Low power low voltage quadrature RC oscillators for modern RF receivers

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de ComputadoresThis thesis proposes a study of three different RC oscillators, two relaxation and a ring oscillator. All the circuits are implemented using UMC 130 nm CMOS technology with a supply voltage of 1.2 V. We present a wideband MOS current/voltage controlled quadrature oscillator constituted by two multivibrators. Two different forms of coupling named, soft (traditional)and hard (proposed) are differentiated and investigated. It is found that hard coupling reduces the quadrature error and results in a low phase-noise (about 2 dB improvement) with respect to soft coupling. The behaviour of the singular and coupled multivibrators is investigated, when an external synchronizing harmonic is applied. We introduce a new RC relaxation oscillator with pulse self biasing, to reduce power consumption, and with harmonic ltering and resistor feedback, to reduce phase-noise. The designed circuit has a very low phase-noise, -132.6 dBc/Hz @ 10 MHz offset, and the power consumption is only 1 mW, which leads to a gure of merit (FOM) of -159.1 dBc/Hz. The nal circuit is a two integrator fully implemented in CMOS technology, with low power consumption. The respective layout is made and occupies a total area of5.856x10-3 mm2, post-layout simulation is also done

Integrated reference circuits for low-power capacitive sensor interfaces

This thesis consists of nine publications and an overview of the research topic, which also summarizes the work. The research described in this thesis concentrates on the design of low-power sensor interfaces for capacitive 3-axis micro-accelerometers. The primary goal throughout the thesis is to optimize power dissipation. Because the author made the main contribution to the design of the reference and power management circuits required, the overview part is dominated by the following research topics: current, voltage, and temperature references, frequency references, and voltage regulators. After an introduction to capacitive micro-accelerometers, the work describes the typical integrated readout electronics of a capacitive sensor on the functional level. The readout electronics can be divided into four different functional parts, namely the sensor readout itself, signal post-processing, references, and power management. Before the focus is shifted to the references and further to power management, different ways to realize the sensor readout are briefly discussed. Both current and voltage references are required in most analog and mixed-signal systems. A bandgap voltage reference, which inherently uses at least one current reference, is practical for the generation of an accurate reference voltage. Very similar circuit techniques can be exploited when implementing a temperature reference, the need for which in the sensor readout may be justified by the temperature compensation, for example. The work introduces non-linear frequency references, namely ring and relaxation oscillators, which are very suitable for the generation of the relatively low-frequency clock signals typically needed in the sensor interfaces. Such oscillators suffer from poor jitter and phase noise performance, the quantities of which also deserve discussion in this thesis. Finally, the regulation of the supply voltage using linear regulators is considered. In addition to extending the battery life by providing a low quiescent current, the regulator must be able to supply very low load currents and operate without off-chip capacitors

A low power, low noise, 1.8 GHz voltage-controlled oscillator

Thesis (M.S.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 1997.Includes bibliographical references (leaf 97).by Donald A. Hitko.M.S

Основи схемотехніки електронних систем

Basics of circuitry are stated, principles of operation are considered, it is given calculations of analog, digital and pulse devices of electronic systems, based on semiconductor devices, integrated operational amplifiers and integrated logic circuits of TTL, MOS, CMOS types, construction principles of systems of control by electronics devices based on microprocessors and microcontrollers. For students of institutions of higher education. It can be useful for specialists on electronic engineering, specializing in the area of development, fabrication and maintenance of electronic systems and devices

Design of a Digital Temperature Sensor based on Thermal Diffusivity in a Nanoscale CMOS Technology

