Power-efficient high-speed interface circuit techniques

Inter- and intra-chip connections have become the new challenge to enable the scaling of computing systems, ranging from mobile devices to high-end servers. Demand for aggregate I/O bandwidth has been driven by applications including high-speed ethernet, backplane micro-servers, memory, graphics, chip-to-chip and network onchip. I/O circuitry is becoming the major power consumer in SoC processors and memories as the increasing bandwidth demands larger per-pin data rate or larger I/O pin count per component. The aggregate I/O bandwidth has approximately doubled every three to four years across a diverse range of standards in different applications. However, in order to keep pace with these standards enabled in part by process-technology scaling, we will require more than just device scaling in the near future. New energy-efficient circuit techniques must be proposed to enable the next generations of handheld and high-performance computers, given the thermal and system-power limits they start facing. ^ In this work, we are proposing circuit architectures that improve energy efficiency without decreasing speed performance for the most power hungry circuits in high speed interfaces. By the introduction of a new kind of logic operators in CMOS, called implication operators, we implemented a new family of high-speed frequency dividers/prescalers with reduced footprint and power consumption. New techniques and circuits for clock distribution, for pre-emphasis and for driver at the transmitter side of the I/O circuitry have been proposed and implemented. At the receiver side, new DFE architecture and CDR have been proposed and have been proven experimentally

