Directly Printed Nanomaterial Sensor for Strain and Vibration Measurement

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 기계공학부, 2020. 8. 안성훈.Most discussions about Industrie 4.0 tacitly assume that any such system would involve the processing and evaluation of large data volumes. Specifically, the operation of complex production processes requires stable and reliable data measurement and communication systems. However, while modern sensor technology may already be capable of collecting a wide range of machine and production data, it has been proving difficult to measure and analyse the data which is not easy to measurable and feed the results quickly back into an optimised production cycle. This is why the cost and installation of sensor, data acquisition, and transmission systems for flexible and adaptive manufacturing process have not been match the requirement of industrial demands. In this dissertation, directly printed nanomaterial sensor capable of strain and vibration measurement with high sensitivity and wide measurable range was fabricated using aerodynamically focused nanomaterial (AFN) printing system which is a direct printing technique for conductive and stretchable pattern printing onto flexible substrate. Specifically, microscale porous conductive pattern composed of silver nanoparticles (AgNPs) and multi-walled carbon nanotubes (MWCNTs) composite was printed onto polydimethylsiloxane (PDMS). Printing mechanism of AFN printing system for nanocomposite onto flexible substrate in order of mechanical crack generation, seed layer deposition, partial aggregation, and fully deposition was demonstrated and experimentally validated. The printed nanocomposite sensor exhibited gauge factor (GF) of 58.7, measurable range of 0.74, and variance in peak resistance under 0.05 during 1,000 times life cycle evaluation test. Furthermore, vibration measurement performance was evaluated according to vibration amplitude and frequency with Q-factor evaluation and statistical verification. Sensing mechanism for nanocomposite sensor was also analysed and discussed by both analytical and statistical methods. First, electron tunnelling effect among nanomaterials was analysed statistically using bivariate probit model. Since electrical property varies by the geometrical properties of nanomaterial, Monte Carlo simulation method based on Lennard-Jones (LJ) potential model and the voter model was developed for deeper understanding of the dynamics of nanomaterial by strain. By simply counting the average attachment among nanomaterials by strain, electrical conductivity was easily estimated with low simulation cost. The main objective of all processes to manufacture high-tech products is compliance with the specified ranges of permissible variation. In this perspective, all data must be recorded that might provide some evidence of status changes anywhere along the process chain. This dissertation covers the monitoring of forming and milling process. By measurement of mechanical deformation of stamp during forming process, it was possible to estimate the forming force according to various process parameters including maximum force, force gradient, and the thickness of sheet metal. Furthermore, accurate and reliable vibration monitoring was also conducted during milling process by simple and direct attachment of printed sensor to workpiece. Using frequency and power spectrum analysis of obtained data, the vibration of workpiece was measured during milling process according to process parameters including RPM, feed rate, cutting depth and width of spindle. Finally, developed sensor was applied to the digital twin of turbine blade manufacturing that vibration greatly affects the quality of product to predict the process defects in real time. To overcome the wire required data acquisition and transmission system, directly printed wireless communication sensor was also developed using chipless radio frequency identification (RFID) technology. It is one of the widely used technique for internet-of-things (IoT) devices due to