Use of a thermal battery with a heat pump for low temperature electric vehicle operation

Below 10°C, electric vehicles suffer from reduced range, which can be as severe as a 70% reduction (at -26°C). This is due to reduced battery performance at low temperatures and increased cabin heating demand. Heat pumps have been shown to have good steady state performance, but suffer slow and inefficient transients, while thermal storage has been shown to provide large heat flows and reduced warm up times, but space for such thermal storage is limited. Here a heat pump is combined with an optimally designed thermal battery and the simulated results are presented with improvements to energy consumption demonstrated

Comparative analysis of battery electric vehicle thermal management systems under long-range drive cycles

Due to increasing regulation on emissions and shifting consumer preferences, the wide adoption of battery electric vehicles (BEV) hinges on research and development of technologies that can extend system range. This can be accomplished either by increasing the battery size or via more efficient operation of the electrical and thermal systems. This study endeavours to accomplish the latter through comparative investigation of BEV integrated thermal management system (ITMS) performance across a range of ambient conditions (-20 °C to 40 °C), cabin setpoints (18 °C to 24 °C), and six different ITMS architectures. A dynamic ITMS modelling framework for a long-range electric vehicle is established with comprehensive sub models for the operation of the drive train, power electronics, battery, vapor compression cycle components, and cabin conditioning in a comprehensive transient thermal system modelling environment. A baseline thermal management system is studied using this modelling framework, as well as four common thermal management systems found in literature. This study is novel for its combination of comprehensive BEV characterization, broad parametric analysis, and the long range BEV that is studied. Additionally, a novel low-temperature waste heat recovery (LT WHR) system is proposed and has shown achieve up to a 15% range increase at low temperatures compared to the baseline system, through the reduction of the necessary cabin ventilation loading. While this system shows performance improvements, the regular WHR system offers the greatest benefit, a 13.5% increase in cold climate range, for long-range BEV drive cycles in terms of system range and transient response without the need for additional thermal system equipment

Thermodynamic investigation of a shared cogeneration system with electrical cars for northern Europe climate

Transition to alternative energy systems is indicated by EU Commission as a suitable path to energy efficiency and energy saving in the next years. The aims are to decrease greenhouses gases emissions, relevance of fossil fuels in energy production and energy dependence on extra-EU countries. These goals can be achieved increasing renewable energy sources and/or efficiency on energy production processes. In this paper an innovative micro-cogeneration system for household application is presented: it covers heating, domestic hot water and electricity demands for a residential user. Solid oxide fuel cells, heat pump and Stirling engine are utilised as a system to achieve high energy conversion efficiency. A transition from traditional petrol cars to electric mobility is also considered and simulated here. Different types of fuel are considered to demonstrate the high versatility of the simulated cogeneration system by changing the pre-reformer of the fuel cell. Thermodynamic analysis is performed to prove high efficiency with the different fuels

Index to 1981 NASA Tech Briefs, volume 6, numbers 1-4

Short announcements of new technology derived from the R&D activities of NASA are presented. These briefs emphasize information considered likely to be transferrable across industrial, regional, or disciplinary lines and are issued to encourage commercial application. This index for 1981 Tech Briefs contains abstracts and four indexes: subject, personal author, originating center, and Tech Brief Number. The following areas are covered: electronic components and circuits, electronic systems, physical sciences, materials, life sciences, mechanics, machinery, fabrication technology, and mathematics and information sciences

Index to NASA Tech Briefs, 1975

This index contains abstracts and four indexes--subject, personal author, originating Center, and Tech Brief number--for 1975 Tech Briefs

A review of thermal management for Li-ion batteries: Prospects, challenges, and issues

Li-ion batteries are essential component in the current generation of electric vehicles. However, further pushing electric vehicles are concerned with battery life. Since the temperature dictates battery lifetime, it is crucial to manage the heat and keep the temperature at an acceptable range within the battery pack. The benefit of a cooling system is to prevent the premature degradation of battery life. This paper provides a critical review of the so far thermal management strategy dealing with temperature within the cells, module, and packs. This paper reviews the advantages and disadvantages of state of the art (traditional) thermal cooling system. In this paper, we have reviewed separately cell, module, and pack level cooling system. The battery thermal modeling techniques and cooling system design challenges are also reviewed. This paper also reviews the future cooling system for future vehicles with rising fast charge rate and these techniques can improve the limitations of the traditional cooling system. This paper also suggests the best suitable and economically viable technology for the upcoming EVs issues

