Hydrodynamics of Biomimetic Marine Propulsion and Trends in Computational Simulations

[Abstract] The aim of the present paper is to provide the state of the works in the field of hydrodynamics and computational simulations to analyze biomimetic marine propulsors. Over the last years, many researchers postulated that some fish movements are more efficient and maneuverable than traditional rotary propellers, and the most relevant marine propulsors which mimic fishes are shown in the present work. Taking into account the complexity and cost of some experimental setups, numerical models offer an efficient, cheap, and fast alternative tool to analyze biomimetic marine propulsors. Besides, numerical models provide information that cannot be obtained using experimental techniques. Since the literature about trends in computational simulations is still scarce, this paper also recalls the hydrodynamics of the swimming modes occurring in fish and summarizes the more relevant lines of investigation of computational models

Observation and analysis of diving beetle movements while swimming

The fast swimming speed, flexible cornering, and high propulsion efficiency of diving beetles are primarily achieved by their two powerful hind legs. Unlike other aquatic organisms, such as turtle, jellyfish, fish and frog et al., the diving beetle could complete retreating motion without turning around, and the turning radius is small for this kind of propulsion mode. However, most bionic vehicles have not contained these advantages, the study about this propulsion method is useful for the design of bionic robots. In this paper, the swimming videos of the diving beetle, including forwarding, turning and retreating, were captured by two synchronized high-speed cameras, and were analyzed via SIMI Motion. The analysis results revealed that the swimming speed initially increased quickly to a maximum at 60% of the power stroke, and then decreased. During the power stroke, the diving beetle stretched its tibias and tarsi, the bristles on both sides of which were shaped like paddles, to maximize the cross-sectional areas against the water to achieve the maximum thrust. During the recovery stroke, the diving beetle rotated its tarsi and folded the bristles to minimize the cross-sectional areas to reduce the drag force. For one turning motion (turn right about 90 degrees), it takes only one motion cycle for the diving beetle to complete it. During the retreating motion, the average acceleration was close to 9.8 m/s2 in the first 25 ms. Finally, based on the diving beetle's hind-leg movement pattern, a kinematic model was constructed, and according to this model and the motion data of the joint angles, the motion trajectories of the hind legs were obtained by using MATLAB. Since the advantages of this propulsion method, it may become a new bionic propulsion method, and the motion data and kinematic model of the hind legs will be helpful in the design of bionic underwater unmanned vehicles

Review of Computational Fluid Dynamics Analysis in Biomimetic Applications for Underwater Vehicles

Biomimetics, which draws inspiration from nature, has emerged as a key approach in the development of underwater vehicles. The integration of this approach with computational fluid dynamics (CFD) has further propelled research in this field. CFD, as an effective tool for dynamic analysis, contributes significantly to understanding and resolving complex fluid dynamic problems in underwater vehicles. Biomimetics seeks to harness innovative inspiration from the biological world. Through the imitation of the structure, behavior, and functions of organisms, biomimetics enables the creation of efficient and unique designs. These designs are aimed at enhancing the speed, reliability, and maneuverability of underwater vehicles, as well as reducing drag and noise. CFD technology, which is capable of precisely predicting and simulating fluid flow behaviors, plays a crucial role in optimizing the structural design of underwater vehicles, thereby significantly enhancing their hydrodynamic and kinematic performances. Combining biomimetics and CFD technology introduces a novel approach to underwater vehicle design and unveils broad prospects for research in natural science and engineering applications. Consequently, this paper aims to review the application of CFD technology in the biomimicry of underwater vehicles, with a primary focus on biomimetic propulsion, biomimetic drag reduction, and biomimetic noise reduction. Additionally, it explores the challenges faced in this field and anticipates future advancements

A numerical study of fin and jet propulsions involving fluid-structure interactions

