Ultra thin ultrafine-pitch chip-package interconnections for embedded chip last approach

Ever growing demands for portability and functionality have always governed the electronic technology innovations. IC downscaling with Moore s law and system miniaturization with System-On-Package (SOP) paradigm has resulted and will continue to result in ultraminiaturized systems with unprecedented functionality at reduced cost. The trend towards 3D silicon system integration is expected to downscale IC I/O pad pitches from 40µm to 1- 5 µm in future. Device- to- system board interconnections are typically accomplished today with either wire bonding or solders. Both of these are incremental and run into either electrical or mechanical barriers as they are extended to higher density of interconnections. Alternate interconnection approaches such as compliant interconnects typically require lengthy connections and are therefore limited in terms of electrical properties, although expected to meet the mechanical requirements. As supply currents will increase upto 220 A by 2012, the current density will exceed the maximum allowable current density of solders. The intrinsic delay and electromigration in solders are other daunting issues that become critical at nanometer size technology nodes. In addition, formation of intermetallics is also a bottleneck that poses significant mechanical issues. Recently, many research groups have investigated various techniques for copper-copper direct bonding. Typically, bonding is carried out at 400oC for 30 min followed by annealing for 30 min. High thermal budget in such process makes it less attractive for integrated systems because of the associated process incompatibilities. In the present study, copper-copper bonding at ultra fine-pitch using advanced nano-conductive and non-conductive adhesives is evaluated. The proposed copper-copper based interconnects using advanced conductive and non-conductive adhesives will be a new fundamental and comprehensive paradigm to solve all the four barriers: 1) I/O pitch 2) Electrical performance 3) Reliability and 4) Cost. This thesis investigates the mechanical integrity and reliability of copper-copper bonding using advanced adhesives through test vehicle fabrication and reliability testing. Test vehicles were fabricated using low cost electro-deposition techniques and assembled onto glass carrier. Experimental results show that proposed copper-copper bonding using advanced adhesives could potentially meet all the system performance requirements for the emerging micro/nano-systems.M.S.Committee Chair: Prof. Rao R Tummala; Committee Member: Dr. Jack Moon; Committee Member: Dr. P M Ra

Thermo-mechanical analysis of flexible and stretchable systems

This paper presents a summary of the modeling and technology developed for flexible and stretchable electronics. The integration of ultra thin dies at package level, with thickness in the range of 20 to 30 μ m, into flexible and/or stretchable materials are demonstrated as well as the design and reliability test of stretchable metal interconnections at board level are analyzed by both experiments and finite element modeling. These technologies can achieve mechanically bendable and stretchable subsystems. The base substrate used for the fabrication of flexible circuits is a uniform polyimide layer, while silicones materials are preferred for the stretchable circuits. The method developed for chip embedding and interconnections is named Ultra Thin Chip Package (UTCP). Extensions of this technology can be achieved by stacking and embedding thin dies in polyimide, providing large benefits in electrical performance and still allowing some mechanical flexibility. These flexible circuits can be converted into stretchable circuits by replacing the relatively rigid polyimide by a soft and elastic silicone material. We have shown through finite element modeling and experimental validation that an appropriate thermo mechanical design is necessary to achieve mechanically reliable circuits and thermally optimized packages

Copper to copper bonding by nano interfaces for fine pitch interconnections and thermal applications

Ever growing demands for portability and functionality have always governed the electronic technology innovations. IC downscaling with Moore s law at IC level and system miniaturization with System-On-Package (SOP) paradigm at system level, have resulted and will continue to result in ultraminiaturized systems with unprecedented functionality at reduced cost. However, system miniaturization poses several electrical and thermal challenges that demand innovative solutions including advanced materials, bonding and assembly techniques. Heterogeneous material and device integration for thermal structures and IC assembly are limited by the bonding technology and the electrical and thermal impedance of the bonding interfaces. Solder - based bonding technology that is prevalent today is a major limitation to future systems. The trend towards miniaturized systems is expected to drive downscaling of IC I/O pad pitches from 40µm to 1- 5µm in future. Solder technology imposes several pitch, processability and cost restrictions at such fine pitches. Furthermore, according to International Technology Roadmap for Semiconductors (ITRS-2006), the supply current in high performance microprocessors is expected to increase to 220 A by 2012. At such supply current, the current density will exceed the maximum allowable current density of solders. The intrinsic delay and electromigration in solders are other daunting issues that become critical at nanometer sized technology nodes. In addition, formation of intermetallics is also a bottleneck that poses significant mechanical issues. Similarly, thermal power dissipation is growing to unprecedented high with a projected power of 198 W by 2008 (ITRS 2006). Present thermal interfaces are not adequate for such high heat dissipation. Recently, copper based thin film bonding has become a promising approach to address the abovementioned challenges. However, copper-copper direct bonding without using solders has not been studied thoroughly. Typically, bonding is carried out at 400oC for 30 min followed by annealing for 30 min. High thermal budget in such process makes it less attractive for integrated systems because of the associated process incompatibilities. Hence, there is a need to develop a novel low temperature copper to copper bonding process. In the present study, nanomaterials - based copper-to-copper bonding is explored and developed as an alternative to solder-based bonding. To demonstrate fine pitch bonding, the patterning of these nanoparticles is crucial. Therefore, two novel self-patterning techniques based on: 1.) Selective wetting and 2.) Selective nanoparticle deposition, are developed to address this challenge. Nanoparticle active layer facilitates diffusion and, thus, a reliable bond can be achieved using less thermal budget. Quantitative characterization of the bonding revealed good metallurgical bonding with very high bond strength. This has been confirmed by several morphological and structural characterizations. A 30-micron pitch IC assembly test vehicle is used to demonstrate fine pitch patternability and bonding. In conclusion, novel nanoparticle synthesis and patterning techniques were developed and demonstrated for low-impedance and low-cost electrical and thermal interfaces.M.S.Committee Chair: Rao R. Tummala; Committee Member: C. P. Wong; Committee Member: P. M. Ra

