5nm 이하 3D Transistors의 Self-Heating 및 전열특성분석 연구

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·컴퓨터공학부, 2021.8. 신형철.In this thesis, Self-Heating Effect (SHE) is investigated using TCAD simulations in various Sub-10-nm node Field Effect Transistor (FET). As the node decreases, logic devices have evolved into 3D MOSFET structures from Fin-FET to Nanosheet-FET. In the case of 3D MOSFET, there are thermal reliability issues due to the following reasons: ⅰ) The power density of the channel is high, ⅱ) The channel structure surrounded by SiO2, ⅲ) The overall low thermal conductivity characteristics due to scaling down. Many papers introduce the analysis and prediction of temperature rise by SHE in the device, but there are no papers presenting the content of mitigation of temperature rise. Therefore, we have studied the methods of decreasing the maximum lattice temperature (TL,max) such as shallow trench isolation (STI) composition engineering in Fin-FET, thermal analysis according to DC/AC/duty cycle in nanowire-FET, and active region ( e.g., gate metal thickness, channel width, channel number etc..) optimization in nanosheet-FET. In addition, lifetime affected by hot carrier injection (HCI) / bias-temperature instability (BTI) is also analyzed according to various thermal relaxation methods presented.이 논문에서는 다양한 Sub-10nm 노드 전계 효과 트랜지스터 (FET)에서 TCAD 시뮬레이션을 사용하여 자체 발열 효과 (SHE)를 조사합니다. 노드가 감소함에 따라 논리 장치는 Fin-FET에서 Nanosheet-FET로 3D MOSFET 구조로 진화했습니다. 3D MOSFET의 경우 ⅰ) 채널의 전력 밀도가 높음, ⅱ) SiO2로 둘러싸인 채널 구조, ⅲ) 축소로 인해 전체적으로 낮은 열전도 특성 등 다음과 같은 이유로 열 신뢰성 문제가 있습니다. 한편, 많은 논문이 device에서 SHE에 의한 온도 상승의 분석 및 예측을 소개하지만 온도 상승 완화의 내용을 제시하는 논문은 거의 없습니다. 따라서 Fin-FET의 STI (Shallow Trench Isolation) 구성 공학, nanowire-FET의 DC / AC / 듀티 사이클에 따른 열 분석, nanosheet-FET에서 소자의 중요영역(예: 게이트 금속 두께, 채널 폭, 채널 번호 등)의 최적화를 통해서 최대 격자 온도 (TL,max)를 낮추는 방법등을 연구했습니다. 또한 더 나아가서 HCI (Hot Carrier Injection) / BTI (Bias-Temperature Instability)의 영향을 받는 수명도 제시된 다양한 열 완화 방법에 따라 분석하여 소자의 제작에 있어 열적 특성과 수명을 좋게 만드는 지표를 제시합니다 .Chapter 1 Introduction 1 1.1. Development of Semconductor structure 1 1.2. Self-Heating Effect issues in semiconductor devices 3 Chapter 2 Thermal-Aware Shallow Trench Isolation Design Optimization for Minimizing Ioff in Various Sub-10-nm 3-D Transistor 7 2.1. Introduction 7 2.2. Device Structure and Simulation Condition 7 2.3. Results and Discussion 12 2.4. Summary 27 Chapter 3 Analysis of Self Heating Effect in DC/AC Mode in Multi-channel GAA-Field Effect Transistor 32 3.1. Introduction 32 3.2. Multi-Channel Nanowire FET and Back End Of Line 33 3.3. Work Flow and Calibration Process 35 3.4. More Detailed Thermal Simulation of Nanowire-FET 37 3.5. Performance Analysis by Number of Channels 38 3.6. DC Characteristic of SHE in Nanowire-FETs 40 3.7. AC Characteristics of SHE in Nanowire-FETs 43 3.8. Summary 51 Chapter 4 Self-Heating and Electrothermal Properties of Advanced Sub-5-nm node Nanoplate FET 56 4.1. Introduction 56 4.2. Device Structure and Simulation Condition 57 4.3. Thermal characteristics by channel number and width 62 4.4. Thermal characteristics by inter layer-metal thickness (TM) 64 4.5. Life Time Prediction 65 4.6. Summary 67 Chapter 5 Study on Self Heating Effect and life time in Vertical-channel Field Effect Transistor 72 5.1. Introduction 72 5.2. Device Structure and Simulation Condition 72 5.3. Temperature and RTH according to channel width(TW) 76 5.4. Thermal properties according to air spacers and air gap 77 5.5. Ion boosting according to Channel numbers 81 5.6. Temperature imbalance of multi-channel VFETs 82 5.7. Mitigation of the channel temperature imbalance 86 5.8. Life time depending on various analysis conditions 88 5.9. Summary 89 Chapter 6 Conclusions 93 Appendix A. A Simple and Accurate Modeling Method of Channel Thermal Noise Using BSIM4 Noise Models 95 A.1. Introduction 95 A.2. Overall Schematic of the RF MOSFET Model 97 A.3. Verification of the DC Characteristics of the RF MOSFET Model 98 A.4. Verification of the MOSFET Model with Measured Y-parameters 100 A.5. Verification of the MOSFET Model with Measured Noise Parameters 101 A.6. Thermal Noise Extraction and Modeling (TNOIMOD = 0) 103 A.7. Verification of the Enhanced Model with Noise Parameters 112 A.8. Holistic Model (TNOIMOD = 1) 114 A.9. Evaluation the validity of the model for drain bias 115 A.10. Conclusion 117 Abstract in Korean 122박