Development of Integrated Models for Thermal Management in Hybrid Vehicles

[ES] En los últimos años, la industria de la automoción ha hecho un gran esfuerzo para producir sistemas de propulsión más eficientes y menos contaminantes sin menguar su rendimiento. Las nuevas regulaciones impuestas por las autoridades han empujado a la industria hacia la electrificación de los sistemas de propulsión mientras que las tecnologías desarrolladas para el sistema de propulsión convencional, basado en motores de combustión interna alternativos (MCIA), ya no son suficientes. El modelado numérico ha demostrado ser una herramienta indispensable para el diseño, desarrollo y optimización de sistemas de gestión térmica en trenes motrices electrificados, ahorrando costes y reduciendo el tiempo de desarrollo. La gestión térmica en los MCIA siempre ha sido importante para mejorar el consumo, las emisiones y la seguridad. Sin embargo, es todavía más importante en los sistemas de propulsión híbridos, a causa de la complejidad del sistema y al funcionamiento intermitente del MCIA. Además, los trenes motrices electrificados tienen varias fuentes de calor (es decir, MCIA, batería, máquina eléctrica) con diferentes requisitos de funcionamiento térmico. El objetivo principal de este trabajo ha sido desarrollar modelos térmicos para estudiar la mejora de los sistemas de gestión térmica en sistemas de propulsión electrificados (es decir, vehículo híbrido), estudiando y cuantificando la influencia de diferentes estrategias en el rendimiento, la seguridad y la eficiencia de los vehículos. La metodología desarrollada en este trabajo consistió tanto en la realización de experimentos como en el desarrollo de modelos numéricos. De hecho, se llevó a cabo una extensa campaña experimental para validar los diferentes modelos del tren motriz electrificado. Los datos obtenidos de las campañas experimentales sirvieron para calibrar y validar los modelos así como para corroborar los resultados obtenidos por los estudios numéricos. En primer lugar, se estudiaron las diferentes estrategias de gestión térmica de manera independiente para cada componente del tren motriz. Para el MCIA se estudió el uso de nanofluidos, el aislamiento del colector y puertos de escape, así como el cambio de volumen de sus circuitos hidráulicos. De igual forma, se evaluó el impacto de diferentes estrategias para la mejora térmica de las baterías. Además, el modelo de máquina eléctrica se utilizó para desarrollar pruebas experimentales que emulaban el daño térmico producido en ciclos reales de conducción. En segundo lugar, los modelos de tren motriz se integraron utilizando un estándar de co-simulación para evaluar el impacto de un sistema de gestión térmica integrado. Finalmente, se implementó un nuevo control del sistema de gestión de energía para evaluar el impacto de considerar el estado térmico del MCIA al momento de decidir la distribución de potencia del vehículo híbrido. Los resultados han demostrado que el uso de nanofluidos tiene un impacto muy limitado tanto en el MCIA como en el comportamiento térmico de la batería. Además, también mostraron que al reducir el volumen de refrigerante en un 45 %, la reducción en el tiempo de calentamiento del MCIA y el consumo de combustible en comparación con el caso baso fue del 7 % y del 0.4 %, respectivamente. Además, para condiciones de frio (7ºC), el impacto fue todavía mayor, obteniendo una reducción del tiempo de calentamiento y del consumo de combustible del 13 % y del 0.5 % respectivamente. Por otro lado, los resultados concluyeron que durante el calentamiento del MCIA, el sistema integrado de gestión térmica mejoró el consumo de energía en un 1.74 % y un 3 % para condiciones de calor (20ºC) y frío (-20ºC), respectivamente. Esto se debe al hecho que el sistema de gestión térmica integrado permite evitar la caída de temperatura del MCIA cuando el sistema de propulsión está en manera eléctrica pura.[CA] En els últims anys, la indústria de l'automoció ha fet un gran esforç per a produir sistemes de propulsió més eficients i menys contaminants sense minvar el seu rendiment. Les noves regulacions imposades per les autoritats han espentat a la indústria cap a l'electrificació dels sistemes de propulsió mentre que les tecnologies desenvolupades per al sistema de propulsió convencional, basat en motors de combustió interna alternatius (MCIA), ja no són suficients. El modelatge numèric ha demostrat ser una eina indispensable per al disseny, desenvolupament i optimització de sistemes de gestió tèrmica en trens motrius electrificats, estalviant costos i reduint el temps de desenvolupament. La gestió tèrmica en els MCIA sempre ha sigut important per a millorar el consum, les emissions i la seguretat. No obstant això, és encara més important en els sistemes de propulsió híbrids, a causa de la complexitat del sistema i al funcionament intermitent del MCIA. A més, els trens motrius electrificats tenen diverses fonts de calor (és a dir, MCIA, bateria, màquina elèctrica) amb diferents requisits de funcionament tèrmic. L'objectiu principal d'aquest treball va ser desenvolupar models tèrmics per a estudiar la millora dels sistemes de gestió tèrmica en sistemes de propulsió electrificats (és a dir, vehicle híbrid), estudiant i quantificant la influència de diferents estratègies en el rendiment, la seguretat i l'eficiència dels vehicles. La metodologia desenvolupada en aquest treball va consistir tant en la realització d'experiments com en el desenvolupament de models numèrics. De fet, es va dur a terme una extensa campanya experimental per a validar els diferents models del tren motriu electrificat. Les dades obtingudes de les campanyes experimentals van servir per a calibrar i validar els models així com per a corroborar els resultats obtinguts pels estudis numèrics. En primer lloc, es van estudiar les diferents estratègies