Scaling and process effect on electromigration reliability for Cu/low k interconnects

textThe microelectronics industry has been managing the RC delay problem arising from aggressive line scaling, by replacing aluminum (Al) by copper (Cu) and oxide dielectric by low-k dielectric. Electromigration (EM) turned out to be a serious reliability problem for Cu interconnects due to the implementation of mechanically weaker low-k dielectrics. In addition, line width and via size scaling resulted in the need of a novel diffusion barrier, which should be uniform and thin. The objective of this dissertation is to investigate the impacts of Ta barrier process, such as barrier-first and pre-clean first, and scaling of barrier and line/via on EM reliability of Cu/low-k interconnects. For this purpose, EM statistical test structures, having different number of line segments, line width, and via width, were designed. The EM test structures were fabricated by a dualdamascene process with two metal layers (M1/Via/M2), which were then packaged for EM tests. The package-level EM tests were performed in a specially designed vacuum chamber with pure nitrogen environment. The novel barrier deposition process, called barrier-first, showed a higher (jL)[subscript c] product and prolonged EM lifetime, compared with the conventional Ta barrier deposition process, known as pre-clean first. This can be attributed to the improved uniformity and thickness of the Ta layer on the via and trench, as confirmed by TEM. As for the barrier thickness effect, the (jL)c product decreased with decreasing thickness, due to reduced Cu confinement. A direct correlation between via size and EM reliability was found; namely, EM lifetime and statistics degraded with via size. This can be attributed to the fact that critical void length to cause open circuit is about the size of via width. To investigate further line scaling effect on EM reliability, SiON (siliconoxynitride) trenchfilling process was introduced to fabricate 60-nm lines, corresponding to 45-nm technology, using a conventional, wider line lithograph technology. The EM lifetime of 60-nm fine lines with SiON filling was longer than that of a standard damascene structure, which can be attributed to a distinct via/metal-1 configuration in reducing process-induced defects at the via/metal-1 interface.Materials Science and Engineerin

Copper Metal for Semiconductor Interconnects

Resistance-capacitance (RC) delay produced by the interconnects limits the speed of the integrated circuits from 0.25 mm technology node. Copper (Cu) had been used to replace aluminum (Al) as an interconnecting conductor in order to reduce the resistance. In this chapter, the deposition method of Cu films and the interconnect fabrication with Cu metallization are introduced. The resulting integration and reliability challenges are addressed as well

Effects of scaling on microstructure evolution of Cu nanolines and impact on electromigration reliability

textScaling can significantly degrade the electromigration (EM) lifetime for Cu interconnects, raising serious reliability concerns. Different methods have emerged to enhance the EM resistance of Cu by suppressing the interface diffusion (the historically fastest diffusion path), notably using CoWP metal cap and Mn alloying. With further scaling of Cu interconnects, EM reliability becomes increasingly complex due to changes in Cu microstructure. In ultra-fine Cu lines a large population of small grains mix with bamboo-type grains, resulting in an additional contribution of grain boundary diffusion to EM degradation. With the interface diffusion suppressed by CoWP or Mn alloying, the grain structure effect becomes even more important. The objective of this study is to investigate the EM reliability of ultra-fine Cu interconnects, focusing on the scaling effect on grain structure and mass transport. First, the detailed microstructure information of Cu interconnects down to the 22 nm node was analyzed using a transmission electron microscope (TEM)-based high resolution diffraction technique. A dominant sidewall growth of {111} grains was observed for 70 nm Cu lines (45 nm node), reflecting the importance of interfacial energy in controlling grain growth. The strength of the {111} texture was found to significantly increase as line width was reduced to 40 nm (22 nm node), while the length fraction of coherent twin boundaries was reduced to ~1%. Secondly, the results from microstructure together with the deduced interfacial and grain boundary diffusivities were used to identify flux divergent sites for void formation and to analyze the grain structure effect on EM statistics using a microstructure-based kinetic model. Finally, based on the analysis of Cu grain structure evolution with downscaling, the scaling behavior of EM drift velocity was investigated for Cu interconnects with CoWP capping and Mn alloying. This enables us to project the EM lifetime and statistics for future technology nodes. The Mn alloying effect on mass transport in combination of grain structure control was found to provide an effective means to improve EM reliability especially with further scaling. In summary, this study establishes a correlation between the microstructure of Cu nanolines, void formation kinetics, and EM statistics.Mechanical Engineerin

