Power Droop Reduction In Logic BIST By Scan Chain Reordering

Significant peak power (PP), thus power droop (PD), during test is a serious concern for modern, complex ICs. In fact, the PD originated during the application of test vectors may produce a delay effect on the circuit under test signal transitions. This event may be erroneously recognized as presence of a delay fault, with consequent generation of an erroneous test fail, thus increasing yield loss. Several solutions have been proposed in the literature to reduce the PD during test of combinational ICs, while fewer approaches exist for sequential ICs. In this paper, we propose a novel approach to reduce peak power/power droop during test of sequential circuits with scan-based Logic BIST. In particular, our approach reduces the switching activity of the scan chains between following capture cycles. This is achieved by an original generation and arrangement of test vectors. The proposed approach presents a very low impact on fault coverage and test time

Testing of leakage current failure in ASIC devices exposed to total ionizing dose environment using design for testability techniques

Due to the advancements in technology, electronic devices have been relied upon to operate under harsh conditions. Radiation is one of the main causes of different failures of the electronics devices. According to the operation environment, the sources of the radiation can be terrestrial or extra-terrestrial. For terrestrial the devices can be used in nuclear reactors or biomedical devices where the radiation is man-made. While for the extra- terrestrial, the devices can be used in satellites, the international space station or spaceships, where the radiation comes from various sources like the Sun. According to the operation environment the effects of radiation differ. These effects falls under two categories, total ionizing dose effect (TID) and single event effects (SEEs). TID effects can be affect the delay and leakage current of CMOS circuits negatively. The affects can therefore hinder the integrated circuits\u27 operation. Before the circuits are used, particularly in critical radiation heavy applications like military and space, testing under radiation must be done to avoid any failures during operation. The standard in testing electronic devices is generating worst case test vectors (WCTVs) and under radiation using these vectors the circuits are tested. However, the generation of these WCTVs have been very challenging so this approach is rarely used for TIDs effects. Design for testability (DFT) have been widely used in the industry for digital circuits testing applications. DFT is usually used with automatic test patterns generation software to generate test vectors against fault models of manufacturer defects for application specific integrated circuit (ASIC.) However, it was never used to generate test vectors for leakage current testing induced in ASICs exposed to TID radiation environment. The purpose of the thesis is to use DFT to identify WCTVs for leakage current failures in sequential circuits for ASIC devices exposed to TID. A novel methodology was devised to identify these test vectors. The methodology is validated and compared to previous non DFT methods. The methodology is proven to overcome the limitation of previous methodologies

A comprehensive comparison between design for testability techniques for total dose testing of flash-based FPGAs

Radiation sources exist in different kinds of environments where electronic devices often operate. Correct device operation is usually affected negatively by radiation. The radiation resultant effect manifests in several forms depending on the operating environment of the device like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). CMOS circuits and Floating gate MOS circuits suffer from an increase in the delay and the leakage current due to TID effect. This may damage the proper operation of the integrated circuit. Exhaustive testing is needed for devices operating in harsh conditions like space and military applications to ensure correct operations in the worst circumstances. The use of worst case test vectors (WCTVs) for testing is strongly recommended by MIL-STD-883, method 1019, which is the standard describing the procedure for testing electronic devices under radiation. However, the difficulty of generating these test vectors hinders their use in radiation testing. Testing digital circuits in the industry is usually done nowadays using design for testability (DFT) techniques as they are very mature and can be relied on. DFT techniques include, but not limited to, ad-hoc technique, built-in self test (BIST), muxed D scan, clocked scan and enhanced scan. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Despite all these recommendations for DFT, radiation testing has not benefited from this reliable technology yet. Also, with the big variation in the DFT techniques, choosing the right technique is the bottleneck to achieve the best results for TID testing. In this thesis, a comprehensive comparison between different DFT techniques for TID testing of flash-based FPGAs is made to help designers choose the best suitable DFT technique depending on their application. The comparison includes muxed D scan technique, clocked scan technique and enhanced scan technique. The comparison is done using ISCAS-89 benchmarks circuits. Points of comparisons include FPGA resources utilization, difficulty of designs bring-up, added delay by DFT logic and robust testable paths in each technique