low-cost, printability, and simplicity. The developed stretchable and chipless RFID sensor exhibited GF more than 0.6 and maximum measurable range more than 0.2 with high degree-of-freedom of motion. Since it showed its original characteristics of sensing in only one direction independently, sensor patch composed of various sensor with different resonance frequency was capable of measuring not only normal strains but also shear strains in all directions. Sensors in machinery and equipment can provide valuable clues as to whether or not the actual values will fall into the tolerance range. In this aspect, a real-time, accurate, and reliable process monitoring is a basic and crucial enabler of intelligent manufacturing operations and digital twin applications. In this dissertation, developed sensor was used for various manufacturing process include forming process, milling process, and wireless communication using highly sensitive and wide measuring properties with low fabrication cost. It is expected that developed sensor could be applied for the digital twin and process defects prediction in real-time.4차 산업혁명에 대한 대부분의 논의는 많은 양의 데이터를 처리하고 평가하는 시스템을 암묵적으로 가정한다. 특히, 복잡한 생산 공정을 운영하기 위해서는 안정적이고 신뢰할 수 있는 데이터 측정 및 통신 시스템이 필요하다. 하지만, 최신 센서 기술은 광범위한 기계 및 생산 공정 중 데이터를 수집하는 것이 가능하지만 측정하기 쉽지 않은 데이터를 측정하고 분석하여 그 결과를 최적화된 생산 공정에 신속하게 제공하는데 한계를 가지고 있다. 때문에, 유연하고 적응 가능한 제조 공정을 위한 센서의 가격과 설치 방법, 데이터 수집 및 전송 시스템이 실제 산업의 요구 사항에 도달하지 못하고 있다. 이 학위 논문에서는 유연 기판에 전도성 및 신축성 패턴을 직접 인쇄할 수 있는 공기역학적 나노물질 집속 인쇄 시스템을 사용하여 높은 민감도와 넓은 측정 가능 범위를 가진 변위 및 진동 센서를 개발하였다. 구체적으로, 은 나노입자와 다중 벽 탄소 나노튜브로 구성된 나노 복합재를 폴리디메틸실록산 위에 직접 인쇄하였다. 유연 기판 위에 공기역학적 나노물질 집속 인쇄 시스템을 사용한 나노 복합재 인쇄 방법의 기작이 기계적 균열 발생, 시드층 적층, 부분 응집 및 완전 증착 순으로 논의 및 실험적으로 검증되었다. 인쇄된 나노 복합재 센서는 58.7의 게이지 팩터, 0.74의 측정 가능 범위를 나타내었으며 1,000번 반복된 수명 주기 평가에서 5% 미만의 정점 저항 변화를 확인할 수 있었다. 또한 Q 인자 평가 및 통계 검증을 사용하여 진동의 진폭 및 주파수에 따른 진동 측정 성능을 평가하였다. 나노 복합재 센서에 대한 측정 기작 또한 해석적 및 통계적 방법으로 분석되었다. 먼저, 나노물질 간 터널 효과가 이변량 프로빗 모델을 통해 통계적으로 분석되었다. 센서의 전기적 물성이 나노물질의 기하학적 물성에 따라 상이하기 때문에 변위에 따른 나노물질의 동적인 이해를 위해 레너드존스 전위 및 유권자 모델을 기반으로 한 몬테카를로 시뮬레이션 방법이 개발되었다. 이를 활용하여 나노물질 간 평균 부착 수를 계산하여 낮은 비용으로 전기전도도를 추정할 수 있었다. 첨단 제품을 제조하기 위한 모든 공정의 주요 목표는 지정된 범위의 허용 가능한 변동을 준수하는 것이다. 이를 위해 공정 중 어디에서나 상태 변경의 증거를 제공할 수 있는 모든 데이터를 기록하는 것이 필수적이다. 이 학위 논문에서는 제작된 센서를 통해 성형 및 절삭 공정의 데이터를 기록함으로써 공정을 모니터링하였다. 성형 공정 동안 스탬프의 기계적 변형을 측정함으로써 최대 힘, 힘의 구배 및 판금의 두께를 포함하는 다양한 공정 변수에 따라 성형 힘을 추정할 수 있었다. 또한, 절삭 공정 중 공작물에 제작된 센서를 직접 부착하여 정확하고 안정적인 진동 모니터링을 수행하였다. 얻어진 데이터의 주파수 및 전력 스펙트럼 분석을 이용하여, 분당 회전 수, 이송 속도, 스핀들의 절삭 깊이 및 너비에 따른 공작물의 진동을 측정하였다. 마지막으로 제조된 센서를 진동이 제품 품질에 큰 영향을 미치는 터빈 동익 제조 공정의 디지털 트윈으로 적용하여 실시간으로 공정 결함을 예측하였다. 유선 데이터 수집 및 전송 시스템을 극복하기 위해 칩리스 무선 주파수 식별 기술을 사용하여 직접 인쇄된 무선 통신 센서를 개발하였다. 칩리스 무선 주파수 식별 기술은 저비용, 인쇄성 및 공정의 평이성으로 인해 사물 인터넷 장치에 널리 사용되는 기술 중 하나이다. 개발된 유연한 칩리스 센서는 0.6 이상의 게이지 팩터와 0.2 이상의 측정 가능 범위를 나타냈다. 또한 제작된 센서는 한 방향의 변위만 독립적으로 측정할 수 있는 특성을 가지고 있기 때문에, 모든 방향의 수직 및 전단 변형을 측정할 수 있는 다양한 공진 주파수로 구성된 센서 패치가 개발되었다. 기계 및 장비의 센서는 실제 값이 공차 범위에 속하는지 여부에 대한 중요한 단서를 제공할 수 있다. 이러한 측면에서, 정확하고 신뢰할 수 있는 실시간 공정 모니터링은 지능형 제조 공정 및 디지털 트윈으로의 응용을 위한 기본적이고 결정적인 요소이다. 이 학위 논문에서 개발된 센서는 낮은 제조 비용과 높은 민감도 및 신축성을 가지고 있기 때문에 성형 공정, 절삭 공정, 무선 통신을 포함한 다양한 제조 공정에서 응용되었다. 뿐만 아니라 제작된 센서는 디지털 트윈 및 공정 결함의 실시간 예측을 위해 다양하게 사용될 수 있을 것으로 예상된다.Chapter 1. Introduction 1 1.1. Toward smart manufacturing 1 1.2. Sensor in manufacturing 4 1.3. Research objective 11 Chapter 2. Background 16 2.1. Aerodynamically focused nanomaterial printing 16 2.2. Printing system envelope 26 2.3. Highly sensitive sensor printing 34 Chapter 3. Sensor fabrication and evaluation 42 3.1. Highly sensitive and wide measuring sensor printing 42 3.2. Sensing performance evaluation 59 3.3. Environmental and industrial evaluation 87 Chapter 4. Sensing mechanism analysis 97 4.1. Theoretical background 97 4.2. Statistical regression anaylsis 101 4.3. Monte Carlo simulation 104 Chapter 5. Application to process monitoring 126 5.1. Forming process monitoring 126 5.2. Milling process monitoring 133 5.3. Wireless communication monitoring 149 Chapter 6. Conclusion 185 Bibliography 192 Abstract in Korean 211Docto