Fish swimming is elegant and efficient, which inspires humans to learn from them to design high-performance artificial underwater vehicles. Research on aquatic locomotion has made extensive progress towards a better understanding of how aquatic animals control their flexible body and fin for propulsion. Although the structural flexibility and deformation of the body and fin are believed to be important features to achieve optimal swimming performance, studies on high-fidelity deformable body and fin with complex material behavior, such as non-uniform stiffness distributions, are rare. In this thesis, a fully coupled three-dimensional high-fidelity fluid-structure interaction (FSI) solver is developed to investigate the flow field evolution and propulsion performance of caudal fin and jet propulsion involving body and/or fin deformation. Within this FSI solver, the fluid is resolved by solving unsteady and viscous Navier-Stokes equations based on the finite volume method with a multi-block grid system. The solid dynamics are solved by a nonlinear finite element method. The coupling between the two solvers is achieved in a partitioned approach in which convergence check and sub-iteration are implemented to ensure numerical stability and accuracy. Validations are conducted by comparing the simulation results of classical benchmarks with previous data in the literature, and good agreements between them are obtained. The developed FSI solver is then applied to study the bio-inspired fin and jet propulsion involving body deformation. Specifically, the effect of non-uniform stiffness distributions of fish body and/or fin, key features of fish swimming which have been excluded in most previous studies, on the propulsive performance is first investigated. Simulation results of a sunfish-like caudal fin model and a tuna-inspired swimmer model both show that larger thrust and propulsion efficiency can be achieved by a non-uniform stiffness distribution (e.g., increased by 11.2% and 9.9%, respectively, for the sunfish-like model) compared with a uniform stiffness profile. Despite the improved propulsive e performance, a bionic variable fish body stiffness does not yield fish-like midline kinematics observed in real fish, suggesting that fish movement involves significant active control that cannot be replicated purely by passive deformations. Subsequent studies focus on the jet propulsion inspired by squid locomotion using the developed numerical solver. Simulation results of a two-dimensional inflation-deflation jet propulsion system, whose inflation is actuated by an added external force that mimics the muscle constriction of the mantle and deflation is caused by the release of elastic energy of the structure, suggest larger mean thrust production and higher efficiency in high Reynolds number scenarios compared with the cases in laminar flow. A unique symmetry-breaking instability in turbulent flow is found to stem from irregular internal body vortices, which cause symmetry breaking in the wake. Besides, a three-dimensional squid-like jet propulsion system in the presence of background flow is studied by prescribing the body deformation and jet velocity profiles. The effect of the background flow on the leading vortex ring formation and jet propulsion is investigated, and the thrust sources of the overall pulsed jet are revealed as well. Finally, FSI analysis on motion control of a self-propelled flexible swimmer in front of a cylinder utilizing proportional-derivative (PD) control is conducted. The amplitude of the actuation force, which is applied to the swimmer to bend it to produce thrust, is dynamically tuned by a feedback PD controller to instruct the swimmer to swim the desired distance from an initial position to a target location and then hold the station there. Despite the same swimming distance, a swimmer whose departure location is closer to the cylinder requires less energy consumption to reach the target and hold the position there.Fish swimming is elegant and efficient, which inspires humans to learn from them to design high-performance artificial underwater vehicles. Research on aquatic locomotion has made extensive progress towards a better understanding of how aquatic animals control their flexible body and fin for propulsion. Although the structural flexibility and deformation of the body and fin are believed to be important features to achieve optimal swimming performance, studies on high-fidelity deformable body and fin with complex material behavior, such as non-uniform stiffness distributions, are rare. In this thesis, a fully coupled three-dimensional high-fidelity fluid-structure interaction (FSI) solver is developed to investigate the flow field evolution and propulsion performance of caudal fin and jet propulsion involving body and/or fin deformation. Within this FSI solver, the fluid is resolved by solving unsteady and viscous Navier-Stokes equations based on the finite volume method with a multi-block grid system. The solid dynamics are solved by a nonlinear finite element method. The coupling between the two solvers is achieved in a partitioned approach in which convergence check and sub-iteration are implemented to ensure numerical stability and accuracy. Validations are conducted by comparing the simulation results of classical benchmarks with previous data in the literature, and good agreements between them are obtained. The developed FSI solver is then applied to study the bio-inspired fin and jet propulsion involving body deformation. Specifically, the effect of non-uniform stiffness distributions of fish body and/or fin, key features of fish swimming which have been excluded in most previous studies, on the propulsive performance is first investigated. Simulation results of a sunfish-like caudal fin model and a tuna-inspired swimmer model both show that larger thrust and propulsion efficiency can be achieved by a non-uniform stiffness distribution (e.g., increased by 11.2% and 9.9%, respectively, for the sunfish-like model) compared with a uniform stiffness profile. Despite the improved propulsive e performance, a bionic variable fish body stiffness does not yield fish-like midline kinematics observed in real fish, suggesting that fish movement involves significant active control that cannot be replicated purely by passive deformations. Subsequent studies focus on the jet propulsion inspired by squid locomotion using the developed numerical solver. Simulation results of a two-dimensional inflation-deflation jet propulsion system, whose inflation is actuated by an added external force that mimics the muscle constriction of the mantle and deflation is caused by the release of elastic energy of the structure, suggest larger mean thrust production and higher efficiency in high Reynolds number scenarios compared with the cases in laminar flow. A unique symmetry-breaking instability in turbulent flow is found to stem from irregular internal body vortices, which cause symmetry breaking in the wake. Besides, a three-dimensional squid-like jet propulsion system in the presence of background flow is studied by prescribing the body deformation and jet velocity profiles. The effect of the background flow on the leading vortex ring formation and jet propulsion is investigated, and the thrust sources of the overall pulsed jet are revealed as well. Finally, FSI analysis on motion control of a self-propelled flexible swimmer in front of a cylinder utilizing proportional-derivative (PD) control is conducted. The amplitude of the actuation force, which is applied to the swimmer to bend it to produce thrust, is dynamically tuned by a feedback PD controller to instruct the swimmer to swim the desired distance from an initial position to a target location and then hold the station there. Despite the same swimming distance, a swimmer whose departure location is closer to the cylinder requires less energy consumption to reach the target and hold the position there

