8,512 research outputs found
Benthic habitat mapping in the Olympic Coast National Marine Sanctuary: Classification of side scan sonar data from survey HMPR-108-2002-01: Version I
In September 2002, side scan sonar was used to image a portion of the sea floor in the northern OCNMS and was mosaiced at 1-meter pixel resolution using 100 kHz data
collected at 300-meter range scale. Video from a remotely-operated vehicle (ROV), bathymetry data, sedimentary samples, and sonar mapping have been integrated to
describe geological and biological aspects of habitat and polygon features have been created and attributed with a hierarchical deep-water marine benthic classification
scheme (Greene et al. 1999). The data can be used with geographic information system (GIS) software for display, query, and analysis. Textural analysis of the sonar images
provided a relatively automated method for delineating substrate into three broad classes representing soft, mixed sediment, and hard bottom. Microhabitat and presence of
certain biologic attributes were also populated into the polygon features, but strictly limited to areas where video groundtruthing occurred. Further groundtruthing work in
specific areas would improve confidence in the classified habitat map. (PDF contains 22 pages.
Olympic Coast National Marine Sanctuary Habitat Mapping: Survey report and classification of side scan sonar data from surveys HMPR-114-2004-02 and HMPR-116-2005-01.
The Olympic Coast National Marine Sanctuary (OCNMS) continues to invest significant resources into seafloor mapping activities along Washington’s outer coast (Intelmann and Cochrane 2006; Intelmann et al. 2006; Intelmann 2006). Results from these annual mapping efforts offer a snapshot of current ground conditions, help to guide research and management activities, and provide a baseline for assessing the impacts of various threats
to important habitat. During the months of August 2004 and May and July 2005, we used side scan sonar to image several regions of the sea floor in the northern OCNMS, and the
data were mosaicked at 1-meter pixel resolution. Video from a towed camera sled, bathymetry data, sedimentary samples and side scan sonar mapping were integrated to describe geological and biological aspects of habitat. Polygon features were created and attributed with a hierarchical deep-water marine benthic classification scheme (Greene et
al. 1999). For three small areas that were mapped with both side scan sonar and multibeam echosounder, we made a comparison of output from the classified images indicating little difference in results between the two methods. With these considerations, backscatter derived from multibeam bathymetry is currently a costefficient and safe method for seabed imaging in the shallow (<30 meters) rocky waters of
OCNMS. The image quality is sufficient for classification purposes, the associated depths provide further descriptive value and risks to gear are minimized. In shallow waters (<30 meters) which do not have a high incidence of dangerous rock pinnacles, a towed multi-beam side scan sonar could provide a better option for obtaining seafloor
imagery due to the high rate of acquisition speed and high image quality, however the high probability of losing or damaging such a costly system when deployed as a towed
configuration in the extremely rugose nearshore zones within OCNMS is a financially risky proposition. The development of newer technologies such as intereferometric
multibeam systems and bathymetric side scan systems could also provide great potential for mapping these nearshore rocky areas as they allow for high speed data acquisition,
produce precisely geo-referenced side scan imagery to bathymetry, and do not experience the angular depth dependency associated with multibeam echosounders allowing larger range scales to be used in shallower water. As such, further investigation of these systems is needed to assess their efficiency and utility in these environments compared to traditional side scan sonar and multibeam bathymetry. (PDF contains 43 pages.
Tourism for Protected Area Financing: Understanding tourism revenues for effective management plans
Where Have All the Young Girls Gone? Identification of Sex Selection in India
This paper presents the first estimates of the causal effect of facilities for prenatal sex diagnosis on the sex ratio at birth in India. It conducts a triple difference analysis across cohort, birth order and sex of previous births. Treated births are those that occur after prenatal sex detection becomes available at birth order two or more in families that have not yet had their desired number of sons (or daughters). The three implied control groups are births that occur pre-ultrasound, births of first order and births that occur after the family has achieved its desired sex mix of births. We identify a significant divergence between the treated and control groups. We consider alternative hypotheses and conduct an array of robustness checks to show that the divergence of the sex ratio of the treated group from the normal biological range that characterizes the control groups is on account of female foeticide. We estimate that as many as 0.48 million girls p.a. were selectively aborted during 1995-2005, which is more than the number of girls born in the UK each year. The estimates suggest that Indian families desire two boys and a girl; previous studies often assume that the desire is for at least one boy. The incentive to conduct sex selection is increasing in birth order and family socioeconomic status, both consistent with stronger incentives to sex-select as fertility approaches its target.sex selection, abortion, sex ratio, son preference, prenatal sex diagnosis, ultrasound, gender, India, triple difference estimator, differences in differences
A contribution to the discussion on the safety of air weapons