Nonlinear Effects in Rolling Mills Dynamics

This paper intends to describe nonlinear effects occurring in rolling mills dynamics. That is necessarily for vibrations damping and reliable diagnostics of rolling mills equipment under non-stationary working conditions. Three types of nonlinear effects are investigated taking place in drivelines and stands of different design, namely, transient torsional vibrations in hot rolling mills, chatter vibrations in tandem cold rolling mills and parametrical vibrations in high-speed wire and rod rolling mills. The procedure is proposed for natural frequencies identification when short transient torque signals restrict application of the Fourier transform. Some considerations given on using nonlinear effects for wear diagnostics and vibrations control based on natural frequencies and modes analysis of multi-body systems

Conference on Thermal Issues in Machine Tools: Proceedings

Inhomogeneous and changing temperature distributions in machine tools lead to sometimes considerable quality problems in the manufacturing process. In addition, the switching on and off of aggregates, for example, leads to further fluctuations in the temperature field of machine tools. More than 100 specialists discussed these and other topics from the field of thermal research at the 1st Conference on Termal Issues in Machine Tools in Dresden from 22 to 23 March.:Efficient modelling and computation of structure-variable thermal behavior of machine tools S. Schroeder, A. Galant, B. Kauschinger, M. Beitelschmidt Parameter identification software for various thermal model types B. Hensel, S. Schroeder, K. Kabitzsch Minimising thermal error issues on turning centre M. Mareš, O. Horejš, J. Hornych The methods for controlled thermal deformations in machine tools A. P. Kuznetsov, H.-J. Koriath, A.O. Dorozhko Efficient FE-modelling of the thermo-elastic behaviour of a machine tool slide in lightweight design C. Peukert, J. Müller, M. Merx, A. Galant, A. Fickert, B. Zhou, S. Städtler, S. Ihlenfeldt, M. Beitelschmidt Development of a dynamic model for simulation of a thermoelectric self-cooling system for linear direct drives in machine tools E. Uhlmann, L. Prasol, S.Thom, S. Salein, R. Wiese System modelling and control concepts of different cooling system structures for machine tools J. Popken, L. Shabi, J. Weber, J. Weber The electric drive as a thermo-energetic black box S. Winkler, R. Werner Thermal error compensation on linear direct drive based on latent heat storage I. Voigt, S. Winkler, R. Werner, A. Bucht, W.-G. Drossel Industrial relevance and causes of thermal issues in machine tools M. Putz, C. Richter, J. Regel, M. Bräunig Clustering by optimal subsets to describe environment interdependencies J. Glänzel, R. Unger, S. Ihlenfeldt Using meta models for enclosures in machine tools F. Pavliček, D. P. Pamies, J. Mayr, S. Züst, P. Blaser, P. Hernández-Becerro, K. Wegener Model order reduction of thermal models of machine tools with varying boundary conditions P. Hernández-Becerro, J. Mayr, P. Blaser, F. Pavliček, K. Wegener Effectiveness of modelling the thermal behaviour of the ball screw unit with moving heat sources taken into account J. Jedrzejewski, Z. Kowal, W. Kwasny, Z. Winiarski