Setting up a PDPA system for measurements in a Diesel spray

Abstract. A PDPA system was set up, optimised and used to measure the time resolved characteristics of the droplets inside a spray produced by a common-rail diesel fuel injection system. Some preliminary tests are performed with gas flows to optimise the optical set-up. Parametric studies are performed to gain an understanding of the particle density limits of the system, and their dependence on PDPA system parameters. Then the diesel spray produced by a single-hole injector is measured, with the fuel pressure ranging from 500 to 1300 bar, gas density in the test chamber ranging from ambient conditions to 40 kg/m3. Fuel and gas temperature were 25ºC. Beam waist size is reduced to the minimum value allowed by the optical stand-off of the spray enclosure. Receiver lens focal length is similarly reduced. Receiver slit width, which is found to have a dramatic effect on the detection of droplets during the injection period, was tested in the range from 100um to 25um. Tests performed with two different slit heights are tested, respectively 1mm and 50 μm, show that this parameter has minimal effect on performance. PMT voltage (gain) is held to a moderately low value between 400 and 500 volt and the laser power between 400 and 800 mW in the green line. Optimum burst threshold is found to obtain the best quality data regardless of background level, which varies greatly in high-density pulsed sprays

Elektrokemijski postupak za proizvodnju titanovih kompozitnih slitina

The paper presents a new method for precursors’ synthesis of titanium alloys matrix composites through an electrochemical process in molten calcium chloride. The cathode of the cell was made from metallic oxides powders and reinforcement ceramic particles, which were pressed and sintered into disk form and the anode from graphite. The process occurred at 850 °C, in two stages, at 2,7 / 3,2 V: the ionization of the oxygen in oxides and the reduction with calcium formed by electrolysis of calcium oxide fed in the electrolyte. The obtained composite precursors, in a form of metallic sponge, were consolidated by pressing and sintering. Chemical and structural analyses on composites samples were performed.Članak prikazuje novu metodu prethodne sinteze titanovih kompozitnih slitina s elektrokemijskim postupkom u rastaljenom kalcijevom kloridu. Katoda ćelije ustrojena je od praškastog metalnog oksida ojačan keramičkim česticama, koji je stlačen u obliku diska, a anoda je od grafita. Postupak se odvijao na 850 °C u dva stupnja, 2,7/3,2 V: ionizacija kisika u oksidima i redukcija kalcijem nastajala je elektrolizom kalcijevih oksida u elektrolitu. Dobiveni prethodno kompozit u obliku metalne spužve je očvrsnut tlačenjem i sinteriranjem. Provedena je kemijska i strukturna analiza uzoraka kompozita

Study of the Mg-Nd alloy obtained by electrolysis in molten oxifluoride media

Mg-Nd alloys have been produced by electrolysis of the molten mixture LiF-NdF3-MgF2 using Nd2(CO3)3 and MgF2 as raw materials. An electrolysis cell was designed having the anode made of super dense graphite and the cathode made of molybdenum metal. The quasi-binary system (NdF3-LiF)eutectic-MgF2 was investigated and the liquidus line was determined using thermo-differential analysis. The solubility of Nd2(CO3)3 in the LiF-NdF3-MgF2 system was investigated by the carbothermal technique

Синдром хронической сердечной недостаточности вторичной Тетраде Фалло: клинические и диагностические аспекты на основе одного случая

Department of Pediatrics, Nicolae Testemitanu State Medical and Pharmaceutical University, Congresul III al Medicilor de Familie din Republica Moldova, 17–18 mai, 2012, Chişinău, Republica Moldova, Conferinţa Naţională „Maladii bronhoobstructive la copii”, consacrată profesorului universitar, doctor habilitat Victor Gheţeul, 27 aprilie, Chişinău, Republica MoldovaThe authors present a clinical case of a 17 year old boy, which in his clinical and paraclinical data highlighted the following diagnostic: Congenital heart failure; Tetralogy of Fallot; AV Block gr. III; Mitral valve insufficiency gr. IV; Tricuspid valve insufficiency gr. IV; Heart failure NYHA functional class gr. III-IV. The case focuses on complications that may occur in late cardio surgeries and the development of AV block gr. III disorders. If complications arose during the evolution of the disease, there would have been performed multiple pacemaker reimplantations. The article insists on the way how cardiovascular complications start as much as on the importance of prompt medical supervision to ensure the patient’s quality of life.В данной статье описан клинический случай ребёнка в возрасте 17 лет, у которого по клинико-инструментальным данным был установлен клинический диагноз – врожденный порок сердца, Tетрада Фалло, aтриовентрикулярная блокада III-ей степени. Имплантация исскуственного кардиостимулятора ритма сердца (1998, 2002, 2007). Недостаточность митрального клапана IV-ой степени. Недостаточность трикуспидального клапана IV-ой степени. НК IV NYHA

