4,824 research outputs found

    Scanning Optical Microscopy of Semiconductor Materials and Devices

    Get PDF
    In the scanning optical microscope a focused light spot is used to illuminate the object and some property monitored as the spot is scanned relative to the object to build up an image. By monitoring different properties it is thus possible to use the scanning optical microscope in a wide range of imaging modes, which can be used to give much information concerning the structure and properties of semiconductor materials and devices. In the optical-beam induced current method the focused light spot generates electronic carriers in a semiconductor specimen, and the resultant current monitored. The technique can be used to study defects in semiconducting materials and to measure electronic properties. If instead the reflected light is monitored we can obtain images in which resolution, contrast and depth of focus are all improved relative to conventional optical microscopy. Using the confocal imaging mode surface topography of thick structures can be investigated. In the scanning optical microscope we gain all these advantages whilst avoiding the disadvantageous effects of an electron beam and the necessity for a vacuum environment

    Development of autoclavable addition type polyimides

    Get PDF
    Two highly promising approaches to yield autoclavable addition-type polyimides were identified and evaluated in the program. Conditions were established for autoclave preparation of Hercules HMS graphite fiber reinforced composites in the temperature range of 473 K to 505 K under an applied pressure of 0.7 MN/m2 (100 psi) for time durations up to four hours. Upon oven postcure in air at 589 K, composite samples demonstrated high mechanical property retention at 561 K after isothermal aging in air for 1000 hours. Promise was shown for shorter term mechanical property retention at 589 K upon exposure in air at this temperature

    Development of autoclavable polyimides

    Get PDF
    A poly(Diels-Alder) (PDA) resin approach was investigated as a means to achieve autoclavability of high temperature resistant resin/fiber composites under mild fabrication procedures. Low void content Type A-S graphite reinforced composites were autoclave fabricated from a PDA resin/fiber prepared from an acetone:methanol:dioxane varnish. Autoclave conditions were 477K (400F) and 0.7 MN/sq m (100 psi) for up to two hours duration. After postcure at temperatures up to 589K (600F), the composites demonstrated high initial mechanical properties at temperatures up to 561K (550F). The results from isothermal aging studies in air for 1000 hours indicated potential for long-term ( 1000 hours) use at 533K (500F) and shorter-term (up to 1000 hours) at 561K (550F)

    Improved expressions for performance parameters for complex filters

    Get PDF
    Improved expressions are given for the performance parameters for transverse and axial gains for complex pupil filters. These expressions can be used to predict the behavior of filters that give a small axial shift in the focal intensity maximum and also predict the changes in gain for different observation planes

    Lorentz Beams

    Full text link
    A new kind of tridimensional scalar optical beams is introduced. These beams are called Lorentz beams because the form of their transverse pattern in the source plane is the product of two independent Lorentz functions. Closed-form expression of free-space propagation under paraxial limit is derived and pseudo non-diffracting features pointed out. Moreover, as the slowly varying part of these fields fulfils the scalar paraxial wave equation, it follows that there exist also Lorentz-Gauss beams, i.e. beams obtained by multipying the original Lorentz beam to a Gaussian apodization function. Although the existence of Lorentz-Gauss beams can be shown by using two different and independent ways obtained recently from Kiselev [Opt. Spectr. 96, 4 (2004)] and Gutierrez-Vega et al. [JOSA A 22, 289-298, (2005)], here we have followed a third different approach, which makes use of Lie's group theory, and which possesses the merit to put into evidence the symmetries present in paraxial Optics.Comment: 11 pages, 1 figure, submitted to Journal of Optics

    Variation of turbulent burning rate of methane, methanol, and iso-octane air mixtures with equivalence ratio at elevated pressure

    Get PDF
    Turbulent burning velocities for premixed methane, methanol, and iso-octane/air mixtures have been experimentally determined for an rms turbulent velocity of 2 m/s and pressure of 0.5 MPa for a wide range of equivalence ratios. Turbulent burning velocity data were derived using high-speed schlieren photography and transient pressure recording; measurements were processed to yield a turbulent mass rate burning velocity, utr. The consistency between the values derived using the two techniques, for all fuels for both fuel-lean and fuel-rich mixtures, was good. Laminar burning measurements were made at the same pressure, temperature, and equivalence ratios as the turbulent cases and laminar burning velocities and Markstein numbers were determined. The equivalence ratio (φ) for peak turbulent burning velocity proved not always coincident with that for laminar burning velocity for the same fuel; for isooctane, the turbulent burning velocity unexpectedly remained high over the range φ = 1 to 2. The ratio of turbulent to laminar burning velocity proved remarkably high for very rich iso-octane/air and lean methane/air mixtures

    Perfect Reflection of Light by an Oscillating Dipole

    Full text link
    We show theoretically that a directional dipole wave can be perfectly reflected by a single point-like oscillating dipole. Furthermore, we find that in the case of a strongly focused plane wave up to 85 % of the incident light can be reflected by the dipole. Our results hold for the full spectrum of the electromagnetic interactions and have immediate implications for achieving strong coupling between a single propagating photon and a single quantum emitter.Comment: 3 figure

    Thermal simulation of magnetization reversals for size-distributed assemblies of core-shell exchange biased nanoparticles

    Full text link
    A temperature dependent coherent magnetization reversal model is proposed for size-distributed assemblies of ferromagnetic nanoparticles and ferromagnetic-antiferromagnetic core-shell nanoparticles. The nanoparticles are assumed to be of uniaxial anisotropy and all aligned along their easy axis. The thermal dependence is included by considering thermal fluctuations, implemented via the N\'eel-Arrhenius theory. Thermal and angular dependence of magnetization reversal loops, coercive field and exchange-bias field are obtained, showing that F-AF size-distributed exchange-coupled nanoparticles exhibit temperature-dependent asymmetric magnetization reversal. Also, non-monotonic evolutions of He and Hc with T are demonstrated. The angular dependence of Hc with T exhibits a complex behavior, with the presence of an apex, whose position and amplitude are strongly T dependent. The angular dependence of He with T exhibits complex behaviors, which depends on the AF anisotropy and exchange coupling. The resulting angular behavior demonstrates the key role of the size distribution and temperature in the magnetic response of nanoparticles.Comment: Revised arguments in Introduction and last sectio
    corecore