Intersection between natural and artificial swimmers: a scaling approach to underwater vehicle design.

Approximately 72% of the Earth’s surface is covered by water, yet only 20% has been mapped [1]. Autonomous Underwater Vehicles (AUVs) are one of the main tools for ocean exploration. The demand for AUVs is expected to increase rapidly in the coming years [2], so there is a need for faster and more energy efficient AUVs. A drawback to using this type of vehicle is the finite amount of energy that is stored onboard in the form of batteries. Science and roboticists have been studying nature for ways to move more efficiently. Phillips et al. [3] presents data that contradicts the idea that fish are better swimmers than conventional AUVs when comparing the energetic cost of swimming in the form of the Cost of Transport (COT). The data presented by Phillips et al. only applies to AUVs at higher length and naval displacement (mass) scales, so the question arises of whether an AUV built at different displacements and length scales is more efficient than biological animals and if current bio-inspired platforms are better than conventional AUVs. Besides power requirements, it is also useful to compare the kinematic parameters of natural and artificial swimmers. In this case, kinematic parameters indicate how fast the swimmer travels through the water. Also, they describe how fast the propulsion mechanism must act to reach a certain swimming speed. This research adopts the approach of Gazzola et al. [4] where the Reynolds number is associated with a dimensionless number, Swim number (Sw) in this case, that has all the kinematic information. A newly developed number that extends the swim number to conventional AUVs is the Propulsion number (Jw), which demonstrates excellent agreement with the kinematics of conventional AUVs. Despite being functionally similar, Sw and Jw do not have a one-to-one relationship. Sw, Jw, COT represent key performance metrics for an AUV, herein called performance criteria, which can be used to compare existing platforms with each other and estimate the performance of non-existent designs. The scaling laws are derived by evaluating the performance of 229 biological animals, 163 bioinspire platforms, and 109 conventional AUVs. AUVs and bio-inspired platforms have scarce data compared with biological swimmers. Only 5% of conventional and 38% of bio-inspired AUVs have kinematic data while 30% of conventional and 18% of bio-inspired AUVs have energetic data. The low amount of performance criteria data is due to the nature of most conventional AUVs as commercial products. Only recently has the COT metric been included in the performance criteria for bio-inspired AUVs. For this reason, the research here formulates everything in terms of allometric scaling laws. This type of formulation is used extensively when referring to biological systems and is defined by an exponential relationship f (x) = axb, where x is a physical parameter of the fish or vehicle, like length or displacement. Scaling laws have the added benefit of allowing comparisons with limited data, as is the case for AUVs. The length and displacement scale (physical scale) must be established before estimating the performance criteria. Scale is primarily determined by the payload needed for a particular application. For instance, surveying the water column in deep water will require different scientific tools than taking images of an oyster bed in an estuary. There is no way to identify the size of an AUV until it is designed for that application, since these scientific instruments each have their own volume, length, and weight. A methodology for estimating physical parameters using computer vision is presented to help determine the scale for the vehicle. It allows accurate scaling of physical parameters of biological and bio-inspired swimmers with only a side and top view of the platform. A physical scale can also be determined based on the vehicle’s overall volume, which is useful when determining how much payload is needed for a particular application. Further, this can be used in conjunction with 3D modeling software to scale nonexistent platforms. Following the establishment of a physical scale, which locomotion mode would be most appropriate? Unlike conventional AUVs that use propeller or glider locomotion, bio-inspired platforms use a variety of modes. Kinematics and energy expenditures are different for each of these modes. For bio-inspired vehicles, the focus will be on the body-caudal fin (BCF) locomotion, of which four types exist: anguilliform, carangiform, thunniform, and ostraciiform. There is ample research on anguilliform and carangiform locomotion modes, but little research on thunniform and ostraciiform modes. In order to determine which locomotion mode scales best for a bio-inspired AUV, this research examines the power output and kinematic parameters for all four BCF modes. In order to achieve this, computational fluid dynamics simulations are performed on a 2D swimmer for all four modes. Overset meshes are used in lieu of body-fitted meshes to increase stability and decrease computational time. These simulations were used to scale output power over several decades of Reynolds numbers for each locomotion mode. Carangiform locomotion was found to be the most energy efficient, followed by anguilliform, thunniform, and ostraciiform. In order to utilize the above scaling laws in designing a novel platform, or comparing an existing one, there must be a unifying framework. The framework for choosing a suitable platform is presented with a case study of two bio-inspired vehicles and a conventional one. The framework begins by determining how the platform can be physically scaled depending on the payload. Based on the physical scale and derived scaling laws, it then determines performance criteria. It also describes a method for relative cost scaling for each vehicle, which is not covered in the literature. The cost scaling is based on the assumption that all payloads and materials are the same. The case study shows that a conventional AUV performs better on all performance criteria and would cost less to build

3D locomotion biomimetic robot fish with haptic feedback

This thesis developed a biomimetic robot fish and built a novel haptic robot fish system based on the kinematic modelling and three-dimentional computational fluid dynamic (CFD) hydrodynamic analysis. The most important contribution is the successful CFD simulation of the robot fish, supporting users in understanding the hydrodynamic properties around it

Bio-Inspired Robotics

Modern robotic technologies have enabled robots to operate in a variety of unstructured and dynamically-changing environments, in addition to traditional structured environments. Robots have, thus, become an important element in our everyday lives. One key approach to develop such intelligent and autonomous robots is to draw inspiration from biological systems. Biological structure, mechanisms, and underlying principles have the potential to provide new ideas to support the improvement of conventional robotic designs and control. Such biological principles usually originate from animal or even plant models, for robots, which can sense, think, walk, swim, crawl, jump or even fly. Thus, it is believed that these bio-inspired methods are becoming increasingly important in the face of complex applications. Bio-inspired robotics is leading to the study of innovative structures and computing with sensory–motor coordination and learning to achieve intelligence, flexibility, stability, and adaptation for emergent robotic applications, such as manipulation, learning, and control. This Special Issue invites original papers of innovative ideas and concepts, new discoveries and improvements, and novel applications and business models relevant to the selected topics of ``Bio-Inspired Robotics''. Bio-Inspired Robotics is a broad topic and an ongoing expanding field. This Special Issue collates 30 papers that address some of the important challenges and opportunities in this broad and expanding field