Analyzing and optimizing the fluidic tempering of machine tool frames A. Hellmich, J. Glänzel, A. Pierer Thermo-mechanical interactions in hot stamping L. Penter, N. Pierschel Experimental analysis of the heat flux into the grinding tool in creep feed grinding with CBN abrasives C. Wrobel, D. Trauth, P. Mattfeld, F. Klocke Development of multidimensional characteristic diagrams for the real-time correction of thermally caused TCP-displacements in precise machining M. Putz, C. Oppermann, M. Bräunig Measurement of near cutting edge temperatures in the single point diamond turning process E. Uhlmann, D. Oberschmidt, S. Frenzel, J. Polte Investigation of heat flows during the milling processes through infrared thermography and inverse modelling T. Helmig, T. Augspurger, Y. Frekers, B. Döbbeler, F. Klocke, R. Kneer Thermally induced displacements of machine tool structure, tool and workpiece due to cutting processes O. Horejš, M. Mareš, J. Hornych A new calibration approach for a grey-box model for thermal error compensation of a C-Axis C. Brecher, R. Spierling, M. Fey Investigation of passive torque of oil-air lubricated angular contact ball bearing and its modelling J. Kekula, M. Sulitka, P. Kolář, P. Kohút, J. Shim, C. H. Park, J. Hwang Cooling strategy for motorized spindle based on energy and power criterion to reduce thermal errors S. Grama, A. N. Badhe, A. Mathur Cooling potential of heat pipes and heat exchangers within a machine tool spindleo B. Denkena, B. Bergman, H. Klemme, D. Dahlmann Structure model based correction of machine tools X. Thiem, B. Kauschinger, S. Ihlenfeldt Optimal temperature probe location for the compensation of transient thermal errors G. Aguirre, J. Cilla, J. Otaegi, H. Urreta Adaptive learning control for thermal error compensation on 5-axis machine tools with sudden boundary condition changes P. Blaser, J. Mayr, F. Pavliček, P. Hernández-Becerro, K. Wegener Hybrid correction of thermal errors using temperature and deformation sensors C. Naumann, C. Brecher, C. Baum, F. Tzanetos, S. Ihlenfeldt, M. Putz Optimal sensor placement based on model order reduction P. Benner, R. Herzog, N. Lang, I. Riedel, J. Saak Workpiece temperature measurement and stabilization prior to dimensional measurement N. S. Mian, S. Fletcher, A. P. Longstaff Measurement of test pieces for thermal induced displacements on milling machines H. Höfer, H. Wiemer Model reduction for thermally induced deformation compensation of metrology frames J. v. d. Boom Local heat transfer measurement A. Kuntze, S. Odenbach, W. Uffrecht Thermal error compensation of 5-axis machine tools using a staggered modelling approach J. Mayr, T. Tiberini. P. Blaser, K. Wegener Design of a Photogrammetric Measurement System for Displacement and Deformation on Machine Tools M. Riedel, J. Deutsch, J. Müller. S. Ihlenfeldt Thermography on Machine Tools M. Riedel, J. Deutsch, J. Müller, S. Ihlenfeldt Test piece for thermal investigations of 5-axis machine tolls by on-machine measurement M. Wiesener. P. Blaser, S. Böhl, J. Mayr, K. Wegene

High speed milling technological regimes, process condition and technological equipment condition influence on surface quality parameters of difficult to cut materials