Modeling, design, and characterization of through vias in silicon and glass interposers

Advancements in very large scale integration (VLSI) technology have led to unprecedented transistor and interconnect scaling. Further miniaturization by traditional IC scaling in future planar CMOS technology faces significant challenges. Stacking of ICs (3D IC) using three dimensional (3D) integration technology helps in significantly reducing wiring lengths, interconnect latency and power dissipation while reducing the size of the chip and enhancing performance. Interposer technology with ultra-fine pitch interconnections needs to be developed to support the huge I/O connection requirement for packaging 3D ICs. Through vias in stacked silicon ICs and interposers are the key components of a 3D system. The objective of this dissertation is to model through vias in 3D silicon and glass interposers and, to address power and high-speed signal integrity issues in 3D interposers considering silicon biasing effects. An equivalent circuit model of the through via in silicon interposer (Si TPV) has been proposed considering the bias voltage dependent Metal-Oxide-Semiconductor (MOS) capacitance effect. Important design guidelines and optimizations are proposed for Si TPVs used in the signal delivery network, power delivery network (PDN), and as variable capacitors. Through vias in glass interposers (Glass TPVs) are modeled, designed and simulated by using electromagnetic field solvers. Signal and power integrity analyses are performed for silicon and glass interposers. PDN design is proposed by utilizing the MOS capacitance of the Si TPVs for decoupling.PhDCommittee Chair: Tummala, Rao; Committee Co-Chair: Swaminathan, Madhavan; Committee Member: Lim, Sung Kyu; Committee Member: Mukhopadhyay, Saibal; Committee Member: Sitaraman, Suresh; Committee Member: Sundaram, Venk

Compliant copper microwire arrays for reliable interconnections between large low-CTE packages and printed wiring board

The trend to high I/O density, performance and miniaturization at low cost is driving the industry towards shrinking interposer design rules, requiring a new set of packaging technologies. Low-CTE packages from silicon, glass and low-CTE organic substrates enable high interconnection density, high reliability and integration of system components. However, the large CTE mismatch between the package and the board presents reliability challenges for the board-level interconnections. Novel stress-relief structures that can meet reliability requirements along with electrical performance while meeting the cost constraints are needed to address these challenges. This thesis focuses on a comprehensive methodology starting with modeling, design, fabrication and characterization to validate such stress-relief structures. This study specifically explores SMT-compatible stress-relief microwire arrays in thin polymer carriers as a unique and low-cost solution for reliable board-level interconnections between large low-CTE packages and printed wiring boards. The microwire arrays are pre-fabricated in ultra-thin carriers using low-cost manufacturing processes such as laser vias and copper electroplating, which are then assembled in between the interposer and printed wiring board (PWB) as stress-relief interlayers. The microwire array results in dramatic reduction in solder stresses and strains, even with larger interposer sizes (20 mm × 20 mm), at finer pitch (400 microns), without the need for underfill. The parallel wire arrays result in low resistance and inductance, and therefore do not degrade the electrical performance. The scalability of the structures and the unique processes, from micro to nanowires, provides extendibility to finer pitch and larger package sizes. Finite element method (FEM) was used to study the reliability of the interconnections to provide guidelines for the test vehicle design. The models were built in 2.5D geometries to study the reliability of 400 µm-pitch interconnections with a 100 µm thick, 20 mm × 20 mm silicon package that was SMT-assembled onto an organic printed wiring board. The performance of the microwire array interconnection is compared to that of ball grid array (BGA) interconnections, in warpage, equivalent plastic strain and projected fatigue life. A unique set of materials and processes was used to demonstrate the low-cost fabrication of microwire arrays. Copper microwires with 12 µm diameter and 50 µm height were fabricated on both sides of a 50 µm thick, thermoplastic polymer carrier using dryfilm based photolithography and bottom-up electrolytic plating. The copper microwire interconnections were assembled between silicon interposer and FR-4 PWB through SMT-compatible process. Thermal mechanical reliability of the interconnections was characterized by thermal cycling test from -40°C to 125°C. The initial fatigue failure in the interconnections was identified at 700 cycles in the solder on the silicon package side, which is consistent with the modeling results. This study therefore demonstrated a highly-reliable and SMT-compatible solution for board-level interconnections between large low-CTE packages and printed wiring board.Ph.D

