7,540 research outputs found
Single-Event Upset Analysis and Protection in High Speed Circuits
The effect of single-event transients (SETs) (at a combinational node of a design) on the system reliability is becoming a big concern for ICs manufactured using advanced technologies. An SET at a node of combinational part may cause a transient pulse at the input of a flip-flop and consequently is latched in the flip-flop and generates a soft-error. When an SET conjoined with a transition at a node along a critical path of the combinational part of a design, a transient delay fault may occur at the input of a flip-flop. On the other hand, increasing pipeline depth and using low power techniques such as multi-level power supply, and multi-threshold transistor convert almost all paths in a circuit to critical ones. Thus, studying the behavior of the SET in these kinds of circuits needs special attention. This paper studies the dynamic behavior of a circuit with massive critical paths in the presence of an SET. We also propose a novel flip-flop architecture to mitigate the effects of such SETs in combinational circuits. Furthermore, the proposed architecture can tolerant a single event upset (SEU) caused by particle strike on the internal nodes of a flip-flo
Analog, hybrid, and digital simulation
Analog, hybrid, and digital computerized simulation technique
Cross-Layer Optimization for Power-Efficient and Robust Digital Circuits and Systems
With the increasing digital services demand, performance and power-efficiency
become vital requirements for digital circuits and systems. However, the
enabling CMOS technology scaling has been facing significant challenges of
device uncertainties, such as process, voltage, and temperature variations. To
ensure system reliability, worst-case corner assumptions are usually made in
each design level. However, the over-pessimistic worst-case margin leads to
unnecessary power waste and performance loss as high as 2.2x. Since
optimizations are traditionally confined to each specific level, those safe
margins can hardly be properly exploited.
To tackle the challenge, it is therefore advised in this Ph.D. thesis to
perform a cross-layer optimization for digital signal processing circuits and
systems, to achieve a global balance of power consumption and output quality.
To conclude, the traditional over-pessimistic worst-case approach leads to
huge power waste. In contrast, the adaptive voltage scaling approach saves
power (25% for the CORDIC application) by providing a just-needed supply
voltage. The power saving is maximized (46% for CORDIC) when a more aggressive
voltage over-scaling scheme is applied. These sparsely occurred circuit errors
produced by aggressive voltage over-scaling are mitigated by higher level error
resilient designs. For functions like FFT and CORDIC, smart error mitigation
schemes were proposed to enhance reliability (soft-errors and timing-errors,
respectively). Applications like Massive MIMO systems are robust against lower
level errors, thanks to the intrinsically redundant antennas. This property
makes it applicable to embrace digital hardware that trades quality for power
savings.Comment: 190 page
Progress of analog-hybrid computation
Review of fast analog/hybrid computer systems, integrated operational amplifiers, electronic mode-control switches, digital attenuators, and packaging technique
Embedding Logic and Non-volatile Devices in CMOS Digital Circuits for Improving Energy Efficiency
abstract: Static CMOS logic has remained the dominant design style of digital systems for
more than four decades due to its robustness and near zero standby current. Static
CMOS logic circuits consist of a network of combinational logic cells and clocked sequential
elements, such as latches and flip-flops that are used for sequencing computations
over time. The majority of the digital design techniques to reduce power, area, and
leakage over the past four decades have focused almost entirely on optimizing the
combinational logic. This work explores alternate architectures for the flip-flops for
improving the overall circuit performance, power and area. It consists of three main
sections.
First, is the design of a multi-input configurable flip-flop structure with embedded
logic. A conventional D-type flip-flop may be viewed as realizing an identity function,
in which the output is simply the value of the input sampled at the clock edge. In
contrast, the proposed multi-input flip-flop, named PNAND, can be configured to
realize one of a family of Boolean functions called threshold functions. In essence,
the PNAND is a circuit implementation of the well-known binary perceptron. Unlike
other reconfigurable circuits, a PNAND can be configured by simply changing the
assignment of signals to its inputs. Using a standard cell library of such gates, a technology
mapping algorithm can be applied to transform a given netlist into one with
an optimal mixture of conventional logic gates and threshold gates. This approach
was used to fabricate a 32-bit Wallace Tree multiplier and a 32-bit booth multiplier
in 65nm LP technology. Simulation and chip measurements show more than 30%
improvement in dynamic power and more than 20% reduction in core area.
The functional yield of the PNAND reduces with geometry and voltage scaling.