[ES] La calidad superficial en las piezas mecanizadas depende del acabado superficial, resultado de las marcas dejadas por la herramienta durante el proceso de corte. Las aproximaciones teóricas tradicionales indican que estas marcas están relacionadas con los parámetros de corte (velocidad de corte, avance, profundidad de corte...), el tipo de máquina, el material de la pieza, la geometría de la herramienta, etc. Pero no todos los tipos de mecanizado y selección de materiales pueden dar un resultado ambiguo. Hoy en día, de manera progresiva, se están utilizando las técnicas de fresado de Alta Velocidad sobre materiales de difícil mecanizado cada vez más. El fresado de Alta Velocidad implica a un considerable número de parámetros del proceso que pueden afectar a la formación topográfica 3D de la superficie. La hipótesis de que los parámetros de rugosidad superficial dependen de las huellas dejadas por la herramienta, determinadas por las condiciones de trabajo y las propiedades del entorno, condujo al desarrollo de una metodología de investigación personalizada. Este trabajo de investigación muestra como la combinación de los parámetros, inclinación del eje de la herramienta, deflexión geométrica de la herramienta y comportamiento vibracional del entorno, influencian sobre el parámetro de rugosidad superficial 3D, Sz. El modelo general fue dividido en varias partes, donde se ha descrito la influencia de parámetros del proceso adicionales, siendo incluidos en el modelo general propuesto. El proceso incremental seguido permite al autor desarrollar un modelo matemático general, paso a paso, testeando y añadiendo los componentes que más afectan a la formación de la topografía de la superficie. En la primera parte de la investigación se seleccionó un proceso de fresado con herramientas de punta plana. Primero, se analiza la geometría de la herramienta, combinada con múltiples avances, para distinguir los principales parámetros que afectan a la rugosidad superficial. Se introduce un modelo de predicción con un componente básico para la altura de la rugosidad, obtenida por la geometría de la herramienta de corte. A continuación, se llevan a cabo experimentos más específicamente diseñados, variando parámetros tecnológicos. Esto empieza con el análisis de la inclinación del eje de la herramienta contra la mesa de fresado. Los especímenes de análisis son muestras con cuatro recorridos de corte rectos con corte en sentido contrario. Las trayectorias lineales con diferentes direcciones dan la oportunidad de analizar la inclinación del husillo de fresado en la máquina. Un análisis visual reveló diferencias entre direcciones de corte opuestas, así como marcas dejadas por el filo posterior de la herramienta. Considerando las desviaciones de las marcas de corte observadas en las imágenes de rugosidad superficial obtenidas a partir de las medidas, se introdujo un análisis sobre el comportamiento dinámico del equipo y de la herramienta de corte. Las vibraciones producen desviaciones en la mesa de fresado y en la herramienta de corte. Estas desviaciones fueron detectadas e incluidas en el modelo matemático para completar la precisión en la predicción del modelo. Finalmente, el modelo de predicción del parámetro de rugosidad Sz fue comprobado con un mayor número de parámetros del proceso. Los valores de Sz medidos y predichos, fueron comparados y analizados estadísticamente. Los resultados revelaron una mayor desviación de la rugosidad predicha en las muestras fabricadas con diferentes máquinas y con diferentes avances. Importantes conclusiones sobre la precisión del equipo de fabricación han sido extraídas y de ellas se desprende que la huella de la herramienta de corte está directamente relacionada con los parámetros de la topografía de la superficie. Además, la influencia de la huella está afectada por la geometría de la herramienta de corte, la rigidez de la herramienta y la precisión del equipo. La geometría de la herramienta conforma la base del parámetro Sz, desviación de la altura de la superficie. Las conclusiones alcanzadas son la base para recomendaciones prácticas, aplicables en la industria.[CA] La qualitat superficial en les peces mecanitzades depèn de l'acabat superficial, resultat de les marques deixades per l'eina durant el procés de tall. Les aproximacions teòriques tradicionals indiquen que aquestes marques estan relacionades amb els paràmetres de tall (velocitat de tall, avanç, profunditat de tall...), el tipus de màquina, el material de la peça, la geometria de l'eina, etc. Però no tots els tipus de mecanitzat i selecció de materials poden donar un resultat ambigu. Avui en dia, de manera progressiva, s'estan utilitzant les tècniques de fresat d'Alta Velocitat sobre materials de difícil mecanització cada vegada més. El fresat d'Alta Velocitat implica un considerable nombre de paràmetres del procés que poden afectar la formació topogràfica 3D de la superfície. La hipòtesi que els paràmetres de rugositat superficial depenen de les empremtes deixades per l'eina, determinades per les condicions de treball i les propietats de l'entorn, va conduir al desenvolupament d'una metodologia d'investigació personalitzada. Aquest treball de recerca mostra com la combinació dels paràmetres, inclinació de l'eix de l'eina, deflexió geomètrica de l'eina i comportament vibracional de l'entorn, influencien sobre el paràmetre de rugositat superficial 3D, Sz. El model general va ser dividit en diverses parts, on s'ha descrit la influència de paràmetres addicionals del procés, sent inclosos en el model general proposat. El procés incremental seguit permet a l'autor desenvolupar un model matemàtic general, pas a pas, testejant i afegint els components que més afecten a la formació de la topografia de la superfície. En