Built-In Self-Test Quality Assessment Using Hardware Fault Emulation in FPGAs

This paper addresses the problem of test quality assessment, namely of BIST solutions, implemented in FPGA and/or in ASIC, through Hardware Fault Emulation (HFE). A novel HFE methodology and tool is proposed, that, using partial reconfiguration, efficiently measures the quality of the BIST solution. The proposed HFE methodology uses Look-Up Tables (LUTs) fault models and is performed using local partial reconfiguration for fault injection on Xilinx(TM) Virtex and/or Spartan FPGA components, with small binary files. For ASIC cores, HFE is used to validate test vector selection to achieve high fault coverage on the physical structure. The methodology is fully automated. Results on ISCAS benchmarks and on an ARM core show that HFE can be orders of magnitude faster than software fault simulation or fully reconfigurable hardware fault emulation

A Hardware Security Solution against Scan-Based Attacks

Scan based Design for Test (DfT) schemes have been widely used to achieve high fault coverage for integrated circuits. The scan technique provides full access to the internal nodes of the device-under-test to control them or observe their response to input test vectors. While such comprehensive access is highly desirable for testing, it is not acceptable for secure chips as it is subject to exploitation by various attacks. In this work, new methods are presented to protect the security of critical information against scan-based attacks. In the proposed methods, access to the circuit containing secret information via the scan chain has been severely limited in order to reduce the risk of a security breach. To ensure the testability of the circuit, a built-in self-test which utilizes an LFSR as the test pattern generator (TPG) is proposed. The proposed schemes can be used as a countermeasure against side channel attacks with a low area overhead as compared to the existing solutions in literature

Design for testability of a latch-based design

Abstract. The purpose of this thesis was to decrease the area of digital logic in a power management integrated circuit (PMIC), by replacing selected flip-flops with latches. The thesis consists of a theory part, that provides background theory for the thesis, and a practical part, that presents a latch register design and design for testability (DFT) method for achieving an acceptable level of manufacturing fault coverage for it. The total area was decreased by replacing flip-flops of read-write and one-time programmable registers with latches. One set of negative level active primary latches were shared with all the positive level active latch registers in the same register bank. Clock gating was used to select which latch register the write data was loaded to from the primary latches. The latches were made transparent during the shift operation of partial scan testing. The observability of the latch register clock gating logic was improved by leaving the first bit of each latch register as a flip-flop. The controllability was improved by inserting control points. The latch register design, developed in this thesis, resulted in a total area decrease of 5% and a register bank area decrease of 15% compared to a flip-flop-based reference design. The latch register design manages to maintain the same stuck-at fault coverage as the reference design.Salpaperäisen piirin testattavuuden suunnittelu. Tiivistelmä. Tämän opinnäytetyön tarkoituksena oli pienentää digitaalisen logiikan pinta-alaa integroidussa tehonhallintapiirissä, korvaamalla valitut kiikut salpapiireillä. Opinnäytetyö koostuu teoriaosasta, joka antaa taustatietoa opinnäytetyölle, ja käytännön osuudesta, jossa esitellään salparekisteripiiri ja testattavuussuunnittelun menetelmä, jolla saavutettiin riittävän hyvä virhekattavuus salparekisteripiirille. Kokonaispinta-alaa pienennettiin korvaamalla luku-kirjoitusrekistereiden ja kerran ohjelmoitavien rekistereiden kiikut salpapiireillä. Yhdet negatiivisella tasolla aktiiviset isäntä-salpapiirit jaettiin kaikkien samassa rekisteripankissa olevien positiivisella tasolla aktiivisten salparekistereiden kanssa. Kellon portittamisella valittiin mihin salparekisteriin kirjoitusdata ladattiin yhteisistä isäntä-salpapireistä. Osittaisessa testipolkuihin perustuvassa testauksessa salpapiirit tehtiin läpinäkyviksi siirtooperaation aikana. Salparekisterin kellon portituslogiikan havaittavuutta parannettiin jättämällä jokaisen salparekisterin ensimmäinen bitti kiikuksi. Ohjattavuutta parannettiin lisäämällä ohjauspisteitä. Salparekisteripiiri, joka suunniteltiin tässä diplomityössä, pienensi kokonaispinta-alaa 5 % ja rekisteripankin pinta-alaa 15 % verrattuna kiikkuperäiseen vertailupiiriin. Salparekisteripiiri onnistuu pitämään saman juuttumisvikamallin virhekattavuuden kuin vertailupiiri