Caractérisation électrique des propriétés d'interface dans les MOSFET nanométriques par des mesures de bruit basse fréquence

In this thesis, electrical properties of gate oxide/channel interface in ultra-scaled nanowire (NW) MOSFETs were experimentally investigated by carrier transport and low-frequency noise (LFN) characterizations. NW FETs, which have aggressively downscaled cross-section of the body, are strong candidates for near future CMOS node. However, the interface quality could be a critical issue due to the large surface/volume ratio, the multiple surface orientations, and additional strain technology to enhance the performance. Understanding of carrier transport and channel interface quality in NW FETs with advanced high-k/metal gate is thus particularly important. LFN provides deep insights into the interface properties of MOSFET without lower limit of required channel size. LFN measurement thus can be a powerful technique for ultra-scaled NW FETs. Also, fitting mobility (such as low-field mobility) extraction by Y-function method is an efficient method. Omega-gate NW FETs were fabricated from FD-SOI substrates, and with Hf-based high-k/metal gate (HfSiON/TiN), reducing detrimental effects by device downscaling. In addition, strain technologies to the channel were additively processed. Tensile strained-SOI substrate was used for NMOS, whereas compressive stressors were used for PMOS devices. Strained Si channel for PMOS was processed by raised SiGe S/D and CESL formations. Strained SiGe channel (SGOI) was also fabricated for further high-performance PMOS FETs. Firstly, the most common Id-Vg was characterized in single-channel NW FETs as the basic performance. Reference SOI NWs provided the excellent static control down to short channel of 17nm. Stressors dramatically enhanced on-current owing to a modification of channel energy-band structure. Then, extracted low-field mobility in NWs also showed large improvement of the performance by stressors. The mobility extraction effectively evaluated FET performance even for ultra-scaled NWs. Next, LFN investigated for various technological and architectural parameters. Carrier number fluctuations with correlated mobility fluctuations (CNF+CMF) model described 1/f noise in all our FETs down to the shortest NWs. Drain current noise behavior was basically similar in both N- and PMOS FETs regardless of technological splits. Larger 1/f noise stemming from S/D regions in PMOS FETs was perfectly interpreted by the CNF+CMF model completed with Rsd fluctuations. This observation highlighted an advantage of SGOI NW with the lowest level of S/D region noise. Geometrical variations altered the CNF component with simple impact of device scaling (reciprocal to both Wtot and Lg). No large impact of surface orientation difference between the channel (100) top and (110) side-walls in [110]-oriented NWs was observed. Scaling regularity with both Wtot and Lg, without much quantum effect, could be attributed to the use of HfSiON/TiN gate and carrier transport occurring mostly near top and side-wall surfaces even in NW geometry. Meanwhile, the CMF factor was not altered by decreasing dimensions, while the mobility strongly depends on the impact. Extracted oxide trap density was roughly steady with scaling, structure, and technological parameter impacts. Simple separation method of the contributions between channel top surface and side-walls was demonstrated in order to evaluate the difference. It revealed that oxide quality on (100) top and (110) side-walls was roughly comparable in all the [110]-devices. The density values lie in similar order as the recent reports. An excellent quality of the interface with HfSiON/TiN gate was thus sustained for all our technological and geometrical splits. Finally, our NWs fulfilled 1/f LFN requirements stated in the ITRS 2013 for future MG CMOS logic node. Consequently, we concluded that appropriate strain technologies powerfully improve both carrier transport and LFN property for future CMOS circuits