The second part of this research investigates the use of two mechanisms to improve
the robustness of the PNAND circuit architecture. One is the use of forward and reverse body biases to change the device threshold and the other is the use of RRAM
devices for low voltage operation.
The third part of this research focused on the design of flip-flops with non-volatile
storage. Spin-transfer torque magnetic tunnel junctions (STT-MTJ) are integrated
with both conventional D-flipflop and the PNAND circuits to implement non-volatile
logic (NVL). These non-volatile storage enhanced flip-flops are able to save the state of
system locally when a power interruption occurs. However, manufacturing variations
in the STT-MTJs and in the CMOS transistors significantly reduce the yield, leading
to an overly pessimistic design and consequently, higher energy consumption. A
detailed analysis of the design trade-offs in the driver circuitry for performing backup
and restore, and a novel method to design the energy optimal driver for a given yield is
presented. Efficient designs of two nonvolatile flip-flop (NVFF) circuits are presented,
in which the backup time is determined on a per-chip basis, resulting in minimizing
the energy wastage and satisfying the yield constraint. To achieve a yield of 98%,
the conventional approach would have to expend nearly 5X more energy than the
minimum required, whereas the proposed tunable approach expends only 26% more
energy than the minimum. A non-volatile threshold gate architecture NV-TLFF are
designed with the same backup and restore circuitry in 65nm technology. The embedded
logic in NV-TLFF compensates performance overhead of NVL. This leads to the
possibility of zero-overhead non-volatile datapath circuits. An 8-bit multiply-and-
accumulate (MAC) unit is designed to demonstrate the performance benefits of the
proposed architecture. Based on the results of HSPICE simulations, the MAC circuit
with the proposed NV-TLFF cells is shown to consume at least 20% less power and
area as compared to the circuit designed with conventional DFFs, without sacrificing
any performance.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201
Reports on Hybrid-computer Hardware
Hybrid computer and differential analyzer design and development for university instruction progra
Recommended from our members
Built-in self test of RF subsystems
textWith the rapid development of wireless and wireline communications, a variety of new standards and applications are emerging in the marketplace. In order to achieve higher levels of integration, RF circuits are frequently embedded into System on Chip (SoC) or System in Package (SiP) products. These developments, however, lead to new challenges in manufacturing test time and cost. Use of traditional RF test techniques requires expensive high frequency test instruments and long test time, which makes test one of the bottlenecks for reducing IC costs. This research is in the area of built-in self test technique for RF subsystems. In the test approach followed in this research, on-chip detectors are used to calculate circuits specifications, and data converters are used to collect the data for analysis by an on-chip processor. A novel on-chip amplitude detector has been designed and optimized for RF circuit specification test. By using on-chip detectors, both the system performance and specifications of the individual components can be accurately measured. On-chip measurement results need to be collected by Analog to Digital Converters (ADCs). A novel time domain, low power ADC has been designed for this purpose. The ADC architecture is based on a linear voltage controlled delay line. Using this structure results in a linear transfer function for the input dependent delay. The time delay difference is then compared to a reference to generate a digital code. Two prototype test chips were fabricated in commercial CMOS processes. One is for the RF transceiver front end with on-chip detectors; the other is for the test ADC. The 940MHz RF transceiver front-end was implemented with on-chip detectors in a 0.18 [micrometer] CMOS technology. The chips were mounted onto RF Printed Circuit Boards (PCBs), with tunable power supply and biasing knobs. The detector was characterized with measurements which show that the detector keeps linear performance over a wide input amplitude range of 500mV. Preliminary simulation and measurements show accurate transceiver performance prediction under process variations. A 300MS/s 6 bit ADC was designed using the novel time domain architecture in a 0.13 [micrometer] standard digital CMOS process. The simulation results show 36.6dB Signal to Noise Ratio (SNR), 34.1dB Signal to Noise and Distortion Ratio (SNDR) for 99MHz input, Differential Non-Linearity (DNL)<0.2 Least Significant Bit (LSB), and Integral Non-Linearity (INL)<0.5LSB. Overall chip power is 2.7mW with a 1.2V power supply. The built-in detector RF test was extended to a full transceiver RF front end test with a loop-back setup, so that measurements can be made to verify the benefits of the technique. The application of the approach to testing gain, linearity and noise figure was investigated. New detector types are also evaluated. In addition, the low-power delay-line based ADC was characterized and improved to facilitate gathering of data from the detector. Several improved ADC structures at the system level are also analyzed. The built-in detector based RF test technique enables the cost-efficient test for SoCs.Electrical and Computer Engineerin
On Borrowed Time -- Preventing Static Power Side-Channel Analysis
In recent years, static power side-channel analysis attacks have emerged as a
serious threat to cryptographic implementations, overcoming state-of-the-art
countermeasures against side-channel attacks. The continued down-scaling of
semiconductor process technology, which results in an increase of the relative
weight of static power in the total power budget of circuits, will only improve
the viability of static power side-channel analysis attacks. Yet, despite the
threat posed, limited work has been invested into mitigating this class of
attack. In this work we address this gap. We observe that static power
side-channel analysis relies on stopping the target circuit's clock over a
prolonged period, during which the circuit holds secret information in its
registers. We propose Borrowed Time, a countermeasure that hinders an
attacker's ability to leverage such clock control. Borrowed Time detects a
stopped clock and triggers a reset that wipes any registers containing
sensitive intermediates, whose leakages would otherwise be exploitable. We
demonstrate the effectiveness of our countermeasure by performing practical
Correlation Power Analysis attacks under optimal conditions against an AES
implementation on an FPGA target with and without our countermeasure in place.