Design Automation and Application for Emerging Reconfigurable Nanotechnologies

In the last few decades, two major phenomena have revolutionized the electronic industry – the ever-increasing dependence on electronic circuits and the Complementary Metal Oxide Semiconductor (CMOS) downscaling. These two phenomena have been complementing each other in a way that while electronics, in general, have demanded more computations per functional unit, CMOS downscaling has aptly supported such needs. However, while the computational demand is still rising exponentially, CMOS downscaling is reaching its physical limits. Hence, the need to explore viable emerging nanotechnologies is more imperative than ever. This thesis focuses on streamlining the existing design automation techniques for a class of emerging reconfigurable nanotechnologies. Transistors based on this technology exhibit duality in conduction, i.e. they can be configured dynamically either as a p-type or an n-type device on the application of an external bias. Owing to this dynamic reconfiguration, these transistors are also referred to as Reconfigurable Field-Effect Transistors (RFETs). Exploring and developing new technologies just like CMOS, require tackling two main challenges – first, design automation flow has to be modified to enable tailor- made circuit designs. Second, possible application opportunities should be explored where such technologies can outsmart the existing CMOS technologies. This thesis targets the above two objectives for emerging reconfigurable nanotechnologies by proposing approaches for enabling an Electronic Design Automation (EDA) flow for circuits based on RFETs and exploring hardware security as an application that exploits the transistor-level dynamic reconfiguration offered by this technology. This thesis explains the bottom-up approach adopted to propose a logic synthesis flow by identifying new logic gates and circuit design paradigms that can particularly exploit the dynamic reconfiguration offered by these novel nanotechnologies. This led to the subsequent need of finding natural Boolean logic abstraction for emerging reconfigurable nanotechnologies as it is shown that the existing abstraction of negative unate logic for CMOS technologies is sub-optimal for RFETs-based circuits. In this direction, it has been shown that duality in Boolean logic is a natural abstraction for this technology and can truly represent the duality in conduction offered by individual transistors. Finding this abstraction paved the way for defining suitable primitives and proposing various algorithms for logic synthesis and technology mapping. The following step is to explore compatible physical synthesis flow for emerging reconfigurable nanotechnologies. Using silicon nanowire-based RFETs, .lef and .lib files have been provided which can provide an end-to-end flow to generate .GDSII file for circuits exclusively based on RFETs. Additionally, new approaches have been explored to improve placement and routing for circuits based on reconfigurable nanotechnologies. It has been demonstrated how these approaches led to superior results as compared to the native flow meant for CMOS. Lastly, the unique property of transistor-level reconfiguration offered by RFETs is utilized to implement efficient Intellectual Property (IP) protection schemes against adversarial attacks. The ability to control the conduction of individual transistors can be argued as one of the impactful features of this technology and suitably fits into the paradigm of security measures. Prior security schemes based on CMOS technology often come with large overheads in terms of area, power, and delay. In contrast, RFETs-based hardware security measures such as logic locking, split manufacturing, etc. proposed in this thesis, demonstrate affordable security solutions with low overheads. Overall, this thesis lays a strong foundation for the two main objectives – design automation, and hardware security as an application, to push emerging reconfigurable nanotechnologies for commercial integration. Additionally, contributions done in this thesis are made available under open-source licenses so as to foster new research directions and collaborations.:Abstract List of Figures List of Tables 1 Introduction 1.1 What are emerging reconfigurable nanotechnologies? 1.2 Why does this technology look so promising? 1.3 Electronics Design Automation 1.4 The game of see-saw: key challenges vs benefits for emerging reconfigurable nanotechnologies 1.4.1 Abstracting ambipolarity in logic gate designs 1.4.2 Enabling electronic design automation for RFETs 1.4.3 Enhanced functionality: a suitable fit for hardware security applications 1.5 Research questions 1.6 Entire RFET-centric EDA Flow 1.7 Key Contributions and Thesis Organization 2 Preliminaries 2.1 Reconfigurable Nanotechnology 2.1.1 1D devices 2.1.2 2D devices 2.1.3 Factors favoring circuit-flexibility 2.2 Feasibility aspects of RFET technology 2.3 Logic Synthesis Preliminaries 2.3.1 Circuit Model 2.3.2 Boolean Algebra 2.3.3 Monotone Function and the property of Unateness 2.3.4 Logic Representations 3 Exploring Circuit Design Topologies for RFETs 3.1 Contributions 3.2 Organization 3.3 Related Works 3.4 Exploring design topologies for combinational circuits: functionality-enhanced logic gates 3.4.1 List of Combinational Functionality-Enhanced Logic Gates based on RFETs 3.4.2 Estimation of gate delay using the logical effort theory 3.5 Invariable design of Inverters 3.6 Sequential Circuits 3.6.1 Dual edge-triggered TSPC-based D-flip flop 3.6.2 Exploiting RFET’s ambipolarity for metastability 3.7 Evaluations 3.7.1 Evaluation of combinational logic gates 3.7.2 Novel design of 1-bit ALU 3.7.3 Comparison of the sequential circuit with an equivalent CMOS-based design 3.8 Concluding remarks 4 Standard Cells and Technology Mapping 4.1 Contributions 4.2 Organization 4.3 Related Work 4.4 Standard cells based on RFETs 4.4.1 Interchangeable Pull-Up and Pull-Down Networks 4.4.2 Reconfigurable Truth-Table 4.5 Distilling standard cells 4.6 HOF-based Technology Mapping Flow for RFETs-based circuits 4.6.1 Area adjustments through inverter sharings 4.6.2 Technology Mapping Flow 4.6.3 Realizing Parameters For The Generic Library 4.6.4 Defining RFETs-based Genlib for HOF-based mapping 4.7 Experiments 4.7.1 Experiment 1: Distilling standard-cells from a benchmark suite 4.7.2 Experiment 2A: HOF-based mapping . 4.7.3 Experiment 2B: Using the distilled standard-cells during mapping 4.8 Concluding Remarks 5 Logic Synthesis with XOR-Majority Graphs 5.1 Contributions 5.2 Organization 5.3 Motivation 5.4 Background and Preliminaries 5.4.1 Terminologies 5.4.2 Self-duality in NPN classes 5.4.3 Majority logic synthesis 5.4.4 Earlier work on XMG 5.4.5 Classification of Boolean functions 5.5 Preserving Self-Duality 5.5.1 During logic synthesis 5.5.2 During versatile technology mapping 5.6 Advanced Logic synthesis techniques 5.6.1 XMG resubstitution 5.6.2 Exact XMG rewriting 5.7 Logic representation-agnostic Mapping 5.7.1 Versatile Mapper 5.7.2 Support of supergates 5.8 Creating Self-dual Benchmarks 5.9 Experiments 5.9.1 XMG-based Flow 5.9.2 Experimental Setup 5.9.3 Synthetic self-dual benchmarks 5.9.4 Cryptographic benchmark suite 5.10 Concluding remarks and future research directions 6 Physical synthesis flow and liberty generation 6.1 Contributions 6.2 Organization 6.3 Background and Related Work 6.3.1 Related Works 6.3.2 Motivation 6.4 Silicon Nanowire Reconfigurable Transistors 6.5 Layouts for Logic Gates 6.5.1 Layouts for Static Functional Logic Gates 6.5.2 Layout for Reconfigurable Logic Gate 6.6 Table Model for Silicon Nanowire RFETs 6.7 Exploring Approaches for Physical Synthesis 6.7.1 Using the Standard Place & Route Flow 6.7.2 Open-source Flow 6.7.3 Concept of Driver Cells 6.7.4 Native Approach 6.7.5 Island-based Approach 6.7.6 Utilization Factor 6.7.7 Placement of the Island on the Chip 6.8 Experiments 6.8.1 Preliminary comparison with CMOS technology 6.8.2 Evaluating different physical synthesis approaches 6.9 Results and discussions 6.9.1 Parameters Which Affect The Area 6.9.2 Use of Germanium Nanowires Channels 6.10 Concluding Remarks 7 Polymporphic Primitives for Hardware Security 7.1 Contributions 7.2 Organization 7.3 The Shift To Explore Emerging Technologies For Security 7.4 Background 7.4.1 IP protection schemes 7.4.2 Preliminaries 7.5 Security Promises 7.5.1 RFETs for logic locking (transistor-level locking) 7.5.2 RFETs for split manufacturing 7.6 Security Vulnerabilities 7.6.1 Realization of short-circuit and open-circuit scenarios in an RFET-based inverter 7.6.2 Circuit evaluation on sub-circuits 7.6.3 Reliability concerns: A consequence of short-circuit scenario 7.6.4 Implication of the proposed security vulnerability 7.7 Analytical Evaluation 7.7.1 Investigating the security promises 7.7.2 Investigating the security vulnerabilities 7.8 Concluding remarks and future research directions 8 Conclusion 8.1 Concluding Remarks 8.2 Directions for Future Work Appendices A Distilling standard-cells B RFETs-based Genlib C Layout Extraction File (.lef) for Silicon Nanowire-based RFET D Liberty (.lib) file for Silicon Nanowire-based RFET

