A Low Temperature Co-fired Ceramic (LTCC) Interposer Based Three-Dimensional Stacked Wire Bondless Power Module

The objective of this dissertation research is to develop a low temperature co-fired ceramic (LTCC) interposer-based module-level 3-D wire bondless stacked power module. As part of the dissertation work, the 3-D wire bondless stack is designed, simulated, fabricated and characterized. The 3-D wire bondless stack is realized with two stand-alone power modules in a half-bridge configuration. Each stand-alone power module consists of two 1200 V 25 A silicon insulated-gate bipolar transistor (IGBT) devices in parallel and two 1200 V 20 A Schottky barrier diodes (SBD) in an antiparallel configuration. A novel interconnection scheme with conductive clamps and a spring loaded LTCC interposer is introduced to establish electrical connection between the stand-alone power modules to connect them in series to realize a half-bridge stack. Process development to fabricate the LTCC based 3-D stack is performed. In traditional power modules, wire bonds are used as a top side interconnections that introduce additional parasitic inductance in the current conduction path and prone to failure mechanism under high thermomechanical stresses. The loop inductance of the proposed 3-D half-bridge module exhibits 71% lower parasitic inductance compared to a wire bonded module. The 3-D stack exhibits better switching performance compared to the wire bonded counterpart. The measurement results for the 3-D stack shows 30% decrease in current overshoot at turn-on and 43% voltage overshoot at turn-off compared to the wire bonded module. Through measurements, it has been shown that the conducted noise reduces by 20 dB in the frequency range 20-30 MHz for the 3-D stack compared to the wire bonded counterpart. A simulation methodology using co-simulation techniques using ANSYS EM software tools is developed to predict EMI of a power module. Hardware verification of the proposed simulation methodology is performed to validate the co-simulation technique. The correlation coefficient between the measurement and simulation is found to be 0.73. It is shown that 53% of the variability in the simulation can be explained by the simulated result. Moreover, the simulated and measured amplitudes of the EMI spectrum closely match with each other with some variations due to round-off errors due to the FFT conversion

The Adaptive Gain Integrating Pixel Detector at the European XFEL

The Adaptive Gain Integrating Pixel Detector (AGIPD) is an x-ray imager, custom designed for the European x-ray Free-Electron Laser (XFEL). It is a fast, low noise integrating detector, with an adaptive gain amplifier per pixel. This has an equivalent noise of less than 1 keV when detecting single photons and, when switched into another gain state, a dynamic range of more than 10$^4$ photons of 12 keV. In burst mode the system is able to store 352 images while running at up to 6.5 MHz, which is compatible with the 4.5 MHz frame rate at the European XFEL. The AGIPD system was installed and commissioned in August 2017, and successfully used for the first experiments at the Single Particles, Clusters and Biomolecules (SPB) experimental station at the European XFEL since September 2017. This paper describes the principal components and performance parameters of the system.Comment: revised version after peer revie

A DLL Based Test Solution for 3D ICs

Integrated circuits (ICs) are rapidly changing and vertical integration and packaging strategies have already become an important research topic. 2.5D and 3D IC integrations have obvious advantages over the conventional two dimensional IC implementations in performance, capacity, and power consumption. A passive Si interposer utilizing Through-Silicon via (TSV) technology is used for 2.5D IC integration. TSV is also the enabling technology for 3D IC integration. TSV manufacturing defects can affect the performance of stacked devices and reduce the yield. Manufacturing test methodologies for TSVs have to be developed to ensure fault-free devices. This thesis presents two test methods for TSVs in 2.5D and 3D ICs utilizing Delay-Locked Loop (DLL) modules. In the test method developed for TSVs in 2.5D ICs, a DLL is used to determine the propagation delay for fault detection. TSV faults in 3D ICs are detected through observation of the control voltage of a DLL. The proposed test methods present a robust performance against Process, supply Voltage and Temperature (PVT) variations due to the inherent feedback of DLLs. 3D full-wave simulations are performed to extract circuit level models for TSVs and fragments of an interposer wires using HFSS simulation tools. The extracted TSV models are then used to perform circuit level simulations using ADS tools from Agilent. Simulation results indicate that the proposed test solution for TSVs can detect manufacturing defects affecting the TSV propagation delay

Through-Silicon Vias in SiGe BiCMOS and Interposer Technologies for Sub-THz Applications