de gestió tèrmica de manera independent per a cada component del tren motriu. Per al MCIA es va estudiar l'us de nanofluids, l'aïllament del col·lector i ports d'eixida així com el canvi de volum dels seus circuits hidràulics. D'igual forma, es va avaluar l'impacte de diferents estratègies per a la millora tèrmica de les bateries. A més, el model de màquina elèctrica es va utilitzar per a desenvolupar proves experimentals que emulaven el mal tèrmic produït en cicles reals de conducció. En segon lloc, els models de tren motriu es van integrar utilitzant un estàndard de co-simulació per a avaluar l'impacte d'un sistema de gestió tèrmica integrat. Finalment, es va implementar un nou control del sistema de gestió d'energia per a avaluar l'impacte de considerar l'estat tèrmic del MCIA al moment de decidir la distribució de potència del vehicle híbrid. Els resultats han demostrat que l'us de nanofluids té un impacte molt limitat tant en el MCIA com en el comportament tèrmic de la bateria. A més, també van mostrar que en reduir el volum de refrigerant en un 45 %, la reducció en el temps de calfament del MCIA i el consum de combustible en comparació amb el cas base va ser del 7 % i del 0.4 %, respectivament. A més, per a condicions de fred (-7ºC), l'impacte va ser encara major, obtenint una reducció del temps de calfament i del consum de combustible del 13 % i del 0.5 % respectivament. D'altra banda, els resultats van concloure que durant el calfament del MCIA, el sistema integrat de gestió tèrmica va millorar el consum d'energia en un 1.74 % i un 3 % per a condicions de calor (20ºC) i fred (-20ºC), respectivament. Això es deu al fet que el sistema de gestió tèrmica integrat permet evitar la caiguda de temperatura del MCIA quan el sistema de propulsió està en manera elèctrica pura.[EN] In recent years, the automotive industry has made a great effort to produce more efficient and less polluting propulsion systems without diminishing their performance. The new regulations imposed by the authorities have pushed the industry towards the electrification of powertrains while, technologies developed for the conventional propulsion system based on alternative internal combustion engines (ICEs), are no longer sufficient. Numerical modeling has proven to be an indispensable tool for the design, development and optimization of thermal management systems in electrified powertrains, saving costs and reducing development time. Thermal management in ICEs has always been important for improving consumption, emissions and safety. However, it is even more important in hybrid powertrains, due to the complexity of the system and the intermittent operation of the ICE. In addition, electrified powertrains have various heat sources (i.e., ICE, battery, Electric machine) with different thermal operating requirements. The main objective of this work was to develop thermal models to study the improvement of thermal management systems in electrified powertrains (i.e., hybrid electric vehicle), shedding light and quantifying the influence of different strategies on performance, safety and efficiency of the vehicles. The methodology developed in this paper consisted both in carrying out experiments and in developing numerical models. In fact, an extensive experimental campaign was carried out to validate the various models of the electrified powertrain. The data obtained from the experimental campaigns served to calibrate and validate the models as well as to corroborate the results obtained by the numerical studies. Firstly, the different thermal management strategies were studied independently for each component of the powertrain. For the ICE, the use of nanofluids, insulation of exhaust manifold and ports as well as the volume change of its hydraulic circuits were studied. Similarly, the impact of different strategies for the thermal improvement of batteries was evaluated. Furthermore, the electric machine model was used for developing experimental tests which emulated the thermal damage produced in real driving cycles. Secondly, the powertrain models were integrated using a co-simulation standard to assess the impact of an integrated thermal management system. Finally, a new control energy management system was implemented to assess the impact of considering the ICE thermal state when deciding the power split of the hybrid vehicle. The results have shown that the use of nanofluids has a very limited impact on both the ICE and the battery's thermal behaviour. In addition, they also showed that by reducing the volume of coolant by 45 %, the reduction in ICE warm up time and fuel consumption compared to the base case were 7 % and 0.4 %, respectively. In addition, for cold conditions (-7ºC), the impact was even greater, obtaining a reduction in warm up time and fuel consumption of 13 % and 0.5 % respectively. On the other hand, the results concluded that during the warming of ICE, the integrated thermal management system improved energy consumption by 1.74 % and 3 % for warm (20ºC) and cold (-20ºC) conditions, respectively. This is because the integrated TMS makes it possible to prevent the ICE temperature drop when the powertrain is in pure electric mode. Finally, significant gains during Worldwide harmonized Light vehicles Test Cycles (WLTC) and Real Driving Emissions (RDE) cycles were observed when the ICE thermal state was chosen when deciding the power distribution.The author would like to sincerely acknowledge the founding support pro- vided by Conselleria de Innovación, Universidades, Ciencia y Sociedad Digital in the framework of the Ayuda Predoctoral GVA. (ACIF/2020/234). Additionally the author would also acknowledge the support provided by Renault S.A.S.Dreif Bennany, A. (2023). Development of Integrated Models for Thermal Management in Hybrid Vehicles [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/19406

