Maximally flat and least-square co-design of variable fractional delay filters for wideband software-defined radio

This paper describes improvements in a Farrow-structured variable fractional delay (FD) Lagrange filter for all-pass FD interpolation. The main idea is to integrate the truncated sinc into the Farrow structure of a Lagrange filter, in order that a superior FD approximation in the least-square sense can be achieved. Its primary advantages are the lower level of mean-square-error (MSE) over the whole FD range and the reduced implementation cost. Extra design parameters are introduced for making the trade-off between MSE and maximal flatness under different design requirements. Design examples are included, illustrating an MSE reduction of 50% compared to a classical Farrow-structured Lagrange interpolator while the implementation cost is reduced. This improved variable FD interpolation system is suitable for many applications, such as sample rate conversion, digital beamforming and timing synchronization in wideband software-defined radio (SDR) communications

The Design of an Anti-Aliasing Filter for the Next Generation Digitiser

MeerKAT, is a 64-element radio astronomy antenna array which has been recently constructed in the Northern Cape Province of South Africa. It serves as South Africa's contribution towards the international Square Kilometre Array (SKA) project. The MeerKAT array has been designed to observe radio signals produced by celestial sources at UHF-Band, L-Band, S-Band and X-Band frequencies. The first phase of the construction included the design, development and integration of the UHF-Band, L-Band and S-band Receivers, whilst the X-band design has been superseded by the incorporation of the next phase of the SKA international project. In preparation of the next the roll-out, research is required to determine optimal wideband filter topologies suitable for direct digitisation of signal frequencies over the frequency range of 3-6 GHz. In this thesis, exploration of suitable wideband planar filters is performed, noting those with an improved out-of-band rejection. The outcome of the investigation leads into the design and development of the suitable wideband planar filter based on key performance specifications. The performance of the manufactured wideband planar filter is then compared to the theoretical design, and validated against the key performance requirements

Digital Filters

The new technology advances provide that a great number of system signals can be easily measured with a low cost. The main problem is that usually only a fraction of the signal is useful for different purposes, for example maintenance, DVD-recorders, computers, electric/electronic circuits, econometric, optimization, etc. Digital filters are the most versatile, practical and effective methods for extracting the information necessary from the signal. They can be dynamic, so they can be automatically or manually adjusted to the external and internal conditions. Presented in this book are the most advanced digital filters including different case studies and the most relevant literature

Hardware emulation of wireless communication fading channels

This dissertation investigates several main challenges to implementing hardware-based wireless fading channel emulators with emphasis on incorporating accurate correlation properties. Multiple-input multiple-output (MIMO) fading channels are usually triply-selective with three types of correlation: temporal correlation, inter-tap correlation, and spatial correlation. The proposed emulators implement the triply-selective fading Channel Impulse Response (CIR) by incorporating the three types of correlation into multiple uncorrelated frequency-flat Rayleigh fading waveforms while meeting real-time requirements for high data-rate, large-sized MIMO, and/or long CIR channels. Specifically, mixed parallel-serial computational structures are implemented for Kronecker products of the correlation matrices, which makes the best tradeoff between computational speed and hardware usage. Five practical fading channel examples are implemented for RF or underwater acoustic MIMO applications. The performance of the hardware emulators are verified with an Altera Field-Programmable Gate Array (FPGA) platform and the results match the software simulators in terms of statistical and correlation properties. The dissertation also contributes to the development of a 2-by-2 MIMO transceiver testbench that is used to measure real-world fading channels. Intensive channel measurements are performed for indoor fixed mobile-to-mobile channels and the estimated CIRs demonstrate the triply-selective correlation properties --Abstract, page iv

Design, Modelling and Implementation of Several Multi-Standard High Performance Single-Wideband and Multi-Wideband Microwave Planar Filters