Construire les fonctions récursives totales en Coq

International audienceWe present a (relatively) short mechanized proof that Coq types any recursive function which is provably total in Coq. The well-founded (and terminating) induction scheme, which is the foundation of Coq recursion, is maximal. We implement an unbounded minimization scheme for decidable predicates. It can also be used to reify a whole category of undecidable predicates. This development is purely constructive and requires no axiom. Hence it can be integrated into any project that might assume additional axioms

Evaluation of natural and tracer fluorescent emission methods for droplet size measurements in a diesel spray

The final publication is available at Springer via http://dx.doi.org/10.1007/s12239-012-0070-zSpray sizing that records fluorescent emission and scattered light has been widely applied to spray diagnostics over the last two decades. Different experimental strategies have been developed, but comparing the different solutions offered has remained of interest to experimentalists. In this work, a comparison of two fluorescence strategies for measuring droplet size in the liquid phase of a last-generation DI diesel spray is conducted. The natural fluorescent emission of a commercial diesel fuel and the fluorescence emitted by a tracer (Rhodamine B) are compared using theoretical and experimental approaches. The LIF/Mie ratio commonly called Planar Droplet Sizing (PDS) technique is applied in two different ways to elucidate the possible advantages of using a fluorescent dopant. The sprays were injected under non-evaporative conditions into a constant pressure vessel that simulates densities present at the moment of injection in currently used passenger car diesel engines. Characterization of the signal properties was performed by measuring the absorption coefficient, fluorescence emission spectrum, quantum yield and lifetime of both configurations. The scattered light and fluorescence intensities were calculated to verify the dependencies of the droplet surface and volume. When applying the two techniques to quantify droplet size in dense diesel sprays, the results show that signal weakness and lack of control over the properties of natural fluorescence produce distortion in the shape of the spray and cause measurements to be unreliable. © 2012 The Korean Society of Automotive Engineers and Springer-Verlag Berlin Heidelberg.This research has been funded in the frame of the project PROFUEL reference TRA2011-26293 from Ministerio de Ciencia e Innovacion. The injectors are part of the ECN international project.Pastor Soriano, JV.; Payri, R.; Salavert Fernandez, J.; Manin, J. (2012). Evaluation of natural and tracer fluorescent emission methods for droplet size measurements in a diesel spray. International Journal of Automotive Technology. 13(5):713-724. https://doi.org/10.1007/s12239-012-0070-zS713724135Albrecht, H. E., Damaschke, N., Borys, M. and Tropea, C. (2003). Laser Doppler and Phase Doppler Measurement Techniques. Springer. Berlin.Barnes, M. D., Whitten, W. B. and Ramsey, J. M. (1994). Enhanced fluorescence yields through cavity quantumelectrodynamic effects in microdroplets. J. Optical Society of America B 11,7, 1297–1304.Benajes, J., Molina, S., Novella, R., Amorim, R., Ben Hadj Hamouda, H. and Hardy, J. (2010). Comparison of two injection systems in an HSDI diesel engine using split injection and different injector nozzles. Int. J. Automotive Technology 11,2, 139–146.Charalampous, G. and Hardalupas, Y. (2011). Method to reduce errors of droplet sizing based on the ratio of fluorescent and scattered light intensities (laser-induced fluorescence/Mie technique). Applied Optics, 50, 3622–3637.Chen, G., Mazumder, M., Chang, R. K., Swindal, J. C. and Acker, W. P. (1996). Laser diagnostics for droplet characterization: Application of morphology dependent resonances. Progress in Energy and Combustion Science 22,2, 163–188.Desantes, J. M., Payri, R., Garcia, J. M. and Salvador, F. J. (2007). A contribution to the understanding of isothermal diesel spray dynamics. Fuel 86,7–8, 1093–1101.Domann, R. and Hardalupas, Y. A. (2000). Study of parameters that influence the accuracy of the planar droplet sizing (PDS) technique. Part. Part. Syst. Charact. 3–11.Domann, R. and Hardalupas, Y. A. (2001). Spatial distribution of fluorescence within large doplets and its dependence on dye concentration. Applied Optics 40,21, 3586–3597.Domann, R. and Hardalupas, Y. A. (2002). Quantitative measurement of planar droplet sauter mean diameter in sprays using planar droplet sizing. 