Firearms legislation in the UK stems from the Firearms Act 1968 with its definition of a firearm as a lethal barrelled weapon of any description. The Act allows certain exceptions to be held without licence, most notably air weapons although these are limited by The Firearms (Dangerous Air Weapons) Rules 1969 and related regulations to below 12 ft lb (16.3 J) for air rifles and below 6 ft lb (8.1 J) for air pistols. Despite this there are occasional fatalities, typically 1 or 2 each year in the UK, from legally owned air weapons. In the USA there are over 20,000 visits each year to emergency departments due to injuries from air weapons and paintball guns. Despite this, limited research appears to have been carried out into the safety of air weapons and the present study tries to address this.Fresh samples of animal tissue were obtained from an abattoir or butcher and were embedded in ballistic gelatin. Pig heart, lung, liver and shoulder were used. By firing pellets into gelatin alone and into the combination of the gelatin and animal tissue it was possible to compare gelatin as a model for these tissues. The depth of penetration was similar but the residual track appeared to remain more open in the animal tissue. Pellets penetrated completely through the organ, with total penetration of gelatin and organ being typically around 10–15 cm.Samples of pig, cow and chicken skin were placed in contact with the gelatin or embedded in the gelatin to simulate the effect of skin on penetration into a body. Chicken skin had no effect, pig skin stopped the pellet and cow skin was perforated by the pellet. If cow skin was embedded in the gelatin there was little effect on the total amount of penetration, but cow skin on the front surface of the gelatin reduced penetration by about 30%.Computed tomography was used to examine the pellet track and to calculate the volume of damage produced. However, due to the similar densities of gelatin and organ a technique had to be developed to differentiate phases. A barium salt paste was applied to outer surfaces and iodine solution or barium nitrate solution containing red food colouring was injected into the pellet track to enhance the contrast of the track. The track through the gelatin tended to enclose itself whereas the track through the organ remained more open, presumably due to the inhomogeneity of the fibrous nature of the tissue.Pellets were also fired at construction materials (wood, plasterboard and brick) and computed tomography used to determine the volume of damage created. Pellets perforated single layers of wood and plasterboard and would embed in a second layer. However, if the two layers were in contact the pellet did not penetrate the first layer. An air rifle pellet could therefore perforate house construction materials, although the resultant kinetic energy would be low and further damage would be limited.Some of the possible physical parameters are discussed that might help predict the degree of damage caused, but from this study it is not possible to define a limit which could be proposed as safe
Hybrid upper surface blown flap propulsive-lift concept for the quiet short-haul research aircraft
The hybrid upper surface blowing concept consists of wing-mounted turbofan engines with a major portion of the fan exhaust directed over the wing upper surface to provide high levels of propulsive lift, but with a portion of the fan airflow directed over selected portions of the airframe to provide boundary layer control. NASA-sponsored preliminary design studies identified the hybrid upper surface blowing concept as the best propulsive lift concept to be applied to the Quiet Short-Haul Research Aircraft (QSRA) that is planned as a flight facility to conduct flight research at low noise levels high approach lift coefficients, and steep approaches. Data from NASA in-house and NASA-sponsored small and large-scale wind tunnel tests of various configurations using this concept are presented
Wind data from the 250-foot /76.2-meter/ tower at Wallops Island, Virginia
Statistical evaluation of sampled wind data from anemometers mounted on meteorological tower on Wallops Islan
Recommended from our members
Effect of Processing Parameters on the Density and Microstructure of Direct Laser Sintered Al-12Si Powders
The effect of processing parameters on the sintering behaviour of gas atomised Al-12Si
powders has been investigated. Laser power, scanning rate, scan spacing and layer
thickness are found to control the densification and the resultant microstructural
characteristics of the laser sintered parts. It was found that sintered density increased as
the energy density increased reaching a maximum of 80.2% at an energy input per unit
volume of 67 J mm-3. For parts produced with a slightly lower power density (50 J mm-3), the microstructure consisted of fine dendrites with interconnected porosity while parts
fabricated with a slightly higher power density (100 J mm-3) were noted to have a
preponderance of coarse dendrites with a discontinuous network of irregular shaped pores
surrounded by a fully dense aluminium-silicon matrix.Mechanical Engineerin
Recommended from our members
Selective Laser Sintering of Polymer Nanocomposites
This paper describes the fabrication and characterization of polymer nanocomposite (PNC)
materials for use in the selective laser sintering (SLS) process. PNC materials are of great
interest generally because of their excellent physical properties, and offer excellent potential
in rapid manufacturing of structural polymeric parts. Three different nano additive materials
have been used: cerium oxide IV, yttrium stabilized zirconia, and layered Hectorite clay.
These materials have been used to reinforce PA6 polymer using solution blending and spray
drying to create powder with particle sizes in the range of 5-40 µm. The mechanical
properties and microstructure of the PNC materials have been evaluated and the results
compared to those of unfilled polymer.Mechanical Engineerin
Cost effectiveness of a community based exercise programme in over 65 year olds: cluster randomised trial
OBJECTIVE: To assess the cost effectiveness of a community based exercise programme as a population
wide public health intervention for older adults.
DESIGN: Pragmatic, cluster randomised community intervention trial.
Setting: 12 general practices in Sheffield; four randomly selected as intervention populations, and eight as
control populations.
PARTICIPANTS: All those aged 65 and over in the least active four fifths of the population responding to a
baseline survey. There were 2283 eligible participants from intervention practices and 4137 from control
practices.
INTERVENTION: Eligible subjects were invited to free locally held exercise classes, made available for two
years.
MAIN OUTCOME MEASURES: All cause and exercise related cause specific mortality and hospital service use
at two years, and health status assessed at baseline, one, and two years using the SF-36. A cost utility
analysis was also undertaken.
RESULTS: Twenty six per cent of the eligible intervention practice population attended one or more exercise
sessions. There were no significant differences in mortality rates, survival times, or admissions. After
adjusting for baseline characteristics, patients in intervention practices had a lower decline in health status,
although this reached significance only for the energy dimension and two composite scores (p,0.05). The
incremental average QALY gain of 0.011 per person in the intervention population resulted in an
incremental cost per QALY ratio of J17 174 (95% CI =J8300 to J87 120).
CONCLUSIONS: Despite a low level of adherence to the exercise programme, there were significant gains in
health related quality of life. The programme was more cost effective than many existing medical
interventions, and would be practical for primary care commissioning agencies to implement
- …