la primera part de la investigació es va seleccionar un procés de fresat amb eines de punta plana. Primer, s'analitza la geometria de l'eina, combinada amb múltiples avanços, per distingir els principals paràmetres que afecten la rugositat superficial. S'introdueix un model de predicció amb un component bàsic per a l'altura de la rugositat, obtinguda a través de la geometria de l'eina de tall. A continuació, es duen a terme experiments més específicament dissenyats, variant paràmetres tecnològics. Això comença amb l'anàlisi de la inclinació de l'eix de l'eina contra la taula de fresat. Els espècimens d'anàlisi són mostres amb quatre recorreguts de tall rectes amb tall en sentit contrari. Les trajectòries lineals amb diferents direccions donen l'oportunitat d'analitzar la inclinació del fus de fresat en la màquina. Una anàlisi visual revelà diferències entre direccions de tall oposades, així com marques deixades pel tall posterior de l'eina. Considerant les desviacions de les marques de tall observades en les imatges de rugositat superficial obtingudes a partir de les mesures, es va introduir una anàlisi sobre el comportament dinàmic de l'equip i de l'eina de tall. Les vibracions produeixen desviacions en la taula de fresat i en l'eina de tall. Aquestes desviacions van ser detectades i incloses en el model matemàtic per completar la precisió en la predicció de el model. Finalment, el model de predicció de el paràmetre de rugositat Sz va ser comprovat amb un major nombre de paràmetres del procés. Els valors de Sz mesurats i predits, van ser comparats i analitzats estadísticament. Els resultats van revelar una major desviació de la rugositat predita en les mostres fabricades amb diferents màquines i amb diferents avanços. Importants conclusions sobre la precisió de l'equip de fabricació han estat extretes i d'elles es desprèn que l'empremta de l'eina de tall està directament relacionada amb els paràmetres de la topografia de la superfície. A més, la influència de la empremta està afectada per la geometria de l'eina de tall, la rigidesa de l'eina i la precisió de l'equip. La geometria de l'eina conforma la base del paràmetre Sz, desviació de l'altura de la superfície. Les conclusions assolides són la base per recomanacions pràctiques, aplicables en la indústria.[EN] Surface quality of machined parts highly depends on the surface texture that reflects the marks, left by the tool during the cutting process. The traditional theoretical approaches indicate that these marks are related to the cutting parameters (cutting speed, feed, depths of cut...), the machining type, the part material, the tool geometry, etc. But, different machining type and material selection can give a variable result. In nowadays, more progressively, High Speed milling techniques have been applied on hard-to-cut materials more and more extensively. High-speed milling involves a considerable number of process parameters that may affect the 3D surface topography formation. The hypothesis that surface topography parameters depends on the traces left by the tool, determined by working conditions and environmental properties, led to the development of a custom research methodology. This research work shows how the parameters combination, tool axis inclination, tool geometric deflection, cutting tool geometry and environment vibrational behavior, influence on 3D surface topography parameter Sz. The general model was divided in multiple parts, where additional process parameters influence has been described and included in general model proposed. The incremental process followed allows the author to develop a general mathematical model, step by step, testing and adding the components that affect surface topography formation the most. In the first part of the research a milling procedure with flat end milling tools was selected. First, tool geometry, combined with multiple cutting feed rates, is analyzed to distinguish the main parameters that affect surface topography. A prediction model is introduced with a basic topography height component, performed by cutting tool geometry. Next, specifically designed experiments were conducted, varying technological parameters. That starts with cutting tool axis inclination against the milling table analysis. The specimens of analysis are samples with 4 contrary aimed straight cutting paths. Linear paths in different directions give a chance to analyze milling machine spindle axis topography, as well as marks left from cutting tool back cutting edge. Considering the deviations of cutting marks observed in the images of the surface topography obtained through the measurements, the milling equipment and cutting tool dynamical behavior analysis were introduced. Vibrations produce deviations in the milling table and cutting tool. These deviations were detected and included in the mathematical model to complete the prediction model accuracy. Finally, the prediction model of the topography parameter SZ was tested with increased number of process parameters. Measured and predicted SZ values were compared and analyzed statistically. Results revealed high predicted topography deviation on samples manufactured with different machines and with different feed rates. Relevant conclusions about the manufacturing equipment accuracy have been drawn and they state that cutting tool's footprint is directly related with surface topography parameters. Besides, footprint influence is affected by cutting tool geometry, tool stiffness and equipment accuracy.Logins, A. (2021). High speed milling technological regimes, process condition and technological equipment condition influence on surface quality parameters of difficult to cut materials [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/164122TESI