The objectives of this work are to review, investigate and model the microwave planar filters of the modern wireless communication system. The recent main stream of microwave filters are classified and discussed separately. Various microwave filters with detailed applications are investigated in terms of their geometrical structures and operational performances. A comprehensive theoretical study of microwave filters is presented. The main types of microwave filters including the basic low-pass filters such as Butterworth and Chebyshev filters are fully analysed and described in detail. The transformation from low-pass prototype filters to high-pass filters, band-pass filters and band-stop filters are illustrated and introduced. Research work on stepped impedance resonator (SIR) and asymmetric stepped impedance resonator (ASIR) structure is presented. The characteristics of λg/4, λg/2 and λg (λg is the guided wavelength of the fundamental frequency in the free space) type SIR resonators, and the characteristic of asymmetric SIR resonator are categorized and investigated. Based on the content mentioned above, novel multi-standard high performance asymmetric stepped impedance resonator single-wideband and dual-wideband filters with wide stopbands are proposed. The methodologies to realize wide passband and wide stop-band filters are detailed. In addition, multi-standard high performance triplewideband, quadruple-wideband and quint-wideband filters are suggested and studied. The measurement results for all prototype filters agree well with the theoretical predictions and simulated results from Ansoft HFSS software. The featured broad bandwidths over single/multiple applicable frequency bands and the high performances of the proposed filters make them very promising for applications in future multistandard wireless communication

Analysis and Design of Low-Cost Waveguide Filters for Wireless Communications

The area of research of this thesis is built around advanced waveguide filter structures. Waveguide filters and the waveguide technology in general are renowned for high power capacity, low losses and excellent electromagnetic shielding. Waveguide filters are important components in fixed wireless communications as well as in satellite and radar systems. Furthermore, their advantages and utilization become even greater with increase in frequency, which is a trend in modern communication systems because upper frequency bands offer larger channel capacities. However, waveguide filters are relatively bulky and expensive. To comply with more and more demanding miniaturization and cost-cutting requirements, compactness and economical design represent some of the main contemporary focuses of interest. Approaches that are used to achieve this include use of planar inserts to build waveguide discontinuities, additive manufacturing and substrate integration. At the same time, waveguide filters still need to satisfy opposed stringent requirements like small insertion loss, high selectivity and multiband operation. Another difficulty that metal waveguide components face is integration with other circuitry, especially important when solid-state active devices are included. Thus, improvements of interconnections between waveguide and other transmission interfaces are addressed too. The thesis elaborates the following aspects of work: Further analysis and improved explanations regarding advanced waveguide filters with E-plane inserts developed by the Wireless Communications Research Group, using both cross coupled resonators and extracted pole sections (Experiments with higher filter orders, use of tuning screws, degrees of freedom in design, etc. Thorough performance comparison with competing filter technologies) - Proposing novel E-plane filter sections with I-shaped insets - Extension of the E-plane filtering structures with metal fins to new compact dual band filters with high frequency selectivity and miniaturized diplexers. - Introduction of easy-to-build waveguide filters with polymer insert frames and high-performance low-profile cavity filters, taking advantage of enhanced fabrication capabilities when using additive manufacturing - Developing new substrate integrated filters, as well as circuits used to transfer signals between different interfaces Namely, these are substrate integrated waveguide to metal waveguide planar transitions that do not require any modifications of the metal waveguides. Such novel transitions have been designed both for single and orthogonal signal polarizations