11th Int. Symp. Application of Laser Techniques to Fluid Mechanics, Lisbon, Portugal.Eckbreth, A. C. (1988). Laser Diagnostics for Combustion Species and Temperature. Abacus. Cambridge. Mass.Greenhalgh, D. A. (1999). Planar measurements of fuel vapour, liquid fuel, liquid droplet size and soot. Planar Optical Measurement Methods for Gas Turbine Components, 1–7.Im, K., Lin, K., Lai, M. and Chon, M. (2011). Breakup modeling of a liquid jet in cross flow. Int. J. Automotive Technology 12,4, 489–496.Jermy, M. C. and Greenhalgh, D. A. (2000). Planar dropsizing by elastic and fluorescence scattering in sprays too dense for phase doppler measurement. Appl. Phys. B, 71, 703–710.Kim, Y., Kim, K. and Lee, K. (2011). Effect of a 2-stage injection strategy on the combustion and flame characteristics in a PCCI engine. Int. J. Automotive Technology 12,5, 639–644.Ko, F. H., Weng, L. Y., Ko, C. J. and Chu, T. C. (2006). Characterization of imprinting polymeric temperature variation with fluorescent Rhodamine B molecule. Microelectronic Engineering, 83, 864–868.Lakowicz, J. R. (2006). Principles of Fluorescence Spectroscopy. 3rd Edn. Springer.Lee, S. H., Teong, J., Lee, J. T., Ryou, H. S. and Hong, K. (2005). Investigation on spray characteristics under ultrahigh injection pressure conditions. Int. J. Automotive Technology 6,2, 125–131.Lee, B., Song, J., Chang, Y. and Jeon, C. (2010). Effect of the number of fuel injector holes on characteristics of combustion and emissions in a diesel engine. Int. J. Automotive Technology 11,6, 783–791.LeGal, P., Farrugia, N. and Greenhalgh, D. A. (1999). Laser sheet dropsizing of dense sprays. Optics and Laser Techn., 31, 75–83.Lockett, R. D., Richter, J. and Greenhalgh, D. A. (1998). The characterisation of a diesel spray using combined laser induced fluorescence and laser sheet dropsizing. Conf. Lasers and Electro-Optics Europe.Magde, D., Rojas, G. E. and Seybold, P. (1999). Solvent dependence of the fluorescence lifetimes of xanthene dyes. Photochem. Photobiol., 70, 737.Naber, J. and Siebers, D. (1996). Effects of gas density and vaporization on penetration and dispersion of diesel sprays. SAE Paper No. 960034.Pastor, J. V., López, J. J., Juliá, J. E. and Benajes, J. V. (2002). Planar laser-induced fluorescence fuel concentration measurements in isothermal diesel sprays. Opt. Express 10,7, 309–323.Pastor, J. V., Payri, R., Araneo, L. and Manin, J. (2009). Correction method for droplet sizing by laser-induced fluorescence in a controlled test situation. Optical Engineering 48,1, 013601.Payri, R., Garcia, J. M., Salvador, F. J. and Gimeno, J. (2005a). Using spray momentum flux measurements to understand the influence of diesel nozzle geometry on spray characteristics. Fuel, 84, 551–561.Payri, R., Salvador, F. J., Gimeno, J. and Soare, V. (2005b). Determination of diesel sprays characteristics in real engine in-cylinder air density and pressure conditions. J. Mech. Sci. Technol., 19, 2040–2052.Payri, R., Tormos, B., Salvador, F. J. and Araneo, L. (2008). Spray droplet velocity characterization for convergent nozzles with three different diameters. Fuel 87,15, 3176–3182.Payri, F., Pastor, J., Payri, R. and Manin, J. (2011). Determination of the optical depth of a DI diesel spray. J. Mech. Sci. Technol., 25, 209–219.Potz, D., Chirst, W. and Dittus, B. (2000). Diesel nozzle: The determining interface between injection system and combustion chamber. Conf. Thermo and Fluid-dynamic Processes in Diesel Engines, Valencia, Spain.Ramírez, A. I., Som, S., Aggarwal, S. K., Kastengren, A. L., El-Hannouny, E. M., Longman, D. E. and Powell, C. F. (2009). Quantitative X-ray measurements of highpressure fuel sprays from a production heavy duty diesel injector. Experiments in Fluids 47,1, 119–134.Schulz, C. and Sick, V. (2005). Tracer-LIF diagnostics: quantitative measurement of fuel concentration, temperature and fuel/air ratio in practical combustion systems. Progress in Energy and Combustion Science, 31, 75–121.Sjoback, R. and Nygren, J. and Kubista, M. (1998). Characterization of fluorescein—oligonucleotide conjugates and measurement of local electrostatic potential. Biopolymers, 46, 445–453.Soare, V. (2007). Phase Doppler Measurement in Diesel Dense Sprays: Optimisation of Measurements and Study of the Orifice Geometry Influence Over the Spray at Microscopic Level. Ph.D. Dissertion. E.T.S. Ingenieros Industriales. Universidad Politécnica de Valencia. Spain.Williams, A. T. R., Winfield, S. A. and Miller, J. N. (1983). Relative fluorescence quantum yields using a computer controlled luminescence spectrometer. Analyst., 108, 1067.Yeh, C. N., Kosaka, H. and Kamimoto, T. A. (1993). Fluorescence/scattering imaging technique for instantaneous 2-D measurements of particle size distribution in a transient spray. Proc. 3rd Cong. Opt. Part. Sizing, Yokohama, Japan, 335–361