Analysis of critical-length data from electromigration failure studies

An accurate estimation of the Blech length, the critical line length below which interconnect lines are immortal, is vital as it allows EDA tools to reduce their workload. In lines longer than the Blech length, either a void will inevitably nucleate and grow until the line fails, or the line will rupture. The majority of failure analyses reveal voiding as the failure mechanism however recent analysis suggest Blech length failures are characterised by simultaneous [6] voiding and rupture, and a non-zero steady-state drift velocity. This paper provides an alternative interpretation of results

Study of initial void formation and electron wind force for scaling effects on electromigration in Cu interconnects

textThe continuing scaling of integrated circuits beyond 22nm technology node poses increasing challenges to Electromigration (EM) reliability for Cu on-chip interconnects. First, the width of Cu lines in advanced technology nodes is less than the electron mean free path which is 39nm in Cu at room temperature. This is a new size regime where any new scaling effect on EM is of basic interest. And second, the reduced line width necessitates the development of new methods to analyze the EM characteristics. Such studies will require the development of well controlled processes to fabricate suitable test structures for EM study and model verification. This dissertation is to address these critical issues for EM in Cu interconnects. The dissertation first studies the initial void growth under EM, which is critical for measurement of the EM lifetime and statistics. A method based on analyzing the resistance traces obtained from EM tests of multi-link structures has been developed. The results indicated that there are three stages in the resistance traces where the rate of the initial void growth in Stage I is lower than that in Stage III after interconnect failure and they are linearly correlated. An analysis extending the Korhonen model has been formulated to account for the initial void formation. In this analysis, the stress evolution in the line during void growth under EM was analyzed in two regions and an analytic solution was deduced for the void growth rate. A Monte Carlo grain growth simulation based on the Potts model was performed to obtain grain structures for void growth analysis. The results from this analysis agreed reasonably well with the EM experiments. The next part of the dissertation is to study the size effect on the electron wind force for a thin film and for a line with a rectangular cross section. The electron wind force was modeled by considering the momentum transfer during collision between electrons and an atom. The scaling effect on the electron wind force was found to be represented by a size factor depending on the film/line dimensions. In general, the electron wind force is enhanced with increasing dimensional confinement. Finally, a process for fabrication of Si nanotrenches was developed for deposition of Cu nanolines with well-defined profiles. A self-aligned sub-lithographic mask technique was developed using polymer residues formed on Si surfaces during reactive ion etching of Si dioxide in a fluorocarbon plasma. This method was capable to fabricate ultra-narrow Si nanotrenches down to 20nm range with rectangular profiles and smooth sidewalls, which are ideal for studying EM damage mechanisms and model verification for future technology nodes.Physic

Diffusivity variation in electromigration failure

Electromigration driven void dynamics plays an important role in the reliability of copper interconnects; a proper understanding of which is made more difficult due to local variations in line microstructure. In simulations, the parameter incorporating these variations best is the effective atomic diffusivity Deff which is sensitive to grain size and orientation, interface layer thickness, etc. We examine a number of experimental results and conclude that, to explain observations using current theoretical models, Deff values must vary significantly along the interconnect, and that such variations are enough to yield encouraging simulations of resistance variations under bidirectional stress