ワイヤレス通信のための先進的な信号処理技術を用いた非線形補償法の研究

The inherit nonlinearity in analogue front-ends of transmitters and receivers have had primary impact on the overall performance of the wireless communication systems, as it gives arise of substantial distortion when transmitting and processing signals with such circuits. Therefore, the nonlinear compensation (linearization) techniques become essential to suppress the distortion to an acceptable extent in order to ensure sufficient low bit error rate. Furthermore, the increasing demands on higher data rate and ubiquitous interoperability between various multi-coverage protocols are two of the most important features of the contemporary communication system. The former demand pushes the communication system to use wider bandwidth and the latter one brings up severe coexistence problems. Having fully considered the problems raised above, the work in this Ph.D. thesis carries out extensive researches on the nonlinear compensations utilizing advanced digital signal processing techniques. The motivation behind this is to push more processing tasks to the digital domain, as it can potentially cut down the bill of materials (BOM) costs paid for the off-chip devices and reduce practical implementation difficulties. The work here is carried out using three approaches: numerical analysis & computer simulations; experimental tests using commercial instruments; actual implementation with FPGA. The primary contributions for this thesis are summarized as the following three points: 1) An adaptive digital predistortion (DPD) with fast convergence rate and low complexity for multi-carrier GSM system is presented. Albeit a legacy system, the GSM, however, has a very strict requirement on the out-of-band emission, thus it represents a much more difficult hurdle for DPD application. It is successfully implemented in an FPGA without using any other auxiliary processor. A simplified multiplier-free NLMS algorithm, especially suitable for FPGA implementation, for fast adapting the LUT is proposed. Many design methodologies and practical implementation issues are discussed in details. Experimental results have shown that the DPD performed robustly when it is involved in the multichannel transmitter. 2) The next generation system (5G) will unquestionably use wider bandwidth to support higher throughput, which poses stringent needs for using high-speed data converters. Herein the analog-to-digital converter (ADC) tends to be the most expensive single device in the whole transmitter/receiver systems. Therefore, conventional DPD utilizing high-speed ADC becomes unaffordable, especially for small base stations (micro, pico and femto). A digital predistortion technique utilizing spectral extrapolation is proposed in this thesis, wherein with band-limited feedback signal, the requirement on ADC speed can be significantly released. Experimental results have validated the feasibility of the proposed technique for coping with band-limited feedback signal. It has been shown that adequate linearization performance can be achieved even if the acquisition bandwidth is less than the original signal bandwidth. The experimental results obtained by using LTE-Advanced signal of 320 MHz bandwidth are quite satisfactory, and to the authors’ knowledge, this is the first high-performance wideband DPD ever been reported. 3) To address the predicament that mobile operators do not have enough contiguous usable bandwidth, carrier aggregation (CA) technique is developed and imported into 4G LTE-Advanced. This pushes the utilization of concurrent dual-band transmitter/receiver, which reduces the hardware expense by using a single front-end. Compensation techniques for the respective concurrent dual-band transmitter and receiver front-ends are proposed to combat the inter-band modulation distortion, and simultaneously reduce the distortion for the both lower-side band and upper-side band signals.電気通信大学201

Characterisation of MIMO radio propagation channels

Due to the incessant requirement for higher performance radio systems, wireless designers have been constantly seeking ways to improve spectrum efficiency, link reliability, service quality, and radio network coverage. During the past few years, space-time technology which employs multiple antennas along with suitable signalling schemes and receiver architectures has been seen as a powerful tool for the implementation of the aforementioned requirements. In particular, the concept of communications via Multiple-Input Multiple-Output (MIMO) links has emerged as one of the major contending ideas for next generation ad-hoc and cellular systems. This is inherently due to the capacities expected when multiple antennas are employed at both ends of the radio link. Such a mobile radio propagation channel constitutes a MIMO system. Multiple antenna technologies and in particular MIMO signalling are envisaged for a number of standards such as the next generation of Wireless Local Area Network (WLAN) technology known as 802.1 ln and the development of the Worldwide Interoperability for Microwave Access (WiMAX) project, such as the 802.16e. For the efficient design, performance evaluation and deployment of such multiple antenna (space-time) systems, it becomes increasingly important to understand the characteristics of the spatial radio channel. This criterion has led to the development of new sounding systems, which can measure both spatial and temporal channel information. In this thesis, a novel semi-sequential wideband MIMO sounder is presented, which is suitable for high-resolution radio channel measurements. The sounder produces a frequency modulated continuous wave (FMCW) or chirp signal with variable bandwidth, centre frequency and waveform repetition rate. It has programmable bandwidth up to 300 MHz and waveform repetition rates up to 300 Hz, and could be used to measure conventional high- resolution delay/Doppler information as well as spatial channel information such as Direction of Arrival (DOA) and Direction of Departure (DOD). Notably the knowledge of the angular information at the link ends could be used to properly design and develop systems such as smart antennas. This thesis examines the theory of multiple antenna propagation channels, the sounding architecture required for the measurement of such spatial channel information and the signal processing which is used to quantify and analyse such measurement data. Over 700 measurement files were collected corresponding to over 175,000 impulse responses with different sounder and antenna array configurations. These included measurements in the Universal Mobile Telecommunication Systems Frequency Division Duplex (UMTS-FDD) uplink band, the 2.25 GHz and 5.8 GHz bands allocated for studio broadcast MIMO video links, and the 2.4 GHz and 5.8 GHz ISM bands allocated for Wireless Local Area Network (WLAN) activity as well as for a wide range of future systems defined in the WiMAX project. The measurements were collected predominantly for indoor and some outdoor multiple antenna channels using sounding signals with 60 MHz, 96 MHz and 240 MHz bandwidth. A wide range of different MIMO antenna array configurations are examined in this thesis with varying space, time and frequency resolutions. Measurements can be generally subdivided into three main categories, namely measurements at different locations in the environment (static), measurements while moving at regular intervals step by step (spatial), and measurements while the receiver (or transmitter) is on the move (dynamic). High-scattering as well as time-varying MIMO channels are examined for different antenna array structures