Supervolcanoes Within an Ancient Volcanic Province in Arabia Terra, Mars

Several irregularly shaped craters located within Arabia Terra, Mars represent a new type of highland volcanic construct and together constitute a previously unrecognized martian igneous province. Similar to terrestrial supervolcanoes, these low-relief paterae display a range of geomorphic features related to structural collapse, effusive volcanism, and explosive eruptions. Extruded lavas contributed to the formation of enigmatic highland ridged plains in Arabia Terra. Outgassed sulfur and erupted fine-grained pyroclastics from these calderas likely fed the formation of altered, layered sedimentary rocks and fretted terrain found throughout the equatorial region. Discovery of a new type of volcanic construct in the Arabia volcanic province fundamentally changes the picture of ancient volcanism and climate evolution on Mars. Other eroded topographic basins in the ancient Martian highlands that have been dismissed as degraded impact craters should be reconsidered as possible volcanic constructs formed in an early phase of widespread, disseminated magmatism on Mars

Complex type 4 structure changing dynamics of digital agents: Nash equilibria of a game with arms race in innovations

The new digital economy has renewed interest in how digital agents can innovate. This follows the legacy of John von Neumann dynamical systems theory on complex biological systems as computation. The Gödel-Turing-Post (GTP) logic is shown to be necessary to generate innovation based structure changing Type 4 dynamics of the Wolfram-Chomsky schema. Two syntactic procedures of GTP logic permit digital agents to exit from listable sets of digital technologies to produce novelty and surprises. The first is meta-analyses or offline simulations. The second is a fixed point with a two place encoding of negation or opposition, referred to as the Gödel sentence. It is postulated that in phenomena ranging from the genome to human proteanism, the Gödel sentence is a ubiquitous syntactic construction without which escape from hostile agents qua the Liar is impossible and digital agents become entrained within fixed repertoires. The only recursive best response function of a 2-person adversarial game that can implement strategic innovation in lock-step formation of an arms race is the productive function of the Emil Post [58] set theoretic proof of the Gödel incompleteness result. This overturns the view of game theorists that surprise and innovation cannot be a Nash equilibrium of a game

Programme Dementia Prevention (pdp): A Nationwide Program for Personalized Prevention in Luxembourg.

peer reviewedBACKGROUND: With continuously aging societies, an increase in the number of people with cognitive decline is to be expected. Aside from the development of causative treatments, the successful implementation of prevention strategies is of utmost importance to reduce the high societal burden caused by neurodegenerative diseases leading to dementia among which the most common cause is Alzheimer's disease. OBJECTIVE: The aim of the Luxembourgish "programme dementia prevention (pdp)" is to prevent or at least delay dementia in an at-risk population through personalized multi-domain lifestyle interventions. The current work aims to provide a detailed overview of the methodology and presents initial results regarding the cohort characteristics and the implementation process. METHODS: In the frame of the pdp, an extensive neuropsychological evaluation and risk factor assessment are conducted for each participant. Based on the results, individualized multi-domain lifestyle interventions are suggested. RESULTS: A total number of 450 participants (Mean age = 69.5 years; SD = 10.8) have been screened at different recruitment sites throughout the country, among whom 425 participants (94.4%) met the selection criteria. CONCLUSIONS: We provide evidence supporting the feasibility of implementing a nationwide dementia prevention program and achieving successful recruitment of the target population by establishing a network of different healthcare providers.3. Good health and well-bein

On the mechanisms governing gas penetration into a tokamak plasma during a massive gas injection

A new 1D radial fluid code, IMAGINE, is used to simulate the penetration of gas into a tokamak plasma during a massive gas injection (MGI). The main result is that the gas is in general strongly braked as it reaches the plasma, due to mechanisms related to charge exchange and (to a smaller extent) recombination. As a result, only a fraction of the gas penetrates into the plasma. Also, a shock wave is created in the gas which propagates away from the plasma, braking and compressing the incoming gas. Simulation results are quantitatively consistent, at least in terms of orders of magnitude, with experimental data for a D 2 MGI into a JET Ohmic plasma. Simulations of MGI into the background plasma surrounding a runaway electron beam show that if the background electron density is too high, the gas may not penetrate, suggesting a possible explanation for the recent results of Reux et al in JET (2015 Nucl. Fusion 55 093013)