12th International Conference on Vibrations in Rotating Machinery

Since 1976, the Vibrations in Rotating Machinery conferences have successfully brought industry and academia together to advance state-of-the-art research in dynamics of rotating machinery. 12th International Conference on Vibrations in Rotating Machinery contains contributions presented at the 12th edition of the conference, from industrial and academic experts from different countries. The book discusses the challenges in rotor-dynamics, rub, whirl, instability and more. The topics addressed include: - Active, smart vibration control - Rotor balancing, dynamics, and smart rotors - Bearings and seals - Noise vibration and harshness - Active and passive damping - Applications: wind turbines, steam turbines, gas turbines, compressors - Joints and couplings - Challenging performance boundaries of rotating machines - High power density machines - Electrical machines for aerospace - Management of extreme events - Active machines - Electric supercharging - Blades and bladed assemblies (forced response, flutter, mistuning) - Fault detection and condition monitoring - Rub, whirl and instability - Torsional vibration Providing the latest research and useful guidance, 12th International Conference on Vibrations in Rotating Machinery aims at those from industry or academia that are involved in transport, power, process, medical engineering, manufacturing or construction

Cold Micro Metal Forming

This open access book contains the research report of the Collaborative Research Center “Micro Cold Forming” (SFB 747) of the University of Bremen, Germany. The topical research focus lies on new methods and processes for a mastered mass production of micro parts which are smaller than 1mm (by forming in batch size higher than one million). The target audience primarily comprises research experts and practitioners in production engineering, but the book may also be of interest to graduate students alike

ESSE 2017. Proceedings of the International Conference on Environmental Science and Sustainable Energy

Environmental science is an interdisciplinary academic field that integrates physical-, biological-, and information sciences to study and solve environmental problems. ESSE - The International Conference on Environmental Science and Sustainable Energy provides a platform for experts, professionals, and researchers to share updated information and stimulate the communication with each other. In 2017 it was held in Suzhou, China June 23-25, 2017

12th International Conference on Vibrations in Rotating Machinery

Since 1976, the Vibrations in Rotating Machinery conferences have successfully brought industry and academia together to advance state-of-the-art research in dynamics of rotating machinery. 12th International Conference on Vibrations in Rotating Machinery contains contributions presented at the 12th edition of the conference, from industrial and academic experts from different countries. The book discusses the challenges in rotor-dynamics, rub, whirl, instability and more. The topics addressed include: - Active, smart vibration control - Rotor balancing, dynamics, and smart rotors - Bearings and seals - Noise vibration and harshness - Active and passive damping - Applications: wind turbines, steam turbines, gas turbines, compressors - Joints and couplings - Challenging performance boundaries of rotating machines - High power density machines - Electrical machines for aerospace - Management of extreme events - Active machines - Electric supercharging - Blades and bladed assemblies (forced response, flutter, mistuning) - Fault detection and condition monitoring - Rub, whirl and instability - Torsional vibration Providing the latest research and useful guidance, 12th International Conference on Vibrations in Rotating Machinery aims at those from industry or academia that are involved in transport, power, process, medical engineering, manufacturing or construction