376 research outputs found
An overview of Forward Dynamics Algorithms and their use in Open Source Dynamics Engines
Simulation of real-world dynamics is of major importance in testing and verifying developed industrial concepts and solutions, developing and verifying potential control paradigms, scientific research, learning and training tools, or the entertainment industry as a basis for a game engine. The module of the 3D virtual simulator that achieves simulation of the real-world behaviour such as rigid and elastic body dynamics, particle dynamics, fluid dynamics, electrodynamics, magnetism, etc., is often referred to as a dynamics engine or physics engine. The core of the rigid body dynamics (physics) engine is the solution to the forward dynamics problem, which is defined as finding a rigid body's path, velocity, and acceleration for a given input actuating torque and external forces. The past few decades saw a considerable amount of research in robot dynamics modelling, and there are many methods for robot dynamic model development available in the literature. The most commonly used algorithms for solving robot forward dynamics problem are the Composite-Rigid-Body Algorithm (CRBA) [1] and the Articulated-Body Algorithm (ABA) [2]. CRBA and ABA are reduced coordinate methods where known constraints, such as joints, are embedded in the formulation of the equations of motion. Besides reduced coordinate methods, there are maximal coordinate methods using Lagrange multipliers [3-4] to enforce constraints using constraint reaction forces
Recommended from our members
Flow measurement inside a zinc-nickel flow cell battery using FBG based sensor system
Downloading of the abstract is permitted for personal use only. A detailed knowledge of the internal flow distribution inside a zinc-nickel flow battery is of critical importance to ensure smooth flow of the electrolyte through the battery cell and better operation of the device. Information of this type can be used as a useful means of early detection of zinc deposition and dendrite formation inside the cell, negative factors which affect the flow and thus which can lead to internal short circuiting, this being a primary failure mode of these types of batteries. This deposition occurs at low pH levels when zinc reacts with the electrolyte to form solid zinc oxide hydroxides. Traditionally, manual inspection is conducted, but this is time consuming and costly, only providing what are often inaccurate results-overall it is an impractical solution especially with the wider use of batteries in the very near future. Fibre Bragg grating (FBG) sensors integrated inside the flow cell offer the advantage of measuring flow changes at multiple locations using a single fibre and that then can be used as an indicator of the correlation between the internal flow distribution and the deposition characteristics. This work presents an initial study, where two networks of FBGs have been installed and used for flow change detection in an active zinc-nickel flow battery. Data have been obtained from the sensor networks and information of battery performance completed and summarized in this paper. The approach shows promising results and thus scope for the future research into the development of this type of sensor system
Recommended from our members
Development of low cost packaged fibre optic sensors for use in reinforced concrete structures
There is an ongoing need to measure strains in reinforced concrete structures more reliably and under a range of circumstances e.g. long term durability (such as effects of cracking and reinforcement corrosion), response to normal working loads and response under abnormal load conditions. Fibre optic sensors have considerable potential for this purpose and have the additional advantages, including of immunity to electromagnetic interference and light weight (Grattan et al., 2000). This is important in railway scenarios and particularly so when the lines are electrified. Their small size allows for easy installation. However, their use as commercial âpackagedâ devices (traditionally seen as necessary to achieve adequate robustness) is limited by their high cost relative to other sensor devices such as encapsulated electric resistance strain gauges. This paper describes preliminary work to produce a cost-effective and easy-to-use technique for encapsulating fibre optic sensors in resin using 3D printing techniques to produce a robust, inexpensive âpackagedâ sensor system suitable for use with concrete structures. The work done to date has shown this to be a convenient and economical way of producing multiple sensors which were suitable for both surface mounting and embedment in reinforced concrete structures. The proof-of-concept testing to which the trial packages were subjected is described in the paper and the results indicate that 3D printed packages have considerable potential for further development and use in a variety of civil engineering applications, competing well with more conventional sensor systems
Recommended from our members
Optical Fibre Sensors applied to condition and structural monitoring for the marine and rail transport sectors
This thesis reports the development of a suite of FBG-based optical fibre sensors for non-destructive testing (NDT) and illustrating their potential for several specific industrial applications in the marine and railway sectors. These arose from work driven by the needs of project collaborators from these industries and are intended to be illustrative of the wider potential applications that optical fibre sensors have for measurements in different industrial sectors. The research has involved the development of new sensor system designs to meet these needs, building as they do upon a comprehensive review of NDT technologies and solutions, discussed in some detail.
In this research for the marine sector, a single FBG-based acoustic sensor was specifically developed and evaluated and compared with the performance of conventional sensors. To do so, a metal plate to which the sensors were fixed was excited with a sonotrode, at a resonant frequency of 19.5 kHz. The signal reflecting that acoustic excitation was captured by the FBG sensors designed and implemented and their performance has been shown to be comparable with that from conventional, industry-standard piezoelectric transducers (PZTs). Preliminary work undertaken for the sponsors then lead to the further development of an acoustic sensor array comprising of 3 FBGs, which was subsequently validated against co-located PZTs which all were installed on a glass plate and excited in an industry-standard way, through the acoustic signal from a 0.2 g steel ball dropped onto the plate. When signals were analysed and compared, the positive comparative performance outcomes from the sensors used enabled further the design and implementation of instrumentation for a marine lifting surface using a different array, designed comprising 4 FBG-based acoustic sensors. Extensive tests on the smart marine lifting surface created were undertaken under water with a sonotrode set at 26 kHz as an excitation source. Based on the arrival time of acoustic signals captured by each grating and the use of triangulation method, the location of the excitation source could thus be determined, to meet the needs of the industrial sponsor and show good agreement with the outputs of conventional sensor systems.