consisting of NW FETs, without any large concern about the interface quality.Dans cette thèse, les propriétés électriques de transistors à nanofils de silicium liées à l'interface oxyde de grille/canal ont été étudiées par le biais de mesures de bruit basse fréquence (bruit 1/f) et de transport dans le canal. Ces transistors nanofils dont les dimensions ont été réduites jusqu'à quelques nanomètres pour la section, représentent une alternative sérieuse pour les futurs nœuds technologiques CMOS. Cependant, la qualité de l'interface oxyde de grille/canal pose question pour transistors dont l'architecture s'étend dans les 3 dimensions, en raison du fort rapport surface/volume inhérent à ces transistors, des différentes orientations cristallographiques de ces interfaces, ou encore des matériaux contraints utilisés pour améliorer les performances électriques. La compréhension des liens entre les propriétés de transport des porteurs dans le canal, qui garantissent en grande partie les performances électriques des transistors, et la qualité de l'interface avec l'oxyde de grille est fond primordiale pour optimiser les transistors nanofils. Les mesures de bruit, associées à l'étude du transport dans le canal, sont un outil puissant et adapté à ces dispositifs tridimensionnels, sans être limité par la taille ultra-réduite des transistors nanofils. Les transistors nanofils étudiés ont été fabriqués à partir de substrats minces SOI, et intègrent un empilement de grille HfSiON/TiN, qui permet de réduire les dimensions tout en conservant les mêmes propriétés électrostatiques. Pour gagner en performances, des contraintes mécaniques ont été introduites dans le canal en silicium : en tension pour les NMOS, par le biais de substrat contraint (sSOI), et en compression pour les PMOS. Un canal en compression uni-axiale peut être obtenu par l'intégration de source/drain en SiGe et/ou par l'utilisation de couches contraintes de type CESL. Des transistors à canal SiGe sur isolant en compression ont également été fabriqués et étudiés. Les caractéristiques électriques des divers transistors nanofils (courbes Id-Vg, compromis Ion-Ioff, mobilité des porteurs) démontrent l'excellent contrôle électrostatique dû à l'architecture 3D, ainsi que l'efficacité de l'ingénierie de contraintes dans les nanofils jusqu'à de faibles longueurs de grilles (~17nm). Des mesures de bruit basse fréquence ont été réalisées sur ces mêmes dispositifs et analysées en fonction des paramètres géométriques de l'architecture nanofils (largeur W, forme de la section, longueur de grille L), et des diverses variantes technologiques. Nous avons démontré que le bruit 1/f dans les transistors nanofils peut être décrit par le modèle de fluctuations du nombre de porteurs (CNF) corrélées aux fluctuations de mobilité (CMF). Le bruit associé aux régions S/D a pu également être intégré dans ce modèle en ajoutant une contribution, en particulier pour les PMOS. Alors que les différentes variantes technologiques ont peu d'effet sur le bruit 1/f, les variations de géométrie en L et W changent la composante de bruit liée aux fluctuations du nombre de porteurs (CNF) de manière inversement proportionnelle à la surface totale (~1/WL). Cette augmentation du bruit est le reflet du transport qui se produit à proximité des interfaces avec l'oxyde. Les différentes orientations des interfaces supérieures et latérales (110) ou (100) présentent la même quantité de pièges d'interface (extrait à partir des mesures de bruit 1/f, en séparant les contributions des différentes faces du nanofil) bien qu'ayant une rugosité différente essentiellement liée au process. En revanche la composante CMF n'est pas altérée par la réduction des dimensions contrairement à la mobilité des porteurs qui décroit fortement avec L. Finalement, les mesures de bruit 1/f ont été comparées aux spécifications ITRS 2013 pour les transistors multi-grilles en vue des futurs nœuds technologiques de la logique CMOS, et démontrent que nos transistors nanofils satisfont les exigences en la matière