Algorithms and Circuits for Analog-Digital Hybrid Multibeam Arrays

Fifth generation (5G) and beyond wireless communication systems will rely heavily on larger antenna arrays combined with beamforming to mitigate the high free-space path-loss that prevails in millimeter-wave (mmW) and above frequencies. Sharp beams that can support wide bandwidths are desired both at the transmitter and the receiver to leverage the glut of bandwidth available at these frequency bands. Further, multiple simultaneous sharp beams are imperative for such systems to exploit mmW/sub-THz wireless channels using multiple reflected paths simultaneously. Therefore, multibeam antenna arrays that can support wider bandwidths are a key enabler for 5G and beyond systems. In general, N-beam systems using N-element antenna arrays will involve circuit complexities of the order of N2. This dissertation investigates new analog, digital and hybrid low complexity multibeam beamforming algorithms and circuits for reducing the associated high size, weight, and power (SWaP) complexities in larger multibeam arrays. The research efforts on the digital beamforming aspect propose the use of a new class of discrete Fourier transform (DFT) approximations for multibeam generation to eliminate the need for digital multipliers in the beamforming circuitry. For this, 8-, 16- and 32-beam multiplierless multibeam algorithms have been proposed for uniform linear array applications. A 2.4 GHz 16-element array receiver setup and a 5.8 GHz 32-element array receiver system which use field programmable gate arrays (FPGAs) as digital backend have been built for real-time experimental verification of the digital multiplierless algorithms. The multiplierless algorithms have been experimentally verified by digitally measuring beams. It has been shown that the measured beams from the multiplierless algorithms are in good agreement with the exact counterpart algorithms. Analog realizations of the proposed approximate DFT transforms have also been investigated leading to low-complex, high bandwidth circuits in CMOS. Further, a novel approach for reducing the circuit complexity of analog true-time delay (TTD) N-beam beamforming networks using N-element arrays has been proposed for wideband squint-free operation. A sparse factorization of the N-beam delay Vandermonde beamforming matrix is used to reduce the total amount of TTD elements that are needed for obtaining N number of beams in a wideband array. The method has been verified using measured responses of CMOS all-pass filters (APFs). The wideband squint-free multibeam algorithm is also used to propose a new low-complexity hybrid beamforming architecture targeting future 5G mmW systems. Apart from that, the dissertation also explores multibeam beamforming architectures for uniform circular arrays (UCAs). An algorithm having N log N circuit complexity for simultaneous generation of N-beams in an N-element UCA is explored and verified