In parallel with the above, a further new industrial application of FBG-based sensor arrays was developed for a major player in the field, for the first time successfully instrumenting a railway current-collecting pantograph to allow reliable, remote in situ monitoring of key parameters: the contact force and contact location of the pantograph against the catenary. The optical fibre sensor approach has been shown to be an excellent means of measurement whose performance can be extrapolated to situations where the train is driven at high speeds up to 125 mph and powered from a high voltage line at 25 kV, in this design taking full advantages of the immunity of the optical fibre sensors to electromagnetic interference. In this research, key technical performance challenges were addressed and successfully overcome, including the temperature compensation needed for âall-weatherâ performance, due to the intrinsic cross-sensitivity problems of using a FBG-based design being been fully addressed. This ensures the accurate measurement of the contact force/location between the pantograph and the catenary under all weathers.
The research concludes by considering future directions for the work in these and other industry sectors
Impact of Short-Term Variations in the Generation Output of Geographically Dispersed PV Systems
When viewed in hourly intervals, a solar photovoltaic (PV) system appears to have a more stable output than usual. However, there are short-term rapid variations in its generation output that result from transient cloudiness and weather disturbances in the atmosphere. By using Monte Carlo simulations applied to a Markov model, this study demonstrates the short-term intermittency of the transient weather conditions and estimates the generation of geographically dispersed PV systems with a capacity of ten percent of peak demand of a statewide grid in one-minute intervals. This study found that geographically distributed PV systems evaluated in one-minute intervals could cope with peaks of a statewide power grid because of the smoothing effect caused by the geographical spread. The purpose of the exercise is to create a framework for integration and optimization of multiple generation sources in order to meet the uncertainty of the fast changing PV output under certain weather conditions.
Performance of the WaveBurst algorithm on LIGO data
In this paper we describe the performance of the WaveBurst algorithm which
was designed for detection of gravitational wave bursts in interferometric
data. The performance of the algorithm was evaluated on the test data set
collected during the second LIGO Scientific run. We have measured the false
alarm rate of the algorithm as a function of the threshold and estimated its
detection efficiency for simulated burst waveforms.Comment: proceedings of GWDAW, 2003 conference, 13 pages, 6 figure
Recommended from our members
Fibre Bragg Grating-based Acoustic Sensor Array for Improved Condition Monitoring of Marine Lifting Surfaces
This paper discusses a novel approach to monitor marine lifting surface conditions through using arrays of Fibre Bragg Grating (FBG)-based acoustic sensors in a marine rudder. Results from these optical sensor arrays are then cross compared with those from conventional piezoelectric (PZT) sensors. A successful proof-of-concept evaluation of the optical sensor approach was, however, first undertaken by using cascaded FBGs integrated into a glass plate, monitoring the response to dropping a standard metal ball at different locations. Data obtained were compared with colocated conventional PZT sensors acoustic sensors for comparison using triangulation to determine the location of the excitation source (a sonotrode). The results obtained verify the excellent performance of the FBG-based sensors due to the excellent agreement between these different sensor types. This gives confidence to the next-stage to scale-up the FBG sensor arrays for other marine structures, with early identification of the initiation of cavitation erosion an important priority for better operational reliability and scheduling of maintenance of marine vessels
Recommended from our members
A temperature compensated fibre Bragg grating (FBG)-based sensor system for condition monitoring of electrified railway pantograph
This paper presents the results obtained from fibre Bragg grating (FBG) sensors integrated into a railway current-collecting pantograph for accurate measurement of contact force and contact location when it is infjected to various temperature conditions. The temperature change of the pantograph is simulated, at the industrial laboratory of Brecknell Willis in the UK, by changing the DC current applied to pantograph from 0 to 1500 A. This test is primarily designed to verify the effectiveness of the temperature compensation mechanism built in the FBG sensor design. For this verification, 3 thermocouples co-located with the FBG sensor packages are used to measure the temperature change seen from 25 °C to 55 °C. The tests were repeated several times and the sensor system has shown its temperatureindependence, confirming that the intrinsic cross-sensitivity of FBGs to temperature variation for strain measurement has been fully compensated through the use of this innovative sensor design and data processing
Recommended from our members
Graphene oxide coated long period grating for optical sensing purposes
In this paper, fabrication and surrounding refractive index response of a graphene oxide (GO) coated long period grating (LPG) is presented. An improved version of the Hummer's method was followed for the synthesis of GO used in this work and GO sheets were immobilized on the LPG fibre surface by using an electrostatic self-assembly technique. In this initial performance evaluation, intensity and wavelength variations of the transmission loss bands of the GO coated LPG were recorded at room temperature and this sensor probe is introduced as a good candidate for the further development of selective biosensors
- âŠ