III-V Nanowire MOSFET High-Frequency Technology Platform

This thesis addresses the main challenges in using III-V nanowireMOSFETs for high-frequency applications by building a III-Vvertical nanowire MOSFET technology library. The initial devicelayout is designed, based on the assessment of the current III-V verticalnanowire MOSFET with state-of-the-art performance. The layout providesan option to scale device dimensions for the purpose of designing varioushigh-frequency circuits. The nanowire MOSFET device is described using1D transport theory, and modeled with a compact virtual source model.Device assessment is performed at high frequencies, where sidewall spaceroverlaps have been identified and mitigated in subsequent design iterations.In the final stage of the design, the device is simulated with fT > 500 GHz,and fmax > 700 GHz.Alongside the III-V vertical nanowire device technology platform, adedicated and adopted RF and mm-wave back-end-of-line (BEOL) hasbeen developed. Investigation into the transmission line parameters revealsa line attenuation of 0.5 dB/mm at 50 GHz, corresponding to state-ofthe-art values in many mm-wave integrated circuit technologies. Severalkey passive components have been characterized and modeled. The deviceinterface module - an interconnect via stack, is one of the prominentcomponents. Additionally, the approach is used to integrate ferroelectricMOS capacitors, in a unique setting where their ferroelectric behavior iscaptured at RF and mm-wave frequencies.Finally, circuits have been designed. A proof-of-concept circuit, designedand fabricated with III-V lateral nanowire MOSFETs and mm-wave BEOL, validates the accuracy of the BEOL models, and the circuit design. Thedevice scaling is shown to be reflected into circuit performance, in aunique device characterization through an amplifier noise-matched inputstage. Furthermore, vertical-nanowire-MOSFET-based circuits have beendesigned with passive feedback components that resonate with the devicegate-drain capacitance. The concept enables for device unilateralizationand gain boosting. The designed low-noise amplifiers have matching pointsindependent on the MOSFET gate length, based on capacitance balancebetween the intrinsic and extrinsic capacitance contributions, in a verticalgeometry. The proposed technology platform offers flexibility in device andcircuit design and provides novel III-V vertical nanowire MOSFET devicesand circuits as a viable option to future wireless communication systems

Electrical Characterisation of III-V Nanowire MOSFETs

The ever increasing demand for faster and more energy-efficient electricalcomputation and communication presents severe challenges for the semiconductor industry and particularly for the metal-oxidesemiconductorfield-effect transistor (MOSFET), which is the workhorse of modern electronics. III-V materials exhibit higher carrier mobilities than the most commonly used MOSFET material Si so that the realisation of III-V MOSFETs can enable higher operation speeds and lower drive voltages than that which is possible in Si electronics. A lowering of the transistor drive voltage can be further facilitated by employing gate-all-around nanowire geometries or novel operation principles. However, III-V materials bring about their own challenges related to material quality and to the quality of the gate oxide on top of a III-V MOSFET channel.This thesis presents detailed electrical characterisations of two types of (vertical) III-V nanowire transistors: MOSFETs based on conventional thermionic emission; and Tunnel FETs, which utilise quantum-mechanical tunnelling instead to control the device current and reach inverse subthreshold slopes below the thermal limit of 60 mV/decade. Transistor characterisations span over fourteen orders of magnitude in frequency/time constants and temperatures from 11 K to 370 K.The first part of the thesis focusses on the characterisation of electrically active material defects (‘traps’) related to the gate stack. Low-frequency noise measurements yielded border trap densities of 10^18 to 10^20 cm^-3 eV^-1 and hysteresis measurements yielded effective trap densities – projected to theoxide/semiconductor interface – of 2x10^12 to 3x10^13 cm^-2 eV^-1. Random telegraph noise measurements revealed that individual oxide traps can locally shift the channel energy bands by a few millielectronvolts and that such defects can be located at energies from inside the semiconductor band gap all the way into the conduction band.Small-signal radio frequency (RF) measurements revealed that parts of the wide oxide trap distribution can still interact with carriers in the MOSFET channel at gigahertz frequencies. This causes frequency hystereses in the small-signal transconductance and capacitances and can decrease the RF gains by a few decibels. A comprehensive small-signal model was developed, which takes into account these dispersions, and the model was applied to guide improvements of the physical structure of vertical RF MOSFETs. This resulted in values for the cutoff frequency fT and the maximum oscillation frequency fmax of about 150 GHz in vertical III-V nanowire MOSFETs.Bias temperature instability measurements and the integration of (lateral) III-V nanowire MOSFETs in a back end of line process were carried out as complements to the main focus of this thesis. The results of this thesis provide a broad perspective of the properties of gate oxide traps and of the RF performance of III-V nanowire transistors and can act as guidelines for further improvement and finally the integration of III-V nanowire MOSFETs in circuits

