Complexation of lithium and sodium cations with B-phosphorylate ethers, modelling terminal groups of organophosphorus podands. An experimental and theoretical study

The organophosphorus compounds o-Ph2P(O)C6H4OCH3 and Ph2P(O)C2H4OCH3, which are analogs of podands' terminal groups, have been synthesized. The thermodynamic characteristics of their complexation with LiNCS and NaNCS in acetonitrile were obtained by calorimetry. Molecular mechanics calculations on M+ L complexes with different stoichiometries M+:L = 1:1, 1:2 and 1:4 (M+ = Li+, Na+) were performed, as well as on their solvates with a limited number of MeCN molecules. It has been shown that the experimental data could be explained by taking into account both the specific features of the complex structure and the solvent effects. The possibility of the application of additive schemes in the investigation of the complexation of polydentate molecules is discussed

Polarization-resolved strong light–matter coupling in planar GaAs/AlGaAs waveguides

We study the influence of optical selection rules and polarization splittings on properties of exciton polaritons in a planar AlGaAs waveguide containing embedded GaAs quantum wells. We demonstrate that transverse electric and transverse magnetic modes couple differently with light- and heavy-hole quantum well excitons, which leads to distinct polarization splittings of the resulting polariton modes. The experimental data are in good agreement with modeling based on theoretical data for the optical selection rules for quantum well excitons

Rolled-Up Nanotech: Illumination-Controlled Hydrofluoric Acid Etching of AlAs Sacrificial Layers

<p>Abstract</p> <p>The effect of illumination on the hydrofluoric acid etching of AlAs sacrificial layers with systematically varied thicknesses in order to release and roll up InGaAs/GaAs bilayers was studied. For thicknesses of AlAs below 10 nm, there were two etching regimes for the area under illumination: one at low illumination intensities, in which the etching and releasing proceeds as expected and one at higher intensities in which the etching and any releasing are completely suppressed. The &#8220;etch suppression&#8221; area is well defined by the illumination spot, a feature that can be used to create heterogeneously etched regions with a high degree of control, shown here on patterned samples. Together with the studied self-limitation effect, the technique offers a way to determine the position of rolled-up micro- and nanotubes independently from the predefined lithographic pattern.</p

Study of the lineshape of the chi(c1) (3872) state

A study of the lineshape of the chi(c1) (3872) state is made using a data sample corresponding to an integrated luminosity of 3 fb(-1) collected in pp collisions at center-of-mass energies of 7 and 8 TeV with the LHCb detector. Candidate chi(c1)(3872) and psi(2S) mesons from b-hadron decays are selected in the J/psi pi(+)pi(-) decay mode. Describing the lineshape with a Breit-Wigner function, the mass splitting between the chi(c1 )(3872) and psi(2S) states, Delta m, and the width of the chi(c1 )(3872) state, Gamma(Bw), are determined to be (Delta m=185.598 +/- 0.067 +/- 0.068 Mev,)(Gamma BW=1.39 +/- 0.24 +/- 0.10 Mev,) where the first uncertainty is statistical and the second systematic. Using a Flatte-inspired model, the mode and full width at half maximum of the lineshape are determined to be (mode=3871.69+0.00+0.05 MeV.)(FWHM=0.22-0.04+0.13+0.07+0.11-0.06-0.13 MeV, ) An investigation of the analytic structure of the Flatte amplitude reveals a pole structure, which is compatible with a quasibound D-0(D) over bar*(0) state but a quasivirtual state is still allowed at the level of 2 standard deviations

Helium identification with LHCb

The identification of helium nuclei at LHCb is achieved using a method based on measurements of ionisation losses in the silicon sensors and timing measurements in the Outer Tracker drift tubes. The background from photon conversions is reduced using the RICH detectors and an isolation requirement. The method is developed using pp collision data at √(s) = 13 TeV recorded by the LHCb experiment in the years 2016 to 2018, corresponding to an integrated luminosity of 5.5 fb-1. A total of around 105 helium and antihelium candidates are identified with negligible background contamination. The helium identification efficiency is estimated to be approximately 50% with a corresponding background rejection rate of up to O(10^12). These results demonstrate the feasibility of a rich programme of measurements of QCD and astrophysics interest involving light nuclei

CFD simulation of the ethylbenzene dehydrogenation reaction in the fixed bed reactor with a cylindrical catalyst of various sizes

In this paper, the Discrete Element Method of simulation was used to study the catalytic granule size effect on the efficiency of a bed reactor for the ethylbenzene dehydrogenation reaction. The model constructed for the laboratory experiment was made of catalyst granules of lengths 3, 6 and 9 mm, and diameters 2.8, 3, and 3.2 mm. A detailed evaluation of the catalyst total surface area and porosity effect was conducted owing to the analysis of particles size effect on the packing. Different results were observed for a wide feed gas mixture rate. Calculations performed allowed to deduce dependences of the reaction product concentration, the pressure drops, and the reactor productivity for all the particle sizes investigated

Mathematical simulation of the reactor for the ethylbenzene to styrene dehydrogenation reaction

© Published under licence by IOP Publishing Ltd. In this work, we carried out a numerical simulation of an industrial reactor of a radial type with a fixed catalyst bed for the process of ethylbenzene to styrene dehydrogenation. We solved the problem in the approximation of two-dimensional axial symmetry. The parameters of the chemically reacting gas mixture movement in the catalyst bed are considered. The reactor zones which have a negative impact on the reaction efficiency have been determined

Rolled-up magnetic microdrillers: Towards remotely controlled minimally invasive surgery

Self-folded magnetic microtools with sharp ends are directed at enabling drilling and related incision operations of tissues, ex vivo, in a fluid with a viscosity similar to that of blood. These microtools change their rotation from a horizontal to a vertical one when they are immersed into a rotational magnetic field. Novel self-assembly paradigms with magnetic materials can enable the creation of remotely controlled and mass-produced tools for potential applications in minimally invasive surgery