生物模倣ソフト魚ロボットの研究開発

In nature, the environment varies from day to day. Through natural selection and competition law of survival of the fittest, the winning creatures survive and their species are able to retain and persist in nature. Based on this fact, creatures existent in nature have their unique features and advantages adapt to the surrounding environment. In recent years, many researches focused on the features of the creatures in nature have been done actively to clarify their morphology and functions and apply the morphology and functions to various fields. Among these researches, the development of the biomimetic robots based on mimicking the creature’s structures and functions has become an active field in robotics recently. In the research, the development of biomimetic robotic fish is focused. So far, there are many researches on biomimetic robotic fish, but improvement on motion performances and efficiency is still an important issue for robot development. Specially, on the biomimetic soft robotic fish utilizing the flexibility of fishes, the developments have been done by the trial and error approach. That is, the design and control method of soft robotic fish has not been established currently. Therefore, it motives us to investigate the design and control of soft robotic fish by numerical simulation that takes into account the interaction between flexible structure and surrounding fluid to develop the biomimetic soft robotic fish with high performance. In order to develop the biomimetic soft robotic fish with high performance, the basic design method and corresponding numerical simulation system are firstly proposed and constructed in this dissertation. Then, based on finite element method (FEM), modelling of soft robotic fish by mimicking the soft structure and driving mechanism of fishes is carried out. The propulsion motion and propulsive force of the soft robotic fish are investigated through two kinds of numerical analyses. One is the modal and transient analysis considering the surrounding fluid as acoustic fluid. The propulsion mode and amplitude of the propulsion motion of soft robotic fish corresponding directly to the propulsion mechanism and motion performance of the robotic fish can be investigated. The other is the fluid-structure interaction (FSI) analysis. The interaction between soft robot structure and surrounding fluid including the dissipation due to fluid viscosity and influence of wake performance around the soft robotic fish are taken into account. From FSI analysis, the hydrodynamic performances of the soft robotic fish can be obtained for investigating its propulsion motion. It is possible to further improve the performance of the soft robotic fish through its design and control based on FSI analysis. Besides, based on coupling analysis by using acoustic fluid, the turning motion control of the soft robotic fish is investigated by its propulsion modes in the fluid. In order to investigate the feasibility of modelling method and numerical simulation analysis on design and control of the biomimetic soft robotic fish, the performance evaluation is carried out by comparison between the simulation and experiment on an actual prototype. Finally, the optimization and improvement are performed for developing the biomimetic soft robotic fish with higher performance based on verified coupling analysis considering the fluid as acoustic fluid, and corresponding performance evaluation on new robot prototype is presented. The performance improvement of the soft robotic fish is confirmed through the new robot prototype. The dissertation consists of six chapters and the main contents are shown as follows. Chapter 1 is an introduction. The background and relative previous work about biomimetic soft robotic fish are briefly reviewed. It summarizes the current research status and problems of biomimetic soft robotic fish, and describes the purposes of this research. Chapter 2 presents the design method, procedures and numerical simulation system in the present research for developing the biomimetic soft robotic fish with high performance. Different from previous development method, our purpose is how to design and control the soft robotic fish by utilizing interaction between the flexible structure and surrounding fluid effectively based on numerical simulations. Therefore, it is necessary to model a fish-like soft robot structure including soft