159 research outputs found
Compact thermal models of semiconductor devices â a review
In the paper the problem of modelling thermal properties of semiconductor devices with the use of compact models is presented. This class of models is defined and their development over the past dozens of years is described. Possibilities of modelling thermal phenomena both in discrete semiconductor devices, monolithic integrated circuits, power modules and selected electronic circuits are presented. The problem of the usefulness range of compact thermal models in the analysis of electronic elements and circuits is discussed on the basis of investigations performed in Gdynia Maritime University
Microstructure Influence of SACX0307-TiO2 Composite Solder Joints on Thermal Properties of Power LED Assemblies
The effect of the microstructure of solder joints on the thermal properties of power LEDs was investigated. Solder joints were prepared with different solder pastes, namely 99Sn0.3Ag0.7Cu (as reference solder) and reinforced 99Sn0.3Ag0.7Cu-TiO2 (composite solder). TiO2 ceramic was used at 1 wt% and with two different primary particle sizes, which were 20nm (nano) and 200nm (submicron). The thermal resistance, the electric thermal resistance, and the luminous efficiency of the power LED assemblies were measured. Furthermore, the microstructure of the different solder joints was analyzed on the basis of cross-sections using scanning electron and optical microscopy. It was found that the addition of submicron TiO2 decreased the thermal and electric thermal resistances of the light sources by 20% and 16%, respectively, and it slightly increased the luminous efficiency. Microstructural evaluations showed that the TiO2 particles were incorporated at the Sn grain boundaries and at the interface of the intermetallic layer and the solder bulk. This caused considerable refinement of the Sn grain structure. The precipitated TiO2 particles at the bottom of the solder joint changed the thermodynamics of Cu6Sn5 formation and enhanced the spalling of intermetallic grain to solder bulk, which resulted in a general decrease in the thickness of the intermetallic layer. These phenomena improved the heat paths in the composite solder joints, and resulted in better thermal and electrical properties of power LED assemblies. However, the TiO2 nanoparticles could also cause considerable local IMC growth, which could inhibit thermal and electrical improvements
Determining the wavelength dependancy of the optical properties of the glacial ice using in-situ light sources.
Neutrinos are unique cosmic messengers, their weak interactions and lack of electric charge means they can travel from cosmic distances, without absorption or deflection. IceCube is a neutrino observatory constructed at depths of 1450-2450 m below the surface at the South Pole. The main objective of IceCube is to detect astrophysical neutrinos to enable a better understanding of high-energy cosmic rays including their production mechanism and also their origins.
IceCube observes neutrinos through detecting the light emitted by the products of neu- trino interactions. Characterisation of the optical properties of the glacial ice is necessary for the physical parameters of the neutrinos, such as their energies and directions, to be determined from the pattern and timing of the light detected. Embedded LEDs within the deployed modules enable the generation of in-situ light with five different wavelengths. This light can be detected by the detector array and used to determine the optical properties of the instrumented ice.
The main focus of this thesis was to investigate and parameterise the wavelength de- pendence of the absorption and scattering coeffi cients of the ice. The values found for the parameters characterising this wavelength dependence were consistent with previous mea- surements although slightly different values were obtained. While the new parameters are considered to be more robust than past measurements due to improved knowledge of the light emitters, it is recommended that this study is revisited when the observed anisotropic light propagation has been further modelled.
In addition to the main study into the wavelength dependence of the optical properties of the ice, investigations were also undertaken to characterise properties of the optical modules such as their orientation.
Calibration tools developed and used in this thesis will be of use when the IceCube upgrade devices are deployed, allowing our knowledge and characterisation of the ice to be improved significantly
High-precision optical scanning in the near and far field
This dissertation addresses one of the tools used for measuring the properties of light in optical devices. This instrument can locally probe the light to assess its phase and amplitude at precise locations, providing critical information. The primary focus of this work is to enhance the height feedback for the probe's positioning, develop a procedure for the simultaneous measurement of orthogonal polarizations in free-space beams, and formulate an algorithm for the polarization-resolved assessment of guided modes in a bus waveguide-ring resonator system
Recommended from our members
Novel Computing Paradigms using Oscillators
This dissertation is concerned with new ways of using oscillators to perform computational tasks. Specifically, it introduces methods for building finite state machines (for general-purpose Boolean computation) as well as Ising machines (for solving combinatorial optimization problems) using coupled oscillator networks.But firstly, why oscillators? Why use them for computation?An important reason is simply that oscillators are fascinating. Coupled oscillator systems often display intriguing synchronization phenomena where spontaneous patterns arise. From the synchronous flashing of fireflies to Huygens' clocks ticking in unison, from the molecular mechanism of circadian rhythms to the phase patterns in oscillatory neural circuits, the observation and study of synchronization in coupled oscillators has a long and rich history. Engineers across many disciplines have also taken inspiration from these phenomena, e.g., to design high-performance radio frequency communication circuits and optical lasers. To be able to contribute to the study of coupled oscillators and leverage them in novel paradigms of computing is without question an interesting andfulfilling quest in and of itself.Moreover, as Moore's Law nears its limits, new computing paradigms that are different from mere conventional complementary metalâoxideâsemiconductor (CMOS) scaling have become an important area of exploration. One broad direction aims to improve CMOS performance using device technology such as fin field-effect transistors (FinFET) and gate-all-around (GAA) FETs. Other new computing schemes are based on non-CMOS material and device technology, e.g., graphene, carbon nanotubes, memristive devices, optical devices, etc.. Another growing trend in both academia and industry is to build digital application-specific integrated circuits (ASIC) suitable