Doctor of Philosophy

dissertationIn recent years, a number of trends have started to emerge, both in microprocessor and application characteristics. As per Moore's law, the number of cores on chip will keep doubling every 18-24 months. International Technology Roadmap for Semiconductors (ITRS) reports that wires will continue to scale poorly, exacerbating the cost of on-chip communication. Cores will have to navigate an on-chip network to access data that may be scattered across many cache banks. The number of pins on the package, and hence available off-chip bandwidth, will at best increase at sublinear rate and at worst, stagnate. A number of disruptive memory technologies, e.g., phase change memory (PCM) have begun to emerge and will be integrated into the memory hierarchy sooner than later, leading to non-uniform memory access (NUMA) hierarchies. This will make the cost of accessing main memory even higher. In previous years, most of the focus has been on deciding the memory hierarchy level where data must be placed (L1 or L2 caches, main memory, disk, etc.). However, in modern and future generations, each level is getting bigger and its design is being subjected to a number of constraints (wire delays, power budget, etc.). It is becoming very important to make an intelligent decision about where data must be placed within a level. For example, in a large non-uniform access cache (NUCA), we must figure out the optimal bank. Similarly, in a multi-dual inline memory module (DIMM) non uniform memory access (NUMA) main memory, we must figure out the DIMM that is the optimal home for every data page. Studies have indicated that heterogeneous main memory hierarchies that incorporate multiple memory technologies are on the horizon. We must develop solutions for data management that take heterogeneity into account. For these memory organizations, we must again identify the appropriate home for data. In this dissertation, we attempt to verify the following thesis statement: "Can low-complexity hardware and OS mechanisms manage data placement within each memory hierarchy level to optimize metrics such as performance and/or throughput?" In this dissertation we argue for a hardware-software codesign approach to tackle the above mentioned problems at different levels of the memory hierarchy. The proposed methods utilize techniques like page coloring and shadow addresses and are able to handle a large number of problems ranging from managing wire-delays in large, shared NUCA caches to distributing shared capacity among different cores. We then examine data-placement issues in NUMA main memory for a many-core processor with a moderate number of on-chip memory controllers. Using codesign approaches, we achieve efficient data placement by modifying the operating system's (OS) page allocation algorithm for a wide variety of main memory architectures

Exploiting cache locality at run-time

With the increasing gap between the speeds of the processor and memory system, memory access has become a major performance bottleneck in modern computer systems. Recently, Symmetric Multi-Processor (SMP) systems have emerged as a major class of high-performance platforms. Improving the memory performance of Parallel applications with dynamic memory-access patterns on Symmetric Multi-Processors (SMP) is a hard problem. The solution to this problem is critical to the successful use of the SMP systems because dynamic memory-access patterns occur in many real-world applications. This dissertation is aimed at solving this problem.;Based on a rigorous analysis of cache-locality optimization, we propose a memory-layout oriented run-time technique to exploit the cache locality of parallel loops. Our technique have been implemented in a run-time system. Using simulation and measurement, we have shown our run-time approach can achieve comparable performance with compiler optimizations for those regular applications, whose load balance and cache locality can be well optimized by tiling and other program transformations. However, our approach was shown to improve significantly the memory performance for applications with dynamic memory-access patterns. Such applications are usually hard to optimize with static compiler optimizations.;Several contributions are made in this dissertation. We present models to characterize the complexity and present a solution framework for optimizing cache locality. We present an effective estimation technique for memory-access patterns to support efficient locality optimizations and information integration. We present a memory-layout oriented run-time technique for locality optimization. We present efficient scheduling algorithms to trade off locality and load imbalance. We provide a detailed performance evaluation of the run-time technique