actuators and an enclosed fluid. Besides, by the numerical analysis considering the interaction between flexible structure and fluid, the fish-like propulsion motion should be realized and established, and then the robot structure and control inputs are needed to be optimized for performance improvement. In order to meet these requirements of designing and developing the optimal soft robotic fish, the design method based on modelling, simulation analysis and improvement is presented and the numerical simulation system for soft robotic fish is built. In the simulation system, modelling of soft robotic fish, modal and transient analysis considering the enclosed fluid as acoustic fluid are firstly described based on FEM to realize the fish-like propulsion motion with large amplitude for the soft robotic fish. Then, the FSI analysis is performed to describe and establish the hydrodynamic performances of the soft robotic fish. Based on this numerical simulation system, it is possible to develop the biomimetic soft robotic fish with high performance effectively by optimization of design and control of the soft robotic fish. Chapter 3 describes the modelling and numerical analysis of biomimetic soft robotic fish by using the method presented in Chapter 2. The soft robotic fish uses the piezoelectric fiber composite (PFC) as soft actuator. Firstly, the relationships between the input voltage and generated stress of the PFC are derived. The generated stress can be applied on soft structure to investigate the motion performance of the soft robotic fish. To support the driving model of the PFC, the corresponding experiments on simple beam model are carried out. By comparing the simulation results with experimental results, the effectiveness of the driving model is verified. Then, the modal analysis in which the fluid is considered as acoustic fluid is performed. The structural mode frequencies and mode shapes of the soft robotic fish in the fluid are calculated. By comparing these modes’ motion with those of the real fishes, the fish-like propulsion mode is identified to realize the corresponding propulsion motion of the soft robotic fish. Furthermore, based on the verified driving model of soft actuator, the amplitude of the main propulsion motion of soft robotic fish is calculated. Through FSI analysis, the relationships of driving frequencies of input signal with propulsive force and displacement of propulsion motion, and vortex distribution in the wake around the soft robotic fish are investigated for the case of fixing robot head. Besides, the motion control of soft robot is investigated to realize turning motion in the fluid. Through controlling the input voltage amplitude on soft actuators of the robot, turning right and turning left motion are identified in the swimming when the input voltage amplitudes on two actuators are in asymmetric distribution. Chapter 4 is experiment evaluation. In order to validate the results of numerical simulation analysis described in Chapter 3, the mode shapes, amplitude of propulsion motion, propulsive force and vortex distribution around soft robotic fish for the case of fixing robot head, and turning motion are measured by using actual robot prototype. The present simulation results are congruent with experiments. By the results, the effectiveness of the modelling method and numerical analysis used in the research is verified and they are useful to predict the propulsion characteristics of the soft robotic fish in the fluid for performance improvement. Chapter 5 develops a new soft robotic fish with high performance based on above modelling method and numerical analysis by optimization. Firstly, the structural parameters of the robot are allowed to vary within a range and the amplitude of the propulsion motion for the soft robot is calculated for different parameters by the numerical analysis. Then the structural parameters of the robot capable of propulsion motion with largeramplitude are chosen for improvement. Based on this result, new soft robot is designed and evaluated by experiments. From the experimental results of the new soft robot, it is confirmed that the higher swimming speed, better fish-like swimming performance and larger turning velocity are realized. It can be said that the new soft robotic fish has been developed successfully for improvement. Chapter 6 summarizes the conclusions and future works of this research.電気通信大学201