Temperature sensors are widely used in microprocessors to monitor on-chip temperature gradients and hot-spots, which are known to negatively impact reliability. Such sensors should be small to facilitate floor planning, fast to track millisecond thermal transients, and easy to trim to reduce the associated costs. Recently, it has been shown that thermal diffusivity (TD) sensors can meet these requirements. These sensors operate by digitalizing the temperature-dependent delay associated with the diffusion of heat pulses through an electro-thermal filter (ETF), which, in standard CMOS, can be readily implemented as a resistive heater surrounded by a thermopile. Unlike BJT-based temperature sensors, their accuracy actually improves with CMOS scaling, since it is mainly limited by the accuracy of the heather/thermopile spacing. In this work is presented the electrical design of an highly digital TD sensor in 0.13 µm CMOS with an accuracy better than 1 ºC resolution at with 1 kS/s sampling rate, and which compares favourably to state-of-the-art sensors with similar accuracy and sampling rates [1][2][3][4]. This advance is mainly enabled by the adoption of a highly digital CCO-based phasedomain ΔΣ ADC. The TD sensor presented consists of an ETF, a transconductance stage, a current-controlled oscillator (CCO) and a 6 bit digital counter. In order to be easily ported to nanoscale CMOS technologies, it is proposed to use a sigmadelta modulator based on a CCO as an alternative to traditional modulators. And since 70% of the sensor’s area is occupied by digital circuitry, porting the sensor to latest CMOS technologies process should reduce substantially the occupied die area, and thus reduce significantly the total sensor area

Integrated RF oscillators and LO signal generation circuits

This thesis deals with fully integrated LC oscillators and local oscillator (LO) signal generation circuits. In communication systems a good-quality LO signal for up- and down-conversion in transmitters is needed. The LO signal needs to span the required frequency range and have good frequency stability and low phase noise. Furthermore, most modern systems require accurate quadrature (IQ) LO signals. This thesis tackles these challenges by presenting a detailed study of LC oscillators, monolithic elements for good-quality LC resonators, and circuits for IQ-signal generation and for frequency conversion, as well as many experimental circuits. Monolithic coils and variable capacitors are essential, and this thesis deals with good structures of these devices and their proper modeling. As experimental test devices, over forty monolithic inductors and thirty varactors have been implemented, measured and modeled. Actively synthesized reactive elements were studied as replacements for these passive devices. At first glance these circuits show promising characteristics, but closer noise and nonlinearity analysis reveals that these circuits suffer from high noise levels and a small dynamic range. Nine circuit implementations with various actively synthesized variable capacitors were done. Quadrature signal generation can be performed with three different methods, and these are analyzed in the thesis. Frequency conversion circuits are used for alleviating coupling problems or to expand the number of frequency bands covered. The thesis includes an analysis of single-sideband mixing, frequency dividers, and frequency multipliers, which are used to perform the four basic arithmetical operations for the frequency tone. Two design cases are presented. The first one is a single-sideband mixing method for the generation of WiMedia UWB LO-signals, and the second one is a frequency conversion unit for a digital period synthesizer. The last part of the thesis presents five research projects. In the first one a temperature-compensated GaAs MESFET VCO was developed. The second one deals with circuit and device development for an experimental-level BiCMOS process. A cable-modem RF tuner IC using a SiGe process was developed in the third project, and a CMOS flip-chip VCO module in the fourth one. Finally, two frequency synthesizers for UWB radios are presented

Ranger tv subsystem /block iii/. volume 3- tv subsystem design final report, jul. 1961 - jul. 1965

Ranger television subsystem desig

The teaching of electronics in schools and further education: a case study in curriculum change.

This case study describes the development of Electronics within the curriculum in line with how both (Reid and Walker I975, Case Studies in Curriculum Change) and (Goodson I983, School Subjects and Curriculum Change) discussed changes in terms of theories of curriculum change. Alternative definitions of the term innovation are reviewed and for the purpose of this study a definition is adopted which includes syllabus change and major changes of scale and strategy. The study gives an outline of the major theories of innovation and implementation strategy. Features of centralisation and rationalisation are described insofar as these features led to current educational initiatives. An account Is given of how Electronics developed as a topic within ‘A’ level Physics, a subject within B.E.T.E.C. (previously O.N.C/T.E.C.) and as a separate G.C.E. subject. Data on examination entries In G.C.E. and C.S.E. Electronics are presented. These data are related to the- size of L.E.A.s, the type of centre, and also to explore the viability of G.C.E./G.C.S.E. provision in Electronics. Initiatives such as M.E.P., T.V.E.I., C.P.V.E., S.S.C.R. are described as they are expected to have a significant impact on the growth of Electronics. The position of Electronics within the curriculum and its educational value are discussed. Comment is made on the Systems and Components approaches to Electronics and on the importance of project work. Teacher difficulties with project work are noted and suggestions are made on the use and range of equipment available so that a suitable teaching style may be -developed