Adaptive memory hierarchies for next generation tiled microarchitectures

Les últimes dècades el rendiment dels processadors i de les memòries ha millorat a diferent ritme, limitant el rendiment dels processadors i creant el conegut memory gap. Sol·lucionar aquesta diferència de rendiment és un camp d'investigació d'actualitat i que requereix de noves sol·lucions. Una sol·lució a aquest problema són les memòries “cache”, que permeten reduïr l'impacte d'unes latències de memòria creixents i que conformen la jerarquia de memòria. La majoria de d'organitzacions de les “caches” estan dissenyades per a uniprocessadors o multiprcessadors tradicionals. Avui en dia, però, el creixent nombre de transistors disponible per xip ha permès l'aparició de xips multiprocessador (CMPs). Aquests xips tenen diferents propietats i limitacions i per tant requereixen de jerarquies de memòria específiques per tal de gestionar eficientment els recursos disponibles. En aquesta tesi ens hem centrat en millorar el rendiment i la eficiència energètica de la jerarquia de memòria per CMPs, des de les “caches” fins als controladors de memòria. A la primera part d'aquesta tesi, s'han estudiat organitzacions tradicionals per les “caches” com les privades o compartides i s'ha pogut constatar que, tot i que funcionen bé per a algunes aplicacions, un sistema que s'ajustés dinàmicament seria més eficient. Tècniques com el Cooperative Caching (CC) combinen els avantatges de les dues tècniques però requereixen un mecanisme centralitzat de coherència que té un consum energètic molt elevat. És per això que en aquesta tesi es proposa el Distributed Cooperative Caching (DCC), un mecanisme que proporciona coherència en CMPs i aplica el concepte del cooperative caching de forma distribuïda. Mitjançant l'ús de directoris distribuïts s'obté una sol·lució més escalable i que, a més, disposa d'un mecanisme de marcatge més flexible i eficient energèticament. A la segona part, es demostra que les aplicacions fan diferents usos de la “cache” i que si es realitza una distribució de recursos eficient es poden aprofitar els que estan infrautilitzats. Es proposa l'Elastic Cooperative Caching (ElasticCC), una organització capaç de redistribuïr la memòria “cache” dinàmicament segons els requeriments de cada aplicació. Una de les contribucions més importants d'aquesta tècnica és que la reconfiguració es decideix completament a través del maquinari i que tots els mecanismes utilitzats es basen en estructures distribuïdes, permetent una millor escalabilitat. ElasticCC no només és capaç de reparticionar les “caches” segons els requeriments de cada aplicació, sinó que, a més a més, és capaç d'adaptar-se a les diferents fases d'execució de cada una d'elles. La nostra avaluació també demostra que la reconfiguració dinàmica de l'ElasticCC és tant eficient que gairebé proporciona la mateixa taxa de fallades que una configuració amb el doble de memòria.Finalment, la tesi es centra en l'estudi del comportament de les memòries DRAM i els seus controladors en els CMPs. Es demostra que, tot i que els controladors tradicionals funcionen eficientment per uniprocessadors, en CMPs els diferents patrons d'accés obliguen a repensar com estan dissenyats aquests sistemes. S'han presentat múltiples sol·lucions per CMPs però totes elles es veuen limitades per un compromís entre el rendiment global i l'equitat en l'assignació de recursos. En aquesta tesi es proposen els Thread Row Buffers (TRBs), una zona d'emmagatenament extra a les memòries DRAM que permetria guardar files de dades específiques per a cada aplicació. Aquest mecanisme permet proporcionar un accés equitatiu a la memòria sense perjudicar el seu rendiment global. En resum, en aquesta tesi es presenten noves organitzacions per la jerarquia de memòria dels CMPs centrades en la escalabilitat i adaptativitat als requeriments de les aplicacions. Els resultats presentats demostren que les tècniques proposades proporcionen un millor rendiment i eficiència energètica que les millors tècniques existents fins a l'actualitat.Processor performance and memory performance have improved at different rates during the last decades, limiting processor performance and creating the well known "memory gap". Solving this performance difference is an important research field and new solutions must be proposed in order to have better processors in the future. Several solutions exist, such as caches, that reduce the impact of longer memory accesses and conform the system memory hierarchy. However, most of the existing memory hierarchy organizations were designed for single processors or traditional multiprocessors. Nowadays, the increasing number of available transistors has allowed the apparition of chip multiprocessors, which have different constraints and require new ad-hoc memory systems able to efficiently manage memory resources. Therefore, in this thesis we have focused on improving the performance and energy efficiency of the memory hierarchy of chip multiprocessors, ranging from caches to DRAM memories. In the first part of this thesis we have studied traditional cache organizations such as shared or private caches and we have seen that they behave well only for some applications and that an adaptive system would be desirable. State-of-the-art techniques such as Cooperative Caching (CC) take advantage of the benefits of both worlds. This technique, however, requires the usage of a centralized coherence structure and has a high energy consumption. Therefore we propose the Distributed Cooperative Caching (DCC), a mechanism to provide coherence to chip multiprocessors and apply the concept of cooperative caching in a distributed way. Through the usage of distributed directories we obtain a more scalable solution and, in addition, has a more flexible and energy-efficient tag allocation method. We also show that applications make different uses of cache and that an efficient allocation can take advantage of unused resources. We propose Elastic Cooperative Caching (ElasticCC), an adaptive cache organization able to redistribute cache resources dynamically depending on application requirements. One of the most important contributions of this technique is that adaptivity is fully managed by hardware and that all repartitioning mechanisms are based on distributed structures, allowing a better scalability. ElasticCC not only is able to repartition cache sizes to application requirements, but also is able to dynamically adapt to the different execution phases of each thread. Our experimental evaluation also has shown that the cache partitioning provided by ElasticCC is efficient and is almost able to match the off-chip miss rate of a configuration that doubles the cache space. Finally, we focus in the behavior of DRAM memories and memory controllers in chip multiprocessors. Although traditional memory schedulers work well for uniprocessors, we show that new access patterns advocate for a redesign of some parts of DRAM memories. Several organizations exist for multiprocessor DRAM schedulers, however, all of them must trade-off between memory throughput and fairness. We propose Thread Row Buffers, an extended storage area in DRAM memories able to store a data row for each thread. This mechanism enables a fair memory access scheduling without hurting memory throughput. Overall, in this thesis we present new organizations for the memory hierarchy of chip multiprocessors which focus on the scalability and of the proposed structures and adaptivity to application behavior. Results show that the presented techniques provide a better performance and energy-efficiency than existing state-of-the-art solutions

