3,727 research outputs found
The effect of chine tires on nose gear water-spray characteristics of a twin engine airplane
An experimental investigation was performed to evaluate the effectiveness of nose gear chine tires in eliminating or minimizing the engine spray ingestion problem encountered on several occasions by the Merlin 4, a twin-engine propjet airplane. A study of the photographic and television coverage indicated that under similar test conditions the spray from the chine tires presented less of a potential engine spray ingestion problem than the conventional tires. Neither tire configuration appeared to pose any ingestion problem at aircraft speeds in excess of the hydroplaning speed for each tire, however, significant differences were noted in the spray patterns of the two sets of tires at sub-hydroplaning speeds. At sub-hydroplaning speeds, the conventional tires produced substantial spray above the wing which approached the general area of the engine air inlet at lower test speeds. The chine tires produced two distinct spray plumes at sub-hydroplaning speeds: one low-level plume which presented no apparent threat of ingestion, and one which at most test speeds was observed to be below the wing leading edge and thus displaced from the intakes on the engine nacelle
Static and yawed-rolling mechanical properties of two type 7 aircraft tires
Selected mechanical properties of 18 x 5.5 and 49 x 17 size, type 7 aircraft tires were evaluated. The tires were subjected to pure vertical loads and to combined vertical and lateral loads under both static and rolling conditions. Parameters for the static tests consisted of tire load in the vertical and lateral directions, and parameters for the rolling tests included tire vertical load, yaw angle, and ground speed. Effects of each of these parameters on the measured tire characteristics are discussed and, where possible, compared with previous work. Results indicate that dynamic tire properties under investigation were generally insensitive to speed variations and therefore tend to support the conclusion that many tire dynamic characteristics can be obtained from static and low speed rolling tests. Furthermore, many of the tire mechanical properties are in good agreement with empirical predictions based on earlier research
Choosing treatment for localised prostate cancer: A patient-conducted-interview study
Objectives: Treatment choice can be particularly difficult in localised prostate cancer because of the uncertainty involved. Indeed, some men prefer maintaining their masculine identity and quality of life to potentially securing longer-term survival through surgery or radiotherapy. UK health services are now obliged to leave the choice of treatment to the patient and the aim of this study is to improve understanding of patients’ experiences of choosing treatment. Methods: A one-day participative workshop where men of six months post-diagnosis design and conduct audio and video interviews on each other about their experiences of choosing treatment. Results: The findings show that treatment choice is a complex process combining emotional and rational elements. Information gathering and delegation to professional expertise were two key themes that emerged. Conclusions: The findings emphasise that treatment choice for localised prostate cancer is little like the traditional notions of consumerism from which it is derived. Importantly, the results illustrate, from a patient perspective, how health professionals can engage in their roles as information providers and as experts
Charging and Subsequent Dissipation of a Rover Wheel in the Lunar Polar Regions
As a roving vehicle moves along the lunar surface, electric charge will build up through tribo-charging. This charge collected by the roving object will have a dissipative path to either the surface or the ambient plasma, depending upon which path is most conductive. At the lunar terminator region and into nightside regions, the surface is very cold and becomes a very poor conductor. leaving the plasma as the dominant remediating current for dissipation. However, within lunar craters, even plasma currents become substantially reduced which then greatly increases electric 'dissipation times, This work will involve the advancement of the stepping astronaut charge model, by considering the charging and plasma dissipation of a rolling rover wheel, The objective of this work is to determine the nature of charging and discharging for a rover wheel as it rolls along the cold, plasma-starved lunar polar regions. The rotating wheel accumulates charge via contact electrification (tribo-charging) with the lunar regolith. This tribo-charging is dependent on the composition of the objects in contact, with insulators and conductors charging differently. Given the environmental plasma in the region, we then determine the dissipation time for the wheel to bleed off its excess charge into the surrounding plasma. A model of the rover wheel rotating continuously over a surface regolith within a polar crater has been applied. The environmental plasma has been described previously. We define a new tribo-charging term specifically for the rotating system, with charge levels defined as a function of the wheel size, area in contact with the regolith, regolith particle size distribution, as well as the velocity at which the wheel is turning. We recognize that as charged dust accumulates and sticks to the wheel, this behaves effectively as a new current. Hence, the overall charging of the system should no longer vary linearly. and begin to show signs of saturation, We are devising a dust current term to model this charge-limiting effect, and will present the results in discussion
Pressure ulcer related pain in community populations: a prevalence survey.
BACKGROUND: Pressure ulcers are costly to the healthcare provider and can have a major impact on patient's quality of life. One of the most distressing symptoms reported is pain. There is very little published data on the prevalence and details of pain experienced by patients with pressure ulcers, particularly in community populations. The study was conducted in two community NHS sites in the North of England. METHODS: The aim was to estimate the prevalence of pressure area related pain within a community population. We also explored the type and severity of the pain and its association with pressure ulcer classification. A cross-sectional survey was performed of community nurses caseloads to identify adult patients with pressure ulcers and associated pain. Consenting patients then had a full pain assessment and verification of pressure ulcer grade. RESULTS: A total of 287 patients were identified with pressure ulcers (0.51 per 1000 adult population). Of the 176 patients who were asked, 133 (75.6%) reported pain. 37 patients consented to a detailed pain assessment. Painful pressure ulcers of all grades and on nearly all body sites were identified. Pain intensity was not related to number or severity of pressure ulcer. Both inflammatory and neuropathic pain were reported at all body sites however the proportion of neuropathic pain was greater in pressure ulcers on lower limbs. CONCLUSIONS: This study has identified the extent and type of pain suffered by community patients with pressure ulcers and indicates the need for systematic and regular pain assessment and treatment
The Impact of Collaborative Modalities on Wireless Robotics
Many mathematicians would agree that, had it not been for evolutionary programming, the refinement of the UNIVAC computer might never have occurred. In our research, we disconfirm the investigation of SCSI disks, which embodies the technical principles of theory [28, 6, 18]. In our research, we examine how journaling file systems can be applied to the synthesis of Boolean logic
funcX: A Federated Function Serving Fabric for Science
Exploding data volumes and velocities, new computational methods and
platforms, and ubiquitous connectivity demand new approaches to computation in
the sciences. These new approaches must enable computation to be mobile, so
that, for example, it can occur near data, be triggered by events (e.g.,
arrival of new data), be offloaded to specialized accelerators, or run remotely
where resources are available. They also require new design approaches in which
monolithic applications can be decomposed into smaller components, that may in
turn be executed separately and on the most suitable resources. To address
these needs we present funcX---a distributed function as a service (FaaS)
platform that enables flexible, scalable, and high performance remote function
execution. funcX's endpoint software can transform existing clouds, clusters,
and supercomputers into function serving systems, while funcX's cloud-hosted
service provides transparent, secure, and reliable function execution across a
federated ecosystem of endpoints. We motivate the need for funcX with several
scientific case studies, present our prototype design and implementation, show
optimizations that deliver throughput in excess of 1 million functions per
second, and demonstrate, via experiments on two supercomputers, that funcX can
scale to more than more than 130000 concurrent workers.Comment: Accepted to ACM Symposium on High-Performance Parallel and
Distributed Computing (HPDC 2020). arXiv admin note: substantial text overlap
with arXiv:1908.0490
- …