Bedrock geology of DFDP-2B, central Alpine Fault, New Zealand

<p>During the second phase of the Alpine Fault, Deep Fault Drilling Project (DFDP) in the Whataroa River, South Westland, New Zealand, bedrock was encountered in the DFDP-2B borehole from 238.5–893.2 m Measured Depth (MD). Continuous sampling and meso- to microscale characterisation of whole rock cuttings established that, in sequence, the borehole sampled amphibolite facies, Torlesse Composite Terrane-derived schists, protomylonites and mylonites, terminating 200–400 m above an Alpine Fault Principal Slip Zone (PSZ) with a maximum dip of 62°. The most diagnostic structural features of increasing PSZ proximity were the occurrence of shear bands and reduction in mean quartz grain sizes. A change in composition to greater mica:quartz + feldspar, most markedly below c. 700 m MD, is inferred to result from either heterogeneous sampling or a change in lithology related to alteration. Major oxide variations suggest the fault-proximal Alpine Fault alteration zone, as previously defined in DFDP-1 core, was not sampled.</p

Petrophysical, Geochemical, and Hydrological Evidence for Extensive Fracture-Mediated Fluid and Heat Transport in the Alpine Fault's Hanging-Wall Damage Zone

International audienceFault rock assemblages reflect interaction between deformation, stress, temperature, fluid, and chemical regimes on distinct spatial and temporal scales at various positions in the crust. Here we interpret measurements made in the hanging‐wall of the Alpine Fault during the second stage of the Deep Fault Drilling Project (DFDP‐2). We present observational evidence for extensive fracturing and high hanging‐wall hydraulic conductivity (∼10−9 to 10−7 m/s, corresponding to permeability of ∼10−16 to 10−14 m2) extending several hundred meters from the fault's principal slip zone. Mud losses, gas chemistry anomalies, and petrophysical data indicate that a subset of fractures intersected by the borehole are capable of transmitting fluid volumes of several cubic meters on time scales of hours. DFDP‐2 observations and other data suggest that this hydrogeologically active portion of the fault zone in the hanging‐wall is several kilometers wide in the uppermost crust. This finding is consistent with numerical models of earthquake rupture and off‐fault damage. We conclude that the mechanically and hydrogeologically active part of the Alpine Fault is a more dynamic and extensive feature than commonly described in models based on exhumed faults. We propose that the hydrogeologically active damage zone of the Alpine Fault and other large active faults in areas of high topographic relief can be subdivided into an inner zone in which damage is controlled principally by earthquake rupture processes and an outer zone in which damage reflects coseismic shaking, strain accumulation and release on interseismic timescales, and inherited fracturing related to exhumation

High resolution muscle measurements provide insights into equinus contractures in patients with cerebral palsy.

Muscle contractures that occur after upper motor neuron lesion are often surgically released or lengthened. However, surgical manipulation of muscle length changes a muscle's sarcomere length (Ls ), which can affect force production. To predict effects of surgery, both macro- (fascicle length (Lf )) and micro- (Ls ) level structural measurements are needed. Therefore, the purpose of this study was to quantify both Ls and Lf in patients with cerebral palsy (CP) as well as typically developing (TD) children. Soleus ultrasound images were obtained from children with CP and TD children. Lf was determined and, with the joint in the same position, CP biopsies were obtained and formalin fixed, and Ls was measured by laser diffraction. Since soleus Ls values were not measurable in TD children, TD Ls values were obtained using three independent methods. While average Lf did not differ between groups (CP=3.6±1.2 cm, TD=3.5±0.9 cm; p&gt;0.6), Ls was dramatically longer in children with CP (4.07±0.45 µm vs. TD=2.17±0.24 µm; p&lt;0.0001). While Lf values were similar between children with CP and TD children, this was due to highly stretched sarcomeres within the soleus muscle. Surgical manipulation of muscle-tendon unit length will thus alter muscle sarcomere length and change force generating capacity of the muscle

Extreme hydrothermal conditions at an active plate-bounding fault

Temperature and fluid pressure conditions control rock deformation and mineralization on geological faults, and hence the distribution of earthquakes. Typical intraplate continental crust has hydrostatic fluid pressure and a near-surface thermal gradient of 31 ± 15 degrees Celsius per kilometre. At temperatures above 300-450 degrees Celsius, usually found at depths greater than 10-15 kilometres, the intra-crystalline plasticity of quartz and feldspar relieves stress by aseismic creep and earthquakes are infrequent. Hydrothermal conditions control the stability of mineral phases and hence frictional-mechanical processes associated with earthquake rupture cycles, but there are few temperature and fluid pressure data from active plate-bounding faults. Here we report results from a borehole drilled into the upper part of the Alpine Fault, which is late in its cycle of stress accumulation and expected to rupture in a magnitude 8 earthquake in the coming decades. The borehole (depth 893 metres) revealed a pore fluid pressure gradient exceeding 9 ± 1 per cent above hydrostatic levels and an average geothermal gradient of 125 ± 55 degrees Celsius per kilometre within the hanging wall of the fault. These extreme hydrothermal conditions result from rapid fault movement, which transports rock and heat from depth, and topographically driven fluid movement that concentrates heat into valleys. Shear heating may occur within the fault but is not required to explain our observations. Our data and models show that highly anomalous fluid pressure and temperature gradients in the upper part of the seismogenic zone can be created by positive feedbacks between processes of fault slip, rock fracturing and alteration, and landscape development at plate-bounding faults

A physical map of the bovine genome

A new physical map of the bovine genome has been constructed by integrating data from genetic and radiation hybrid maps, and a new bovine BAC map, with the bovine genome draft assembly

Supplementary Data to: &ldquo;Bedrock Geology of DFDP-2B, Central Alpine Fault, New Zealand&quot;

These data are supplementary material to &ldquo;Bedrock Geology of DFDP-2B, Central Alpine Fault, New Zealand&rdquo; (Toy et al., 2017, http://doi.org/10.1080/00288306.2017.1375533). The data tables SF3 and SF4 are provided as well as Excel as well as CSV and PDF versions (in the zip folder). The table numbers below are referring to Toy et al. (2017): Toy_SF1.pdf (Data Description): Supplementary Data to &ldquo;Bedrock Geology of DFDP-2B, Central Alpine Fault, New Zealand&rdquo;, including supplementary methods, Information on reference frames and corrections, and protocols for thin section preparation and scanning electron microscopic analyses. Toy_SF2: Table S1. Time vs. depth during drilling, with lag dip corrections Toy_SF3: Table S2. Energy dispersive spectroscopy (EDS) data acquired using a TESCAN Integrated Mineral Analyzer (TIMA) and phases detected by mineral liberation analysis (MLA) Toy_SF4: Table S3. Electron backscatter diffraction (EBSD) grain sizes.</span