"Virtual malleability" applied to MPI jobs to improve their execution in a multiprogrammed environment"

This work focuses on scheduling of MPI jobs when executing in shared-memory multiprocessors (SMPs). The objective was to obtain the best performance in response time in multiprogrammed multiprocessors systems using batch systems, assuming all the jobs have the same priority. To achieve that purpose, the benefits of supporting malleability on MPI jobs to reduce fragmentation and consequently improve the performance of the system were studied. The contributions made in this work can be summarized as follows:· Virtual malleability: A mechanism where a job is assigned a dynamic processor partition, where the number of processes is greater than the number of processors. The partition size is modified at runtime, according to external requirements such as the load of the system, by varying the multiprogramming level, making the job contend for resources with itself. In addition to this, a mechanism which decides at runtime if applying local or global process queues to an application depending on the load balancing between processes of it. · A job scheduling policy, that takes decisions such as how many processes to start with and the maximum multiprogramming degree based on the type and number of applications running and queued. Moreover, as soon as a job finishes execution and where there are queued jobs, this algorithm analyzes whether it is better to start execution of another job immediately or just wait until there are more resources available. · A new alternative to backfilling strategies for the problema of window execution time expiring. Virtual malleability is applied to the backfilled job, reducing its partition size but without aborting or suspending it as in traditional backfilling. The evaluation of this thesis has been done using a practical approach. All the proposals were implemented, modifying the three scheduling levels: queuing system, processor scheduler and runtime library. The impact of the contributions were studied under several types of workloads, varying machine utilization, communication and, balance degree of the applications, multiprogramming level, and job size. Results showed that it is possible to offer malleability over MPI jobs. An application obtained better performance when contending for the resources with itself than with other applications, especially in workloads with high machine utilization. Load imbalance was taken into account obtaining better performance if applying the right queue type to each application independently.The job scheduling policy proposed exploited virtual malleability by choosing at the beginning of execution some parameters like the number of processes and maximum multiprogramming level. It performed well under bursty workloads with low to medium machine utilizations. However as the load increases, virtual malleability was not enough. That is because, when the machine is heavily loaded, the jobs, once shrunk are not able to expand, so they must be executed all the time with a partition smaller than the job size, thus degrading performance. Thus, at this point the job scheduling policy concentrated just in moldability.Fragmentation was alleviated also by applying backfilling techniques to the job scheduling algorithm. Virtual malleability showed to be an interesting improvement in the window expiring problem. Backfilled jobs even on a smaller partition, can continue execution reducing memory swapping generated by aborts/suspensions In this way the queueing system is prevented from reinserting the backfilled job in the queue and re-executing it in the future.Postprint (published version

