrogen production for fuel cells through methane reforming at low temperatures (2002) J Power Sources, 111 (2), pp. 283-287Vagia, E.C., Lemonidou, A.A., Thermodynamic analysis of hydrogen production via autothermal steam reforming of selected components of aqueous bio-oil fraction (2008) Int J Hydrogen Energy, 33 (10), pp. 2489-2500Rodriguez, M.L., Ardissone, D.E., Pedernera, M.N., Borio, D.O., Influence of the oxygen feed distribution on the performance of a catalytic reactor for ATR of methane (2010) Catal Today, 156 (34), pp. 246-253Chen, W.H., Lin, M.R., Lu, J.J., Chao, Y., Leu, T.S., Thermodynamic analysis of hydrogen production from methane via autothermal reforming and partial oxidation followed by water gas shift reaction (2010) Int J Hydrogen Energy, 35 (21), pp. 11787-11797Li, Y., Wang, Y., Zhang, X., Mi, Z., Thermodynamic analysis of autothermal steam and CO2 reforming of methane (2008) Int J Hydrogen Energy, 33 (10), pp. 2507-2514Wang, H., Wang, X., Li, M., Li, S., Wang, S., Ma, X., Thermodynamic analysis of hydrogen production from glycerol autothermal reforming (2009) Int J Hydrogen Energy, 34 (14), pp. 5683-5690Michelsen, M.L., State function based flash specifications (1999) Fluid Phase Equilibr, 158-160, pp. 617-626Castier, M., Solution of the isochoric-isoenergetic flash problem by direct entropy maximization (2009) Fluid Phase Equilibr, 276 (1), pp. 7-17Rossi, C.C.R.S., Berezuk, M.E., Cardozo-Filho, L., Guirardello, R., Simultaneous calculation of chemical and phase equilibria using convexity analysis (2011) Comput Chem Eng, 35 (7), pp. 1226-1237Freitas, A.C.D., Guirardello, R., Oxidative reforming of methane for hydrogen and syntesisgás production: Thermodynamic equilibrium analysis (2012) J Nat Gas Chem, 21 (5), pp. 571-580Gao, J., Hou, Z., Liu, X., Zeng, Y., Luo, M., Zheng, X., Methane autothermal reforming with CO2 and O2 to synthesis gas at the boundary between Ni and ZrO2 (2009) Int J Hydrogen Energy, 34 (9), pp. 3734-3742Nurunnabi, M., Mukainakano, Y., Kado, S., Miyazawa, T., Okumura, K., Miyao, T., Oxidative steam reforming of methane under atmospheric and pressurized conditions over Pd/NiO-MgO solid solution catalysts (2006) Appl Catal A Gen, 308, pp. 1-12Choudhary, V.R., Mamman, A.S., Uphade, B.S., Steam and oxysteam reforming of methane to syngas over Co xNi1-xO supported on MgO precoated SA-5205 (2001) AIChE J, 47 (7), pp. 1632-1638Reese, M.A., Turn, S.Q., Cui, H., Kinetic modeling of high pressure autothermal reforming (2010) J Power Sources, 195 (2), pp. 553-558Simeone, M., Salemme, L., Allouis, C., Reactor temperature profile during autothermal methane reforming on Rh/Al2O3 catalyst by IR imaging (2008) Int J Hydrogen Energy, 33 (18), pp. 4798-4808Simeone, M., Salemme, L., Scognamiglio, D., Allouis, C., Volpicelli, G., Effect of water addition and stoichiometry variations on temperature profiles in an autothermal methane reforming reactor with Ni catalyst (2008) Int J Hydrogen Energy, 33 (4), pp. 1252-1261Ayabe, S., Omoto, H., Utaka, T., Kikuchi, R., Sasaki, K., Teraoka, Y., Catalytic autothermal reforming of methane and propane over supported metal catalysts (2003) Appl Catal A Gen, 241 (12), pp. 261-269Escritori, J.C., Dantas, S.C., Soares, R.R., Hori, C.E., Methane autothermal reforming nickel-ceria-zirconia based catalysts (2009) Catal Commun, 10 (7), pp. 1090-1094Souza, A.E.A.M., Maciel, L.J.L., Filho, M.L., Abreu, C.A.M., Catalytic activity evaluation for hydrogen production via autothermal reforming of methane (2010) Catal Today, 149 (34), pp. 413-417Hoang, D.L., Chan, S.H., Ding, O.L., Hydrogen production for fuel cells by autothermal reforming of methane over sulfide nickel catalyst on a gamma alumina support (2006) J Power Sources, 159 (2), pp. 1248-1257Dantas, S.C., Escritori, J.C., Soares, R.R., Hori, C.E., Effect of different promoters on Ni/CeZrO2 catalyst for autothermal reforming and partial oxidation of methane (2010) Chem Eng J, 156 (2), pp. 380-387DIADEM Public V. 1.2-DIPPR® - Information and Data Evaluation Manager, 2000, , Design Institute for Physical Property DataPoling, B.E., Prausnitz, J.M., O'Connell, P.J., (2000) The Properties of Gases and Liquids, , 5thed MacGraw Hill New YorkReid, R.C., Prausnitz, J.M., Poling, B.E., (1987) The Properties of Gases and Liquids, , 4thed MacGraw Hill New YorkReid, R.C., Prausnitz, J.M., Poling, B.E., (1977) The Properties of Gases and Liquids, , 3rded MacGraw Hill New YorkLiu, K., Song, C., Subramani, V., (2010) Hydrogen and Syngas Production and Purification Technologies, , John Wiley & Sons New JerseySpecchia, S., Francia, C., Spinelli, P., Polymer electrolyte membrane fuel cells (2011) Electrochemical Technologies for Energy Storage and Conversion, pp. 601-670. , R.S. Liu, L. Zhang, X. Sun, H. Liu, J. Zhang, Wiley-VHC Verlag GmbH & Co., KGaA Germany. WeinheimRuiz, J.A.C., Passos, F.B., Bueno, J.M.C., Souza-Aguiar, E.F., Mattos, L.V., Noronha, F.B., Syngas production by autothermal reforming of methane on supported platinum catalysts (2008) Appl Catal A Gen, 334 (12), pp. 259-267Adhikari, S., Fernando, S., Gwaltney, S.R., To, S.D.F., Bricka, R.M., Steele, P.H., A thermodynamic analysis of hydrogen production by steam reforming of glycerol (2007) Int J Hydrogen Energy, 32 (14), pp. 2875-2880Hoang, D.L., Chan, S.H., Modeling of a catalytic autothermal methane reformer for fuel cell applications (2004) Appl Catal A Gen, 268 (12), pp. 207-216Van Ness, H.C., Abbott, M.M., (1982) Classical Thermodynamics of Noneletrolyte Solutions: With Applications to Phase Equilibria, , MacGraw Hill New YorkSandler, S.I., (2006) Chemical, Biochemical, and Engineering Thermodynamics, p. 32. , 4th ed. John Wiley & Sons In
    corecore