Energy Based Control System Designs for Underactuated Robot Fish Propulsion

In nature through millions of years of evolution fish and cetaceans have developed fast efficient and highly manoeuvrable methods of marine propulsion. A recent explosion in demand for sub sea robotics, for conducting tasks such as sub sea exploration and survey has left developers desiring to capture some of the novel mechanisms evolved by fish and cetaceans to increase the efficiency of speed and manoeuvrability of sub sea robots. Research has revealed that interactions with vortices and other unsteady fluid effects play a significant role in the efficiency of fish and cetaceans. However attempts to duplicate this with robotic fish have been limited by the difficulty of predicting or sensing such uncertain fluid effects. This study aims to develop a gait generation method for a robotic fish with a degree of passivity which could allow the body to dynamically interact with and potentially synchronise with vortices within the flow without the need to actually sense them. In this study this is achieved through the development of a novel energy based gait generation tactic, where the gait of the robotic fish is determined through regulation of the state energy rather than absolute state position. Rather than treating fluid interactions as undesirable disturbances and `fighting' them to maintain a rigid geometric defined gait, energy based control allows the disturbances to the system generated by vortices in the surrounding flow to contribute to the energy of the system and hence the dynamic motion. Three different energy controllers are presented within this thesis, a deadbeat energy controller equivalent to an analytically optimised model predictive controller, a $H_\infty$ disturbance rejecting controller with a novel gradient decent optimisation and finally a error feedback controller with a novel alternative error metric. The controllers were tested on a robotic fish simulation platform developed within this project. The simulation platform consisted of the solution of a series of ordinary differential equations for solid body dynamics coupled with a finite element incompressible fluid dynamic simulation of the surrounding flow. results demonstrated the effectiveness of the energy based control approach and illustrate the importance of choice of controller in performance

