Design and commissioning of a virtual image solar simulator for testing thermal collectors

A solar simulator has been designed and built for testing prototype (0.5×0.5 m) flat plate thermal collectors. An internally reflecting light tube generates multiple virtual images of the four halogen floodlights to ensure uniform illumination. Ray-tracing simulations were used to choose the tube dimensions and maximum allowable clearance. Illumination measurements agree well with these predictions. The visible & near IR spectrum appears to follow a black body curve. In the absence of a “cold sky” IR filter there is a secondary, long wavelength IR spectral component that causes heating of the cover glass on a solar flat plate collector. The cover glass temperature can be maintained at typical outdoor levels using a cooling fan. The design would be well suited to LED illumination. Simulation of solar collector response to this spectrum shows that an efficiency based on pyranometer readings is approximately 1% higher than would be obtained with an AM1.5 spectrum

Simulator testing of evacuated flat plate solar collectors for industrial heat and building integration

The concept of an evacuated flat plate collector was proposed over 40 years ago but, despite its professed advantages, very few manufacturers have developed commercial versions. This paper demonstrates the reduction in heat loss coefficient and increase in efficiency resulting from evacuating a flat plate collector: it is hoped that these results will stimulate interest in the concept. Evacuated tubes are now mass-produced in large numbers; evacuated flat plate collectors could in principle replace these tubes if the technical difficulties in creating extended metal-glass seals can be overcome. The experimental experiences described here should indicate targets for future research. Two different designs of evacuated flat plate solar thermal collector, each with a 0.5x0.5m flooded panel black chrome plated absorber, were tested under a solar simulator. The cover glasses were supported by an array of 6 mm diameter pillars. Inlet and outlet temperatures were monitored via PT100 RTDs and glass temperatures were measured using thermocouples. Inlet temperature was controlled by a fluid circulator connected to a header tank with a Coriolis mass flow meter to measure fluid flow rate. Testing was conducted indoors with and without the use of a fan to cool the top cover glass. The test conditions spanned the range 200<G<1000 W/m², 0 less than or equal to TM/G less than or equal to 52°C. Evacuating the enclosure reduced the measured heat loss coefficient by 3.7 W/m²K: this was a close match to predictions and corresponds to an increase in aperture efficiency from 0.3 to 0.6 at TM/G = 0.06 m2K/W. The poor efficiency under non-evacuated conditions was due to the black chrome absorber coating being less selective than commercial panel coatings. The solder seals were developed from experience with vacuum glazing but the increased gap led to reliability issues. A vacuum pump maintained the enclosures under a high vacuum (<0.1 Pa) during testing. The enclosure based on a thin rear metal tray proved to be more effectively sealed than the more rigid enclosure with glass on both sides: the latter developed leaks as the front to rear temperature difference increased. The biggest challenge in the manufacture of evacuated flat plate collectors is to ensure a long-term hermetic seal such that no pumping is required

Producing Policy-relevant Science by Enhancing Robustness and Model Integration for the Assessment of Global Environmental Change

We use the flexible model coupling technology known as the bespoke framework generator to link established existing modules representing dynamics in the global economy (GEMINI_E3), the energy system (TIAM-WORLD), the global and regional climate system (MAGICC6, PLASIM-ENTS and ClimGEN), the agricultural system, the hydrological system and ecosystems (LPJmL), together in a single integrated assessment modelling (IAM) framework, building on the pre-existing framework of the Community Integrated Assessment System. Next, we demonstrate the application of the framework to produce policy-relevant scientific information. We use it to show that when using carbon price mechanisms to induce a transition from a high-carbon to a low-carbon economy, prices can be minimised if policy action is taken early, if burden sharing regimes are used, and if agriculture is intensified. Some of the coupled models have been made available for use at a secure and user-friendly web portal. © 2018 The Author

Tensor Correlations Measured in 3He(e,e'pp)n

We have measured the 3He(e,e'pp)n reaction at an incident energy of 4.7 GeV over a wide kinematic range. We identified spectator correlated pp and pn nucleon pairs using kinematic cuts and measured their relative and total momentum distributions. This is the first measurement of the ratio of pp to pn pairs as a function of pair total momentum, $p_{tot}$. For pair relative momenta between 0.3 and 0.5 GeV/c, the ratio is very small at low $p_{tot}$ and rises to approximately 0.5 at large $p_{tot}$. This shows the dominance of tensor over central correlations at this relative momentum.Comment: 4 pages, 4 figures, submitted to PR

Measurement of the nuclear multiplicity ratio for Ks0K^0_s hadronization at CLAS

The influence of cold nuclear matter on lepto-production of hadrons in semi-inclusive deep inelastic scattering is measured using the CLAS detector in Hall B at Jefferson Lab and a 5.014 GeV electron beam. We report the $K_s^0$ multiplicity ratios for targets of C, Fe, and Pb relative to deuterium as a function of the fractional virtual photon energy $z$ transferred to the $K_s^0$ and the transverse momentum squared $p_{T}^2$ of the $K_s^0$. We find that the multiplicity ratios for $K^0_s$ are reduced in the nuclear medium at high $z$ and low $p_{T}^2$, with a trend for the $K^0_s$ transverse momentum to be broadened in the nucleus for large $p_{T}^2$.Comment: Submitted to Phys. Lett.