Radio Frequency InGaAs MOSFETs

III-V-based Indium gallium arsenide is a promising channel material for high-frequency applications due to its superior electron mobility property. In this thesis, InGaAs/InP heterostructure radio frequency MOSFETs are designed, fabricated, and characterized. Various spacer technologies, from high dielectric spacers to air spacers, are implemented to reduce parasitic capacitances, and fT/fmax are evaluated. Three types of RF MOSFETs with different spacer technologies are fabricated in this work.InP ∧-ridge spacers are integrated on InGaAs Nanowire MOSFET in an attempt to decrease parasitic capacitances; however, due to a high-dielectric constant of the spacers and smaller transistors transconductance, the fT/fmax are limited to 75/100 GHz. InGaAs quantum well MOSFETs with a sacrificial amorphous silicon spacer are fabricated, and they have capacitances of a similar magnitude to other existing high-performing RF InGaAs FETs. An 80 nm InGaAs MOSFET has fT/fmax = 243/147 GHz is demonstrated, and further optimization of the channel and layout would improve the performance. Next, InGaAs MOSFETs with nitride spacer are fabricated in a top-down approach, where the heterostructure is designed to reduce contact resistance and thus improve transconductance. In the first attempt, from the electrical characterization, it is concluded that the ON resistance of these MOSFETs is comparable to state-of-the-art HEMTs. Complete non-quasi-static small-signal modeling is performed on these transistors, and the discrepancy in the magnitude of fmax is discussed. InGaAs/InP 3D-nanosheet/nanowire FETs' high-frequency performance is studied by combining intrinsic analytical and extrinsic numerical models to estimate fT/fmax. 3D vertical stacking results in smaller parasitic capacitances due to electric field perturbance because of screening.An 8-band k⋅p model is implemented to calculate the electronic parameters of strained InxGa1-xAs/InP heterostructure-based quantum wells and nanowires. Bandgap, conduction band energy levels, and their effective masses and non-parabolicity factors are studied for various indium compositions and channel dimensions. These calculated parameters are used to model the long channel quantum well InGaAs MOSFET at cryogenic temperatures, and the importance of band tails limiting the subthreshold slope is discussed