In the unprotected case, we can recover the entire secret key using traces from
1,500 encryptions. Under the same conditions, the protected implementation
successfully prevents key recovery even with traces from 1,000,000 encryptions
Programmable CMOS Analog-to-Digital Converter Design and Testability
In this work, a programmable second order oversampling CMOS delta-sigma analog-to-digital converter (ADC) design in 0.5µm n-well CMOS processes is presented for integration in sensor nodes for wireless sensor networks. The digital cascaded integrator comb (CIC) decimation filter is designed to operate at three different oversampling ratios of 16, 32 and 64 to give three different resolutions of 9, 12 and 14 bits, respectively which impact the power consumption of the sensor nodes. Since the major part of power consumed in the CIC decimator is by the integrators, an alternate design is introduced by inserting coder circuits and reusing the same integrators for different resolutions and oversampling ratios to reduce power consumption. The measured peak signal-to-noise ratio (SNR) for the designed second order delta-sigma modulator is 75.6dB at an oversampling ratio of 64, 62.3dB at an oversampling ratio of 32 and 45.3dB at an oversampling ratio of 16. The implementation of a built-in current sensor (BICS) which takes into account the increased background current of defect-free circuits and the effects of process variation on ΔIDDQ testing of CMOS data converters is also presented. The BICS uses frequency as the output for fault detection in CUT. A fault is detected when the output frequency deviates more than ±10% from the reference frequency. The output frequencies of the BICS for various model parameters are simulated to check for the effect of process variation on the frequency deviation. A design for on-chip testability of CMOS ADC by linear ramp histogram technique using synchronous counter as register in code detection unit (CDU) is also presented. A brief overview of the histogram technique, the formulae used to calculate the ADC parameters, the design implemented in 0.5µm n-well CMOS process, the results and effectiveness of the design are described. Registers in this design are replaced by 6T-SRAM cells and a hardware optimized on-chip testability of CMOS ADC by linear ramp histogram technique using 6T-SRAM as register in CDU is presented. The on-chip linear ramp histogram technique can be seamlessly combined with ΔIDDQ technique for improved testability, increased fault coverage and reliable operation
Circuits and Systems Advances in Near Threshold Computing
Modern society is witnessing a sea change in ubiquitous computing, in which people have embraced computing systems as an indispensable part of day-to-day existence. Computation, storage, and communication abilities of smartphones, for example, have undergone monumental changes over the past decade. However, global emphasis on creating and sustaining green environments is leading to a rapid and ongoing proliferation of edge computing systems and applications. As a broad spectrum of healthcare, home, and transport applications shift to the edge of the network, near-threshold computing (NTC) is emerging as one of the promising low-power computing platforms. An NTC device sets its supply voltage close to its threshold voltage, dramatically reducing the energy consumption. Despite showing substantial promise in terms of energy efficiency, NTC is yet to see widescale commercial adoption. This is because circuits and systems operating with NTC suffer from several problems, including increased sensitivity to process variation, reliability problems, performance degradation, and security vulnerabilities, to name a few. To realize its potential, we need designs, techniques, and solutions to overcome these challenges associated with NTC circuits and systems. The readers of this book will be able to familiarize themselves with recent advances in electronics systems, focusing on near-threshold computing
- …