for speeding up certain computational tasks, often leveraging the parallel nature of unconventional non-von Neumann architectures. These schemes seek to circumvent the limitations posed at the device level through innovations at the system/architecture level.Our work on oscillator-based computation represents a direction that is different from the above and features several points of novelty and attractiveness. Firstly, it makes meaningful use of nonlinear dynamical phenomena to tackle well-defined computational tasks that span analog and digital domains. It also differs from conventional computational systems at the fundamental logic encoding level, using timing/phase of oscillation as opposed to voltage levels to represent logic values. These differences bring about several advantages. The change of logic encoding scheme has several device- and system-level benefits related to noise immunity and interference resistance. The use of nonlinear oscillator dynamics allows our systems to address problems difficult for conventional digital computation. Furthermore, our schemes are amenable to realizations using almost all types of oscillators, allowing a wide variety of devices from multiple physical domains to serve as the substrate for computing. This ability to leverage emerging multiphysics devices need not put off the realization of our ideas far into the future. Instead, implementations using well-established circuit technology are already both practical and attractive.This work also differs from all past work on oscillator-based computing, which mostly focuses on specialized image preprocessing tasks, such as edge detection, image segmentation and pattern recognition. Perhaps its most unique feature is that our systems use transitions between analog and digital modes of operation --- unlike other existing schemes that simply couple oscillators and let their phases settle to a continuum of values, we use a special type of injection locking to make each oscillator settle to one of the several well-defined multistable phase-locked states, which we use to encode logic values for computation. Our schemes of oscillator-based Boolean and Ising computation are built upon this digitization of phase; they expand the scope of oscillator-based computing significantly.Our ideas are built on years of past research in the modelling, simulation and analysis of oscillators. While there is a considerable amount of literature (arguably since Christiaan Huygens wrote about his observation of synchronized pendulum clocks in the 17th century) analyzing the synchronization phenomenon from different perspectives at different levels, we have been able to further develop the theory of injection locking, connecting the dots to find a path of analysis that starts from the low-level differential equations of individual oscillators and arrives at phase-based models and energy landscapes of coupled oscillator systems. This theoretical scaffolding is able not only to explain the operation of oscillator-based systems, but also to serve as the basis for simulation and design tools. Building on this, we explore the practical design of our proposed systems, demonstrate working prototypes, as well as develop the techniques, tools and methodologies essential for the process
Physics-based simulation of narrow and wide band gap photonic devices
Historically, infrared (IR) detector technologies are connected mainly with controlling and night-vision problems: in a first stage, applications concerned simply with detection of IR radiation, but very soon capabilities to form IR images were developed, opening the way to systems for recognition and surveillance, especially for military purposes. Since the last decade of the twentieth century, the use of IR imaging systems for civil and peaceful purposes have increased continuously: these include medical and industrial applications, detection of earth resources, earth and universe sciences, etc. As an example, IR imaging is widely used in astronomy, to study interstellar medium and first-stages of stellar evolution; in medicine, IR thermography â IR imaging of the human body â is employed to detect cancers or other trauma; IR detectors are also widely used in automotive industry, chemical process monitoring, global monitoring of environmental pollution and climate changes, etc. The discovery in 1959 by Lawson and co-workers of the wide tunability of the HgCdTe alloy allowed this compound to become one of the most important and versatile materials for detector applications over the entire IR range. A critical contribution to research is given by Technology Computer-Aided Design (TCAD), modeling and simulation. In the first part of this thesis, I present the main part of my research activity, focused on the development of abilities and methodologies for the simulation of realistic three-dimensional HgCdTe-based infrared photodetectors. The purpose is the investigation of generation-recombination (GR) mechanisms and modeling of spectral photoresponse in narrow-gap HgCdTe-based photodetectors, with one-, two and three-dimensional (1D, 2D, 3D) realistic TCAD models (Chapters 1-5).
Another important topic of industrial research in semiconductor physics deals with nitride-based light-emitting diodes (LEDs). From automotive to streetlights, from lights in our houses to the displays of TVs and smartphones, LED-based technology is making its way in the market. This proliferation would have been impossible without GaN-based LEDs, whose invention by Isamu Akasaki, Hiroshi Amano and Shuji Nakamura has been rewarded with the 2014 Nobel Prize in Physics. Nevertheless, GaN-based LEDs performanceis limited by a reduction (droop) of their internal quantum efficiency (IQE) as the driving current density is increased beyond 10 A/cm2, whose physical origin is still under intense debate. In the second part of this thesis, I present a quantum model, based on condensed matter many-body theory, that allowed to obtain the electron capture time and hot-electron intraband relaxation times in a quantum well (QW)-barrier heterostructure, for longitudinal optic (LO) phonon emission, as function of carrier density. The interaction was described in the Single Plasmon Pole of the Random Phase Approximation, retaining the full density-, energy- and wavevector-dependent form of the dielectric function (Chapters 6-7)
Memristors
This Edited Volume Memristors - Circuits and Applications of Memristor Devices is a collection of reviewed and relevant research chapters, offering a comprehensive overview of recent developments in the field of Engineering. The book comprises single chapters authored by various researchers and edited by an expert active in the physical sciences, engineering, and technology research areas. All chapters are complete in itself but united under a common research study topic. This publication aims at providing a thorough overview of the latest research efforts by international authors on physical sciences, engineering, and technology,and open new possible research paths for further novel developments
- âŠ