Exhaust system energy management of internal combustion engines

Today, the investigation of fuel economy improvements in internal combustion engines (ICEs) has become the most significant research interest among the automobile manufacturers and researchers. The scarcity of natural resources, progressively increasing oil prices, carbon dioxide taxation and stringent emission regulations all make fuel economy research relevant and compelling. The enhancement of engine performance solely using incylinder techniques is proving increasingly difficult and as a consequence the concept of exhaust energy recovery has emerged as an area of considerable interest. Three main energy recovery systems have been identified that are at various stages of investigation. Vapour power bottoming cycles and turbo-compounding devices have already been applied in commercially available marine engines and automobiles. Although the fuel economy benefits are substantial, system design implications have limited their adaptation due to the additional components and the complexity of the resulting system. In this context, thermo-electric (TE) generation systems, though still in their infancy for vehicle applications have been identified as attractive, promising and solid state candidates of low complexity. The performance of these devices is limited to the relative infancy of materials investigations and module architectures. There is great potential to be explored. The initial modelling work reported in this study shows that with current materials and construction technology, thermo-electric devices could be produced to displace the alternator of the light duty vehicles, providing the fuel economy benefits of 3.9%-4.7% for passenger cars and 7.4% for passenger buses. More efficient thermo-electric materials could increase the fuel economy significantly resulting in a substantially improved business case. The dynamic behaviour of the thermo-electric generator (TEG) applied in both, main exhaust gas stream and exhaust gas recirculation (EGR) path of light duty and heavy duty engines were studied through a series of experimental and modelling programs. The analyses of the thermo-electric generation systems have highlighted the need for advanced heat exchanger design as well as the improved materials to enhance the performance of these systems. These research requirements led to the need for a systems evaluation technique typified by hardware-in-the-loop (HIL) testing method to evaluate heat exchange and materials options. HIL methods have been used during this study to estimate both the output power and the exhaust back pressure created by the device. The work has established the feasibility of a new approach to heat exchange devices for thermo-electric systems. Based on design projections and the predicted performance of new materials, the potential to match the performance of established heat recovery methods has been demonstrated