Materials for high-density electronic packaging and interconnection

Electronic packaging and interconnections are the elements that today limit the ultimate performance of advanced electronic systems. Materials in use today and those becoming available are critically examined to ascertain what actions are needed for U.S. industry to compete favorably in the world market for advanced electronics. Materials and processes are discussed in terms of the final properties achievable and systems design compatibility. Weak points in the domestic industrial capability, including technical, industrial philosophy, and political, are identified. Recommendations are presented for actions that could help U.S. industry regain its former leadership position in advanced semiconductor systems production

Thermo-Mechanical Reliability and Electrical Performance of Indium Interconnects and Under Bump Metallization

This thesis presents reliability analysis of indium interconnects and Under Bump Metallization (UBM) in flip chip devices. Flip chip assemblies with the use of bump interconnections are frequently used, especially in high density, three-dimensional electronic devices. Currently there are many methods for interconnect bumping, all of which require UBM. The UBM is required for interconnection, diffusion resistance and quality electrical contact between substrate and device. Bonded silicon test vehicles were comprised of Indium bumps and three UBM compositions: Ti/Ni/Au (200\xc5/1000\xc5/500\xc5), Ti/Ni (200\xc5/1000\xc5), Ni (1000\xc5). UBM and indium were deposited by evaporation and exposed to unbiased accelerated temperature cycling(-55°C to 125°C, 15°C/min ramp rate). Finite Element Analysis (FEA) simulations were used to gain understanding of non-linear strain behavior of indium interconnects during temperature cycling. Experimental testing coupled with FEA simulations facilitated cycle-to-failure calculations. FEA results show plastic strain concentrations within indium bump below failure limits. It has been demonstrated that fabrication of Ti/Ni/Au, Ti/Ni, and Ni UBM stacks performed reliably within infant mortality failure region

Channel Characterization for Chip-scale Wireless Communications within Computing Packages

Wireless Network-on-Chip (WNoC) appears as a promising alternative to conventional interconnect fabrics for chip-scale communications. WNoC takes advantage of an overlaid network composed by a set of millimeter-wave antennas to reduce latency and increase throughput in the communication between cores. Similarly, wireless inter-chip communication has been also proposed to improve the information transfer between processors, memory, and accelerators in multi-chip settings. However, the wireless channel remains largely unknown in both scenarios, especially in the presence of realistic chip packages. This work addresses the issue by accurately modeling flip-chip packages and investigating the propagation both its interior and its surroundings. Through parametric studies, package configurations that minimize path loss are obtained and the trade-offs observed when applying such optimizations are discussed. Single-chip and multi-chip architectures are compared in terms of the path loss exponent, confirming that the amount of bulk silicon found in the pathway between transmitter and receiver is the main determinant of losses.Comment: To be presented 12th IEEE/ACM International Symposium on Networks-on-Chip (NOCS 2018); Torino, Italy; October 201

Heterogeneous 2.5D integration on through silicon interposer

© 2015 AIP Publishing LLC. Driven by the need to reduce the power consumption of mobile devices, and servers/data centers, and yet continue to deliver improved performance and experience by the end consumer of digital data, the semiconductor industry is looking for new technologies for manufacturing integrated circuits (ICs). In this quest, power consumed in transferring data over copper interconnects is a sizeable portion that needs to be addressed now and continuing over the next few decades. 2.5D Through-Si-Interposer (TSI) is a strong candidate to deliver improved performance while consuming lower power than in previous generations of servers/data centers and mobile devices. These low-power/high-performance advantages are realized through achievement of high interconnect densities on the TSI (higher than ever seen on Printed Circuit Boards (PCBs) or organic substrates), and enabling heterogeneous integration on the TSI platform where individual ICs are assembled at close proximity