Coherent Photoproduction of pi^+ from 3^He

We have measured the differential cross section for the $\gamma$$^3$He$\rightarrow \pi^+ t$ reaction. This reaction was studied using the CEBAF Large Acceptance Spectrometer (CLAS) at Jefferson Lab. Real photons produced with the Hall-B bremsstrahlung tagging system in the energy range from 0.50 to 1.55 GeV were incident on a cryogenic liquid $^3$He target. The differential cross sections for the $\gamma$$^3$He$\rightarrow \pi^+ t$ reaction were measured as a function of photon-beam energy and pion-scattering angle. Theoretical predictions to date cannot explain the large cross sections except at backward angles, showing that additional components must be added to the model.Comment: 11 pages, 16 figure

Performance and operational effectiveness of evacuated flat plate solar collectors compared with conventional thermal, PVT and PV panels

The concept of an evacuated flat plate (EFP) collector was proposed over 40 years ago but, despite its professed advantages, very few manufacturers have developed commercial versions. This situation suggests both technical difficulties in manufacturing a competitively-priced sealed for life panel and a lack of awareness of the bene fits of such panels. This paper demonstrates an evacuated flat plate simulation that closely models experimental efficiency measurements. Having established the validity of the model, it compares published data for a commercial EFP collector with predictions for an optimal design to investigate whether any further efficiency improvement might be possible. The optimised design is then evaluated against alternative solar energy devices by modelling a number of possible applications. These comparisons should inform choices about solar options for delivering heat: EFP collectors are well-suited to some of these applications. Evacuated flat plate collectors are a possible alternative to concentrating collectors for Organic Rankine Cycle power generation. The annual output for all the modelled collectors was found to be a quadratic function of delivery temperature: this enabled a novel optimisation of ORC source temperature. Predictions for concentrating and non-concentrating ORC plant are compared with a PV/thermal alternative. The ORC output is significantly less than a PV panel would achieve; applications needing both heat and power are better served by PVT panels. This is an original and novel result

Virtual Compton Scattering and Neutral Pion Electroproduction in the Resonance Region up to the Deep Inelastic Region at Backward Angles

We have made the first measurements of the virtual Compton scattering (VCS) process via the H$(e,e'p)\gamma$ exclusive reaction in the nucleon resonance region, at backward angles. Results are presented for the $W$-dependence at fixed $Q^2=1$ GeV$^2$, and for the $Q^2$-dependence at fixed $W$ near 1.5 GeV. The VCS data show resonant structures in the first and second resonance regions. The observed $Q^2$-dependence is smooth. The measured ratio of H$(e,e'p)\gamma$ to H$(e,e'p)\pi^0$ cross sections emphasizes the different sensitivity of these two reactions to the various nucleon resonances. Finally, when compared to Real Compton Scattering (RCS) at high energy and large angles, our VCS data at the highest $W$ (1.8-1.9 GeV) show a striking $Q^2$- independence, which may suggest a transition to a perturbative scattering mechanism at the quark level.Comment: 20 pages, 8 figures. To appear in Phys.Rev.

Demonstration of a novel technique to measure two-photon exchange effects in elastic e±pe^\pm p scattering

The discrepancy between proton electromagnetic form factors extracted using unpolarized and polarized scattering data is believed to be a consequence of two-photon exchange (TPE) effects. However, the calculations of TPE corrections have significant model dependence, and there is limited direct experimental evidence for such corrections. We present the results of a new experimental technique for making direct $e^\pm p$ comparisons, which has the potential to make precise measurements over a broad range in $Q^2$ and scattering angles. We use the Jefferson Lab electron beam and the Hall B photon tagger to generate a clean but untagged photon beam. The photon beam impinges on a converter foil to generate a mixed beam of electrons, positrons, and photons. A chicane is used to separate and recombine the electron and positron beams while the photon beam is stopped by a photon blocker. This provides a combined electron and positron beam, with energies from 0.5 to 3.2 GeV, which impinges on a liquid hydrogen target. The large acceptance CLAS detector is used to identify and reconstruct elastic scattering events, determining both the initial lepton energy and the sign of the scattered lepton. The data were collected in two days with a primary electron beam energy of only 3.3 GeV, limiting the data from this run to smaller values of $Q^2$ and scattering angle. Nonetheless, this measurement yields a data sample for $e^\pm p$ with statistics comparable to those of the best previous measurements. We have shown that we can cleanly identify elastic scattering events and correct for the difference in acceptance for electron and positron scattering. The final ratio of positron to electron scattering: $R=1.027\pm0.005\pm0.05$ for $=0.206$ GeV$^2$ and $0.830\leq \epsilon\leq 0.943$

Precise Measurements of Beam Spin Asymmetries in Semi-Inclusive π0\pi^0 production

We present studies of single-spin asymmetries for neutral pion electroproduction in semi-inclusive deep-inelastic scattering of 5.776 GeV polarized electrons from an unpolarized hydrogen target, using the CEBAF Large Acceptance Spectrometer (CLAS) at the Thomas Jefferson National Accelerator Facility. A substantial $\sin \phi_h$ amplitude has been measured in the distribution of the cross section asymmetry as a function of the azimuthal angle $\phi_h$ of the produced neutral pion. The dependence of this amplitude on Bjorken $x$ and on the pion transverse momentum is extracted with significantly higher precision than previous data and is compared to model calculations.Comment: to be submitted PL