6T-SRAM 1Mb Design with Test Structures and Post Silicon Validation

abstract: Static random-access memories (SRAM) are integral part of design systems as caches and data memories that and occupy one-third of design space. The work presents an embedded low power SRAM on a triple well process that allows body-biasing control. In addition to the normal mode operation, the design is embedded with Physical Unclonable Function (PUF) [Suh07] and Sense Amplifier Test (SA Test) mode. With PUF mode structures, the fabrication and environmental mismatches in bit cells are used to generate unique identification bits. These bits are fixed and known as preferred state of an SRAM bit cell. The direct access test structure is a measurement unit for offset voltage analysis of sense amplifiers. These designs are manufactured using a foundry bulk CMOS 55 nm low-power (LP) process. The details about SRAM bit-cell and peripheral circuit design is discussed in detail, for certain cases the circuit simulation analysis is performed with random variations embedded in SPICE models. Further, post-silicon testing results are discussed for normal operation of SRAMs and the special test modes. The silicon and circuit simulation results for various tests are presented.Dissertation/ThesisMasters Thesis Electrical Engineering 201

A high speed serializer/deserializer design

A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design. A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption. A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset). With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage. A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit. The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications

Design of low-voltage power efficient frequency dividers in folded MOS current mode logic

In this paper we propose a methodology to design high-speed, power-efficient static frequency dividers based on the low-voltage Folded MOS Current Mode Logic (FMCML) approach. A modeling strategy to analyze the dependence of propagation delay and power consumption on the bias currents of the divide-by-2 (DIV2) cell is introduced. We demonstrate that the behavior of the FMCML DIV2 cell is different both from the one of the conventional MCML DFF (D-type Flip-Flop) and from FMCML DFF without a level shifter. Then an analytical strategy to optimize the divider in different design scenarios: maximum speed, minimum power-delay product (PDP) or minimum energy-delay product (EDP) is presented. The possibility to scale the bias currents through the divider stages without affecting the speed performance is also investigated. The proposed analytical approach allows to gain a deep insight into the circuit behavior and to comprehensively optimize the different design tradeoffs. The derived models and design guidelines are validated against transistor level simulations referring to a commercial 28nm FDSOI CMOS process. Different divide-by-8 circuits following different optimization strategies have been designed in the same 28nm CMOS technology showing the effectiveness of the proposed methodology

Integration of behavioral and layout synthesis : a chip synthesis approach

Chip synthesis deals with the transformation of a behavioral description into a fabricated chip. Typically, chip synthesis is carried out in three stages: behavioral, logic/sequential and layout synthesis. Since chip synthesis involves a multi-level synthesis task, integration and coordination of tasks for all levels of synthesis is the essential issue.This dissertation addresses a chip synthesis paradigm and describes the key issues with regard to the integration of behavioral and layout synthesis for chip design. In order to successfully integrate all tasks in the chip synthesis process, a finite-state machine with a datapath (FSMD) design model and a sliced-layout architecture have been developed for chip synthesis. Using the sliced-layout architecture, a partitioning-based layout synthesis method and system have been developed to synthesize layout from generalized register-transfer (RT) netlists. In addition, based on the FSMD and the sliced-layout architecture, area and timing models are developed for behavioral synthesis. To incorporate layout information into behavioral synthesis, a unified representation is developed for behavioral synthesis. Using the unified representation and layout model, a layout-driven unit-binding approach is presented. Several sets of experiments were performed to validate the proposed approaches including the layout-synthesis method, the layout model and the layout-driven unit-binding task