Im Rahmen der vorliegenden Dissertation zum Thema „Through-Silicon Vias in SiGe BiCMOS and Interposer Technologies for Sub-THz Applications“ wurde auf Basis einer 130 nm SiGe BiCMOS Technologie ein Through-Silicon Via (TSV) Technologiemodul zur Herstellung elektrischer Durchkontaktierungen für die Anwendung im Millimeterwellen und Sub-THz Frequenzbereich entwickelt. TSVs wurden mittels elektromagnetischer Simulationen modelliert und in Bezug auf ihre elektrischen Eigenschaften bis in den sub-THz Bereich bis zu 300 GHz optimiert. Es wurden die Wechselwirkungen zwischen Modellierung, Fertigungstechnologie und den elektrischen Eigenschaften untersucht. Besonderes Augenmerk wurde auf die technologischen Einflussfaktoren gelegt. Daraus schlussfolgernd wurde das TSV Technologiemodul entwickelt und in eine SiGe BiCMOS Technologie integriert. Hierzu wurde eine Via-Middle Integration gewählt, welche eine Freilegung der TSVs von der Wafer Rückseite erfordert. Durch die geringe Waferdicke von ca. 75 μm wird einen Carrier Wafer Handling Prozess verwendet. Dieser Prozess wurde unter der Randbedingung entwickelt, dass eine nachfolgende Bearbeitung der Wafer innerhalb der BiCMOS Pilotlinie erfolgen kann. Die Rückseitenbearbeitung zielt darauf ab, einen Redistribution Layer auf der Rückseite der BiCMOS Wafer zu realisieren. Hierzu wurde ein Prozess entwickelt, um gleichzeitig verschiedene TSV Strukturen mit variablen Geometrien zu realisieren und damit eine hohe TSV Design Flexibilität zu gewährleisten. Die TSV Strukturen wurden von DC bis über 300 GHz charakterisiert und die elektrischen Eigenschaften extrahiert. Dabei wurde gezeigt, dass TSV Verbindungen mit sehr geringer Dämpfung <1 dB bis 300 GHz realisierbar sind und somit ausgezeichnete Hochfrequenzeigenschaften aufweisen. Zuletzt wurden vielfältige Anwendungen wie das Grounding von Hochfrequenzschaltkreisen, Interposer mit Waveguides und 300 GHz Antennen dargestellt. Das Potential für Millimeterwellen Packaging und 3D Integration wurde evaluiert. TSV Technologien sind heutzutage in vielen Anwendungen z.B. im Bereich der Systemintegration von Digitalschaltkreisen und der Spannungsversorgung von integrierten Schaltkreisen etabliert. Im Rahmen dieser Arbeit wurde der Einsatz von TSVs für Millimeterwellen und dem sub-THz Frequenzbereich untersucht und die Anwendung für den sub-THz Bereich bis 300 GHz demonstriert. Dadurch werden neue Möglichkeiten der Systemintegration und des Packaging von Höchstfrequenzsystemen geschaffen.:Bibliographische Beschreibung List of symbols and abbreviations Acknowledgement 1. Introduction 2. FEM Modeling of BiCMOS & Interposer Through-Silicon Vias 3. Fabrication of BiCMOS & Silicon Interposer with TSVs 4. Characterization of BiCMOS Embedded Through-Silicon Vias 5. Applications 6. Conclusion and Future Work 7. Appendix 8. Publications & Patents 9. Bibliography 10. List of Figures and Table

Integrated silicon photonic packaging

Silicon photonics has garnered plenty of interests from both the academia and industry due to its high-speed transmission potential as well as sensing capability to complement silicon electronics. This has led to significant growth on the former, valuing at US$626.8M in 2017 and is expected to grow 3-fold to US$ 1,988.2M by 2023, based on data from MarketsandMarkets™. Silicon photonics’ huge potential has led to worldwide attention on fundamental research, photonic circuit designs and device fabrication technologies. However, as with silicon electronics in its early years, the silicon photonics industry today is extremely fragmented with various chip designs and layouts. Most silicon photonic devices fabricated are not able to reach the hand of consumers, due to a lack of information related to packaging design rules, components and processes. The importance of packaging technologies, which play a crucial role in turning photonic circuits and devices into the final product that end users can used in their daily lives, has been overlooked and understudied. This thesis aims to – 1. fill the missing gap by adapting existing electronics packaging techniques, 2. assess its scalability, 3. assess supply chain integration and finally 4. develop unique packaging approaches specifically for silicon photonics. The first section focused on high density packaging components and processes using University of California, Berkeley’s state-of-the-art silicon photonic MEMS optical switches as test devices. Three test vehicles were developed using (1) via-less ceramic and (2) spring-contacted electrical interposers for 2D integration and (3) through-glass-via electrical interposers for 2.5D heterogeneous integration. A high density (1) lidless fibre array and (2) a 2D optical interposer, which allows pitch-reduction of optical waveguides were also developed in this thesis. Together, these components demonstrated the world’s first silicon 2 photonic MEMS optical switch package and subsequently the highest density silicon photonic packaging components with 512 electrical I/Os and 272 optical I/Os. The second section then moved away from active optical coupling that was used in the former, investigating instead passive optical packaging concepts for the future. Two approaches were investigated - (1) grating-to-grating and (2) evanescent couplings. The former allows the development of pluggable packages, separating fibre coupling away from the device while the latter allows simultaneous optical and electrical packaging on a glass wafer in a single process. Lastly, the knowhow and concepts developed in this thesis were compiled into packaging design rules and subsequently introduced into H2020-MORPHIC, PIXAPP packaging training courses (as a trainer) and other packaging projects within the group