Hydrodynamics of pitching foils: flexibility and ground effects

En termes de propulsió la rigidesa flexural i l'efecte terra en una placa rectangular en piteig pur han estat investigats. Velocimetria per imatges per partícules, mesures de forces i moments amb una cèl·lula de carga de 6 eixos, mesures de velocitat i adquisició d'imatges de la cinemàtica de la placa han estat realitzades per estudiar els patrons de flux i les forces hidrodinàmiques en plaques de diferent flexibilitat. La presència de la paret va millorar la velocitat de creuer fins a un 25% i l'empenta fins a un 45% per angles escombrats de 160 i 240 graus. El mecanisme físic sota aquest efecte és discutit estudiant els camps de vorticitat produïts per l'estela de l'aleta bioinspirada en un rajiforme. Les forces hidrodinàmiques linkejades a les tècniques de visualització, van permetre calcular eficiències i camps de vorticitat promitjats en fase. Aquestes dades van revelar com l'angle escombrat de la placa juga un paper fonamental en la distribució de moment en l'estela d'una placa rígida per incrementar la propulsió. En termes de rigidesa flexural, l'òptima flexibilitat va ser determinada amb una placa semi-flexible amb una eficiència d'un 69% amb un angle d'atac de 72 graus.En términos de propulsión la rigidez flexural y el efecto suelo en una placa rectangular en puro picheo han sido investigados. Velocimetría de imágenes por partículas, medidas de fuerzas y momentos con una célula de carga de 6 ejes, medidas de velocidad y adquisiciones de imágenes de la cinemática de la placa han sido realizadas para estudiar los patrones de flujo y las fuerzas hidrodinámicas en placas con diferentes flexibilidad. La presencia de la pared mejoró la velocidad de crucero hasta en un 25% y el empuje hasta un 45% para ángulos barridos de 160 y 240 grados. El mecanismo físico bajo este efecto es discutido estudiando los campos de vorticidad producidos por la estela de la aleta bioinspirada en un rajiforme. Las fuerzas hidrodinámicas linkadas a las técnicas de visualización, permitieron calcular eficiencias y campos de vorticidad promediados en fase. Estos datos revelaron como el ángulo barrido de la placa juega un papel fundamental en la distribución de momento en la estela de un foil rígido para incrementar la propulsión. En términos de rigidez flexural la óptima flexibilidad fue determinada con la placa semi-flexible con una eficiencia de un 69% con un ángulo de ataque de 72 grados.The roles of the chordwise flexural stiffness and ground effect in a rectangular plate undergoing in pure pitching motion have been investigated. Digital Particle image velocimetry (DPIV), load measurement with a 6-axes balance, measurements of the swimming speed and image acquisition of the kinematics of the foil have been done to study the flow patterns and hydrodynamics forces around the flapping flexible plates. The presence of the wall enhances the cruising velocity in some cases up to 25% and the thrust by a 45% , for swept angles of 160 and 240°. The physical mechanisms underlying of this effect are discussed by studying the vorticity dynamics in the wake of the foil. Experimental data of the hydrodynamic forces and moments allowed to obtain the efficiencies of the flapping propulsion. These load measurements were linked to the wakes of the flapping foils in order to reveal configurations with higher thrust. The momentum distribution in the wake of the foil has allowed the physical explanation for the cases with highest thrust production capacity. In terms of flexural stiffness, the optimum flexibility has been determined with the semi − flexible plate up to 69% of efficiency under a swept angle of 72 degrees for Re = O(10^4) tested in the investigation