A sub-threshold cell library and methodology

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2006.Includes bibliographical references (p. 97-102).Sub-threshold operation is a compelling approach for energy-constrained applications where speed is of secondary concern, but increased sensitivity to process variation must be mitigated in this regime. With scaling of process technologies, random within-die variation has recently introduced another degree of complexity in circuit design. This thesis proposes approaches to mitigate process variation in sub-threshold circuits through device sizing, topology selection and fault-tolerant architecture. This thesis makes several contributions to a sub-threshold circuit design methodology. A formal analysis of device sizing trade-offs between delay, energy, and variability reveals that while minimum size devices provide lowest energy and delay in sub-threshold, their increased sensitivity to random dopant fluctuation may cause functional errors. A proposed variation-driven design approach enables consistent sizing of logic gates and registers for constant functional yield. A yield constraint imposes energy overhead at low power supply voltages and changes the minimum energy operating point of a circuit.(cont.) The optimal supply and device sizing depend on the topology of the circuit and its energy versus VDD characteristic. The analysis resulted in a 56-cell library in 65nm CMOS, which is incorporated in a computer-aided design flow. A test chip synthesized from this library implements a fault-tolerant FIR filter. Algorithmic error detection enables correction of transient timing errors due to delay variability in sub-threshold, and also allows the system frequency to be set more aggressively for the average case instead of the worst case.by Joyce Y.S. Kwong.S.M

The development and performance evaluation of PIF logic functional blocks

In the deep submicron range of integrated circuit design, interconnects and not the logical gates are causing the performance bottleneck. The number of available transistors increase by a factor of 2 every technology node but interconnects do not scale with devices, devices scale down faster and thus the present designs need to be scalable and reusable. Pipeline interconnect free (PIF) logic methodology has a potential to solve these current design problems. In PIF logic methodology the global interconnects are replaced by a chain of logical gates. PIF logic uses only one type of gate which can be connected only to the adjacent eight gates making the gate and the interconnect modeling easier. In order to migrate from one technology node to other, just one PIF cell needs to be redesigned. The PIF cell in new technology node can replace the present cells thus making PIF logic based circuits fully reusable. This thesis implements PIF design methodology to develop two libraries consisting of combinational and sequential functional blocks such as adder, shift registers, multiplexers, decoders and encoders. The performance of these functional blocks is compared with the standard cell implementation with respect to the quality metrics (power dissipation, propagation delay and layout area)

Radiation Hardened by Design Methodologies for Soft-Error Mitigated Digital Architectures

abstract: Digital architectures for data encryption, processing, clock synthesis, data transfer, etc. are susceptible to radiation induced soft errors due to charge collection in complementary metal oxide semiconductor (CMOS) integrated circuits (ICs). Radiation hardening by design (RHBD) techniques such as double modular redundancy (DMR) and triple modular redundancy (TMR) are used for error detection and correction respectively in such architectures. Multiple node charge collection (MNCC) causes domain crossing errors (DCE) which can render the redundancy ineffectual. This dissertation describes techniques to ensure DCE mitigation with statistical confidence for various designs. Both sequential and combinatorial logic are separated using these custom and computer aided design (CAD) methodologies. Radiation vulnerability and design overhead are studied on VLSI sub-systems including an advanced encryption standard (AES) which is DCE mitigated using module level coarse separation on a 90-nm process with 99.999% DCE mitigation. A radiation hardened microprocessor (HERMES2) is implemented in both 90-nm and 55-nm technologies with an interleaved separation methodology with 99.99% DCE mitigation while achieving 4.9% increased cell density, 28.5 % reduced routing and 5.6% reduced power dissipation over the module fences implementation. A DMR register-file (RF) is implemented in 55 nm process and used in the HERMES2 microprocessor. The RF array custom design and the decoders APR designed are explored with a focus on design cycle time. Quality of results (QOR) is studied from power, performance, area and reliability (PPAR) perspective to ascertain the improvement over other design techniques. A radiation hardened all-digital multiplying pulsed digital delay line (DDL) is designed for double data rate (DDR2/3) applications for data eye centering during high speed off-chip data transfer. The effect of noise, radiation particle strikes and statistical variation on the designed DDL are studied in detail. The design achieves the best in class 22.4 ps peak-to-peak jitter, 100-850 MHz range at 14 pJ/cycle energy consumption. Vulnerability of the non-hardened design is characterized and portions of the redundant DDL are separated in custom and auto-place and route (APR). Thus, a range of designs for mission critical applications are implemented using methodologies proposed in this work and their potential PPAR benefits explored in detail.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201