Electrical characterization and modeling of low dimensional nanostructure FET

At the beginning of this thesis, basic and advanced device fabrication process which I haveexperienced during study such as top-down and bottom-up approach for the nanoscale devicefabrication technique have been described. Especially, lithography technology has beenfocused because it is base of the modern device fabrication. For the advanced device structure,etching technique has been investigated in detail.The characterization of FET has been introduced. For the practical consideration in theadvanced FET, several parameter extraction techniques have been introduced such as Yfunction,split C-V etc.FinFET is one of promising alternatives against conventional planar devices. Problem ofFinFET is surface roughness. During the fabrication, the etching process induces surfaceroughness on the sidewall surfaces. Surface roughness of channel decreases the effectivemobility by surface roughness scattering. With the low temperature measurement andmobility analysis, drain current through sidewall and top surface was separated. From theseparated currents, effective mobilities were extracted in each temperature conditions. Astemperature lowering, mobility behaviors from the transport on each surface have differenttemperature dependence. Especially, in n-type FinFET, the sidewall mobility has strongerdegradation in high gate electric field compare to top surface. Quantification of surfaceroughness was also compared between sidewall and top surface. Low temperaturemeasurement is nondestructive characterization method. Therefore this study can be a propersurface roughness measurement technique for the performance optimization of FinFET.As another quasi-1 D nanowire structure device, 3D stacked SiGe nanowire has beenintroduced. Important of strain engineering has been known for the effective mobility booster.The limitation of dopant diffusion by strain has been shown. Without strain, SiGe nanowireFET showed huge short channel effect. Subthreshold current was bigger than strained SiGechannel. Temperature dependent mobility behavior in short channel unstrained device wascompletely different from the other cases. Impurity scattering was dominant in short channelunstrained SiGe nanowire FET. Thus, it could be concluded that the strain engineering is notnecessary only for the mobility booster but also short channel effect immunity.Junctionless FET is very recently developed device compare to the others. Like as JFET,junctionless FET has volume conduction. Thus, it is less affected by interface states.Junctionless FET also has good short channel effect immunity because off-state ofjunctionless FET is dominated pinch-off of channel depletion. For this, junctionless FETshould have thin body thickness. Therefore, multi gate nanowire structure is proper to makejunctionless FET.Because of the surface area to volume ratio, quasi-1D nanowire structure is good for thesensor application. Nanowire structure has been investigated as a sensor. Using numericalsimulation, generation-recombination noise property was considered in nanowire sensor.Even though the surface area to volume ration is enhanced in the nanowire channel, devicehas sensing limitation by noise. The generation-recombination noise depended on the channelgeometry. As a design tool of nanowire sensor, noise simulation should be carried out toescape from the noise limitation in advance.The basic principles of device simulation have been discussed. Finite difference method andMonte Carlo simulation technique have been introduced for the comprehension of devicesimulation. Practical device simulation data have been shown for examples such as FinFET,strongly disordered 1D channel, OLED and E-paper.At the beginning of this thesis, basic and advanced device fabrication process which I haveexperienced during study such as top-down and bottom-up approach for the nanoscale devicefabrication technique have been described. Especially, lithography technology has beenfocused because it is base of the modern device fabrication. For the advanced device structure,etching technique has been investigated in detail.The characterization of FET has been introduced. For the practical consideration in theadvanced FET, several parameter extraction techniques have been introduced such as Yfunction,split C-V etc.FinFET is one of promising alternatives against conventional planar devices. Problem ofFinFET is surface roughness. During the fabrication, the etching process induces surfaceroughness on the sidewall surfaces. Surface roughness of channel decreases the effectivemobility by surface roughness scattering. With the low temperature measurement andmobility analysis, drain current through sidewall and top surface was separated. From theseparated currents, effective mobilities were extracted in each temperature conditions. Astemperature lowering, mobility behaviors from the transport on each surface have differenttemperature dependence. Especially, in n-type FinFET, the sidewall mobility has strongerdegradation in high gate electric field compare to top surface. Quantification of surfaceroughness was also compared between sidewall and top surface. Low temperaturemeasurement is nondestructive characterization method. Therefore this study can be a propersurface roughness measurement technique for the performance optimization of FinFET.As another quasi-1 D nanowire structure device, 3D stacked SiGe nanowire has beenintroduced. Important of strain engineering has been known for the effective mobility booster.The limitation of dopant diffusion by strain has been shown. Without strain, SiGe nanowireFET showed huge short channel effect. Subthreshold current was bigger than strained SiGechannel. Temperature dependent mobility behavior in short channel unstrained device wascompletely different from the other cases. Impurity scattering was dominant in short channelunstrained SiGe nanowire FET. Thus, it could be concluded that the strain engineering is notnecessary only for the mobility booster but also short channel effect immunity.Junctionless FET is very recently developed device compare to the others. Like as JFET,junctionless FET has volume conduction. Thus, it is less affected by interface states.Junctionless FET also has good short channel effect immunity because off-state ofjunctionless FET is dominated pinch-off of channel depletion. For this, junctionless FETshould have thin body thickness. Therefore, multi gate nanowire structure is proper to makejunctionless FET.Because of the surface area to volume ratio, quasi-1D nanowire structure is good for thesensor application. Nanowire structure has been investigated as a sensor. Using numericalsimulation, generation-recombination noise property was considered in nanowire sensor.Even though the surface area to volume ration is enhanced in the nanowire channel, devicehas sensing limitation by noise. The generation-recombination noise depended on the channelgeometry. As a design tool of nanowire sensor, noise simulation should be carried out toescape from the noise limitation in advance.The basic principles of device simulation have been discussed. Finite difference method andMonte Carlo simulation technique have been introduced for the comprehension of devicesimulation. Practical device simulation data have been shown for examples such as FinFET,strongly disordered 1D channel, OLED and E-paper.SAVOIE-SCD - Bib.électronique (730659901) / SudocGRENOBLE1/INP-Bib.électronique (384210012) / SudocGRENOBLE2/3-Bib.électronique (384219901) / SudocSudocFranceF

Strain-Engineered MOSFETs

This book brings together new developments in the area of strain-engineered MOSFETs using high-mibility substrates such as SIGe, strained-Si, germanium-on-insulator and III-V semiconductors into a single text which will cover the materials aspects, principles, and design of advanced devices, their fabrication and applications. The book presents a full TCAD methodology for strain-engineering in Si CMOS technology involving data flow from process simulation to systematic process variability simulation and generation of SPICE process compact models for manufacturing for yield optimization