Software Coherence in Multiprocessor Memory Systems

Processors are becoming faster and multiprocessor memory interconnection systems are not keeping up. Therefore, it is necessary to have threads and the memory they access as near one another as possible. Typically, this involves putting memory or caches with the processors, which gives rise to the problem of coherence: if one processor writes an address, any other processor reading that address must see the new value. This coherence can be maintained by the hardware or with software intervention. Systems of both types have been built in the past; the hardware-based systems tended to outperform the software ones. However, the ratio of processor to interconnect speed is now so high that the extra overhead of the software systems may no longer be significant. This issue is explored both by implementing a software maintained system and by introducing and using the technique of offline optimal analysis of memory reference traces. It finds that in properly built systems, software maintained coherence can perform comparably to or even better than hardware maintained coherence. The architectural features necessary for efficient software coherence to be profitable include a small page size, a fast trap mechanism, and the ability to execute instructions while remote memory references are outstanding

Parallel architectures and runtime systems co-design for task-based programming models

The increasing parallelism levels in modern computing systems has extolled the need for a holistic vision when designing multiprocessor architectures taking in account the needs of the programming models and applications. Nowadays, system design consists of several layers on top of each other from the architecture up to the application software. Although this design allows to do a separation of concerns where it is possible to independently change layers due to a well-known interface between them, it is hampering future systems design as the Law of Moore reaches to an end. Current performance improvements on computer architecture are driven by the shrinkage of the transistor channel width, allowing faster and more power efficient chips to be made. However, technology is reaching physical limitations were the transistor size will not be able to be reduced furthermore and requires a change of paradigm in systems design. This thesis proposes to break this layered design, and advocates for a system where the architecture and the programming model runtime system are able to exchange information towards a common goal, improve performance and reduce power consumption. By making the architecture aware of runtime information such as a Task Dependency Graph (TDG) in the case of dataflow task-based programming models, it is possible to improve power consumption by exploiting the critical path of the graph. Moreover, the architecture can provide hardware support to create such a graph in order to reduce the runtime overheads and making possible the execution of fine-grained tasks to increase the available parallelism. Finally, the current status of inter-node communication primitives can be exposed to the runtime system in order to perform a more efficient communication scheduling, and also creates new opportunities of computation and communication overlap that were not possible before. An evaluation of the proposals introduced in this thesis is provided and a methodology to simulate and characterize the application behavior is also presented.El aumento del paralelismo proporcionado por los sistemas de cómputo modernos ha provocado la necesidad de una visión holística en el diseño de arquitecturas multiprocesador que tome en cuenta las necesidades de los modelos de programación y las aplicaciones. Hoy en día el diseño de los computadores consiste en diferentes capas de abstracción con una interfaz bien definida entre ellas. Las limitaciones de esta aproximación junto con el fin de la ley de Moore limitan el potencial de los futuros computadores. La mayoría de las mejoras actuales en el diseño de los computadores provienen fundamentalmente de la reducción del tamaño del canal del transistor, lo cual permite chips más rápidos y con un consumo eficiente sin apenas cambios fundamentales en el diseño de la arquitectura. Sin embargo, la tecnología actual está alcanzando limitaciones físicas donde no será posible reducir el tamaño de los transistores motivando así un cambio de paradigma en la construcción de los computadores. Esta tesis propone romper este diseño en capas y abogar por un sistema donde la arquitectura y el sistema de tiempo de ejecución del modelo de programación sean capaces de intercambiar información para alcanzar una meta común: La mejora del rendimiento y la reducción del consumo energético. Haciendo que la arquitectura sea consciente de la información disponible en el modelo de programación, como puede ser el grafo de dependencias entre tareas en los modelos de programación dataflow, es posible reducir el consumo energético explotando el camino critico del grafo. Además, la arquitectura puede proveer de soporte hardware para crear este grafo con el objetivo de reducir el overhead de construir este grado cuando la granularidad de las tareas es demasiado fina. Finalmente, el estado de las comunicaciones entre nodos puede ser expuesto al sistema de tiempo de ejecución para realizar una mejor planificación de las comunicaciones y creando nuevas oportunidades de solapamiento entre cómputo y comunicación que no eran posibles anteriormente. Esta tesis aporta una evaluación de todas estas propuestas, así como una metodología para simular y caracterizar el comportamiento de las aplicacionesPostprint (published version