Accelerating Electromigration Aging: Fast Failure Detection for Nanometer ICs

For practical testing and detection of electromigration (EM) induced failures in dual damascene copper interconnects, one critical issue is creating stressing conditions to induce the chip to fail exclusively under EM in a very short period of time so that EM sign-off and validation can be carried out efficiently. Existing acceleration techniques, which rely on increasing temperature and current densities beyond the known limits, also accelerate other reliability effects making it very difficult, if not impossible, to test EM in isolation. In this article, we propose novel EM wear-out acceleration techniques to address the aforementioned issue. First we show that multi-segment interconnects with reservoir and sink structures can be exploited to significantly speedup the EM wear-out process. Based on this observation, we propose three strategies to accelerate EM induced failure: reservoir-enhanced acceleration, sink-enhanced acceleration, and a hybrid method that combines both reservoir and sink structures. We then propose several configurable interconnect structures that exploit atomic reservoirs and sinks for accelerated EM testing. Such configurable interconnect structures are very flexible and can be used to achieve significant lifetime reductions at the cost of some routing resources. Using the proposed technique, EM testing can be carried out at nominal current densities, and at a much lower temperature compared to traditional testing methods. This is the most significant contribution of this work since, to our knowledge, this is the only method that allows EM testing to be performed in a controlled environment without the risk of invoking other reliability effects that are also accelerated by elevated temperature and current density. Simulation results show that, using the proposed method, we can reduce the EM lifetime of a chip from 10 years down to a few hours 10^5X acceleration under the 150C temperature limit, which is sufficient for practical EM testing of typical nanometer CMOS ICs

A survey of carbon nanotube interconnects for energy efficient integrated circuits

This article is a review of the state-of-art carbon nanotube interconnects for Silicon application with respect to the recent literature. Amongst all the research on carbon nanotube interconnects, those discussed here cover 1) challenges with current copper interconnects, 2) process & growth of carbon nanotube interconnects compatible with back-end-of-line integration, and 3) modeling and simulation for circuit-level benchmarking and performance prediction. The focus is on the evolution of carbon nanotube interconnects from the process, theoretical modeling, and experimental characterization to on-chip interconnect applications. We provide an overview of the current advancements on carbon nanotube interconnects and also regarding the prospects for designing energy efficient integrated circuits. Each selected category is presented in an accessible manner aiming to serve as a survey and informative cornerstone on carbon nanotube interconnects relevant to students and scientists belonging to a range of fields from physics, processing to circuit design

Interconnect Aging—Physics to Software

Device reliability or lifetime is often non-negotiable and crucial for sensitive applications such as medical devices, autonomous vehicles and space crafts. Inevitable technology advancement (e.g. miniaturization) has added unwelcome complications and unpredictability to the aging problem. Reliability of VLSI chips is jeopardized by mass transport in metallic interconnects. Material migration is caused by electrical, mechanical and thermal phenomena, and, therefore, is a complicated process. While all aspects of material migration have been studied, a comprehensive investigation that can explain and include all those phenomena simultaneously remains unsolved. Inaccuracies in modeling and predicting aging processes in wires cause that chipmakers often overdesign interconnects. This is an undesirable and expensive approach in terms of time and cost. In modern technologies, the predicted lifetime, aging, and failure mechanisms in interconnect very often do not match the observed behaviors. Unrealistic models used in CAD tools are the main culprit of such incompatibilities. In general, two situations may occur: (1) in some cases, the models may wrongly scrutinize reliability in unfailing parts and consequently impose unnecessary design tightening and (2) in some other cases, the models may underestimate serious reliability problems causing unpredicted behaviors or catastrophic failures to occur. The existing models for reliability evaluation are usually pessimistic in case of interconnect voiding and optimistic when extrusions occur. Time-consuming and not converging reliability assessments, as well as undesired chip behaviors, are the common expensive outcome of such models.We revisit the underlying physics of aging processes in dual-damascene copper lines. We demonstrate, that the simplistic modeling is the cause of the incompatibility of the existing models. We study all three main aging processes: electromigration, thermo-migration, and stress migration and offer several comprehensive yet compact models for realistic assessment of interconnect aging. These models explain many observations that have been inexplicable for decades. Ultimately, a computer-aided design tool, RAIN, is developed based on the proposed models and is capable of assessing the reliability of industry standard complex multi-layer, multi-segment interconnect networks. This tool can be readily integrated into other verification signoffs phases such as performance, timing, and power analyses. RAIN takes as inputs: (1) interconnect design, (2) technology specifications, (3) initial stress and temperature, (4) IR drop and lifetime requirements. It analyzes and assesses reliability and delivery requirements of all nets, and provides a report on voltage limitations, thermal violations and expected lifetime. It is validated on a wide spectrum of experimental results performed on various industry benchmarks