A study of silicon and germanium junctionless transistors

Technology boosters, such as strain, HKMG and FinFET, have been introduced into semiconductor industry to extend Moore’s law beyond 130 nm technology nodes. New device structures and channel materials are highly demanded to keep performance enhancement when the device scales beyond 22 nm. In this work, the properties and feasibility of the proposed Junctionless transistor (JNT) have been evaluated for both Silicon and Germanium channels. The performance of Silicon JNTs with 22 nm gate length have been characterized at elevated temperature and stressed conditions. Furthermore, steep Subthreshold Slopes (SS) in JNT and IM devices are compared. It is observed that the floating body in JNT is relatively dynamic comparing with that in IM devices and proper design of the device structure may further reduce the VD for a sub- 60 mV/dec subthreshold slope. Diode configuration of the JNT has also been evaluated, which demonstrates the first diode without junctions. In order to extend JNT structure into the high mobility material Germanium (Ge), a full process has been develop for Ge JNT. Germanium-on-Insulator (GeOI) wafers were fabricated using Smart-Cut with low temperature direct wafer bonding method. Regarding the lithography and pattern transfer, a top-down process of sub-50-nm width Ge nanowires is developed in this chapter and Ge nanowires with 35 nm width and 50 nm depth are obtained. The oxidation behaviour of Ge by RTO has been investigated and high-k passivation scheme using thermally grown GeO2 has been developed. With all developed modules, JNT with Ge channels have been fabricated by the CMOScompatible top-down process. The transistors exhibit the lowest subthreshold slope to date for Ge JNT. The devices with a gate length of 3 μm exhibit a SS of 216 mV/dec with an ION/IOFF current ratio of 1.2×103 at VD = -1 V and DIBL of 87 mV/V

Multigate MOSFETs for digital performance and high linearity, and their fabrication techniques

The aggressive downscaling of complementary metal–oxide–semiconductor (CMOS) technology is facing great challenges to overcome severe short-channel effects. Multigate MOSFETs are one of the most promising candidates for scaling beyond Si CMOS, due to better electrostatic control as compared to conventional planar MOSFETs. Conventional dry etching-induced surface damage is one of the main sources of performance degradation for multigate transistors, especially for III-V high mobility materials. It is also challenging to increase the fin aspect ratio by dry etching because of the non-ideal anisotropic etching profile. Here, we report a novel method, inverse metal-assisted chemical etching (i-MacEtch), in lieu of conventional RIE etching, for 3D fin channel formation. InP junctionless FinFETs with record high-aspect-ratio (~ 50:1) fins are demonstrated by this method for the first time. The i-MacEtch process flow eliminates dry-etching-induced plasma damage, high energy ion implantation damage, and high temperature annealing, allowing for the fabrication of InP fin channels with atomically smooth sidewalls. The sidewall features resulting from this unique and simplified process ensure high interface quality between high-k dielectric layer and InP fin channel. Experimental and theoretical analyses show that high-aspect-ratio FinFETs, which could deliver more current per area under much relaxed horizontal geometry requirements, are promising in pushing the technology node ahead where conventional scaling has met its physical limits. The performance of the FinFET was further investigated through numerical simulation. A new kind of FinFET with asymmetric gate and source/drain contacts has been proposed and simulated. By benchmarking with conventional symmetric FinFET, better short-channel behavior with much higher current density is confirmed. The design guidelines are provided. The overall circuit delay can be minimized by optimizing gate lengths according to different local parasites among circuits in interconnection-delay-dominated SoC applications. Continued transistor scaling requires even stronger gate electrostatic control over the channel. The ultimate scaling structure would be gate-all-around nanowire MOSFETs. We demonstrate III-V junctionless gate-all-around (GAA) nanowire (NW) MOSFETs for the first time. For the first time, source/drain (S/D) resistance and thermal budget are minimized by regrowth using metalorganic chemical vapor deposition (MOCVD) in III-V MOSFETs. The fabricated short-channel (Lg=80 nm) GaAs GAA NWFETs with extremely narrow nanowire width (WNW= 9 nm) show excellent transconductance (gm) linearity at biases (300 mV), characterized by the high third intercept point (2.6 dBm). The high linearity is especially important for low power applications because it is insensitive to bias conditions