Evaluation of advanced techniques for structural FPGA self-test

This thesis presents a comprehensive test generation framework for FPGA logic elements and interconnects. It is based on and extends the current state-of-the-art. The purpose of FPGA testing in this work is to achieve reliable reconfiguration for a FPGA-based runtime reconfigurable system. A pre-configuration test is performed on a portion of the FPGA before it is reconfigured as part of the system to ensure that the FPGA fabric is fault-free. The implementation platform is the Xilinx Virtex-5 FPGA family. Existing literature in FPGA testing is evaluated and reviewed thoroughly. The various approaches are compared against one another qualitatively and the approach most suitable to the target platform is chosen. The array testing method is employed in testing the FPGA logic for its low hardware overhead and optimal test time. All tests are additionally pipelined to reduce test application time and use a high test clock frequency. A hybrid fault model including both structural and functional faults is assumed. An algorithm for the optimization of the number of required FPGA test configurations is developed and implemented in Java using a pseudo-random set-covering heuristic. Optimal solutions are obtained for Virtex-5 logic slices. The algorithm effort is parameterizable with the number of loop iterations each of which take approximately one second for a Virtex-5 sliceL circuit. A flexible test architecture for interconnects is developed. Arbitrary wire types can be tested in the same test configuration with no hardware overhead. Furthermore, a routing algorithm is integrated with the test template generation to select the wires under test and route them appropriately. Nine test configurations are required to achieve full test coverage for the FPGA logic. For interconnect testing, a local router-based on depth-first graph traversal is implemented in Java as the basis for creating systematic interconnect test templates. Pent wire testing is additionally implemented as a proof of concept. The test clock frequency for all tests exceeds 170 MHz and the hardware overhead is always lower than seven CLBs. All implemented tests are parameterizable such that they can be applied to any portion of the FPGA regardless of size or position

Identifying worst case test vectors for FPGA exposed to total ionization dose using design for testability techniques

Electronic devices often operate in harsh environments which contain a variation of radiation sources. Radiation may cause different kinds of damage to proper operation of the devices. Their sources can be found in terrestrial environments, or in extra-terrestrial environments like in space, or in man-made radiation sources like nuclear reactors, biomedical devices and high energy particles physics experiments equipment. Depending on the operation environment of the device, the radiation resultant effect manifests in several forms like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). TID effect causes an increase in the delay and the leakage current of CMOS circuits which may damage the proper operation of the integrated circuit. To ensure proper operation of these devices under radiation, thorough testing must be made especially in critical applications like space and military applications. Although the standard which describes the procedure for testing electronic devices under radiation emphasizes the use of worst case test vectors (WCTVs), they are never used in radiation testing due to the difficulty of generating these vectors for circuits under test. For decades, design for testability (DFT) has been the best choice for test engineers to test digital circuits in industry. It has become a very mature technology that can be relied on. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Surprisingly, however, radiation testing has not yet made use of this reliable technology. In this thesis, a novel methodology is proposed to extend the usage of DFT to generate WCTVs for delay failure in Flash based field programmable gate arrays (FPGAs) exposed to total ionizing dose (TID). The methodology is validated using MicroSemi ProASIC3 FPGA and cobalt 60 facility

Impact of LFSR Seeding on the Test Pattern Generator in BIST

This paper considers the problem of minimizing the power required to test a BIST based combinational circuit without modifying the test pattern generator and with no extra area or delay overhead. The objective of this paper is to analyze the impact of the polynomial and seed selection of the LFSR on the power consumed by the circuit. It is shown that proper selection of the seed of the LFSR can lead to significant decrease in the power consumption of the BIST sessions. For this purpose, a Bit Flipping LFSR is used as a test pattern generator in the BIST design. Experimental results using the ISCAS benchmark circuits are reported, showing variations of the seed selected for the LFSR, the power consumed is ranging from 5.5% to 13.5%