Design of Window Comparators for Integrator-Based Capacitor Array Testing Circuits

This paper investigates the impact of window comparator threshold variations on the performance of integrator-based programmable capacitor array (PCA) testing circuits. It presents two window comparator designs that take different approaches to address the problem of comparator threshold variations in PCA testing. The first comparator design utilizes a fully symmetric circuit structure to achieve small threshold deviations. The second design relies on increasing testing time to reduce the effect of comparator threshold variations. Experimental results are presented to compare the performance of the two design approaches

Low-Overhead Built-In Self-Test for Advanced RF Transceiver Architectures

abstract: Due to high level of integration in RF System on Chip (SOC), the test access points are limited to the baseband and RF inputs/outputs of the system. This limited access poses a big challenge particularly for advanced RF architectures where calibration of internal parameters is necessary and ensure proper operation. Therefore low-overhead built-in Self-Test (BIST) solution for advanced RF transceiver is proposed. In this dissertation. Firstly, comprehensive BIST solution for RF polar transceivers using on-chip resources is presented. In the receiver, phase and gain mismatches degrade sensitivity and error vector magnitude (EVM). In the transmitter, delay skew between the envelope and phase signals and the finite envelope bandwidth can create intermodulation distortion (IMD) that leads to violation of spectral mask requirements. Characterization and calibration of these parameters with analytical model would reduce the test time and cost considerably. Hence, a technique to measure and calibrate impairments of the polar transceiver in the loop-back mode is proposed. Secondly, robust amplitude measurement technique for RF BIST application and BIST circuits for loop-back connection are discussed. Test techniques using analytical model are explained and BIST circuits are introduced. Next, a self-compensating built-in self-test solution for RF Phased Array Mismatch is proposed. In the proposed method, a sinusoidal test signal with unknown amplitude is applied to the inputs of two adjacent phased array elements and measure the baseband output signal after down-conversion. Mathematical modeling of the circuit impairments and phased array behavior indicates that by using two distinct input amplitudes, both of which can remain unknown, it is possible to measure the important parameters of the phased array, such as gain and phase mismatch. In addition, proposed BIST system is designed and fabricated using IBM 180nm process and a prototype four-element phased-array PCB is also designed and fabricated for verifying the proposed method. Finally, process independent gain measurement via BIST/DUT co-design is explained. Design methodology how to reduce performance impact significantly is discussed. Simulation and hardware measurements results for the proposed techniques show that the proposed technique can characterize the targeted impairments accurately.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Programmable photonics : an opportunity for an accessible large-volume PIC ecosystem

We look at the opportunities presented by the new concepts of generic programmable photonic integrated circuits (PIC) to deploy photonics on a larger scale. Programmable PICs consist of waveguide meshes of tunable couplers and phase shifters that can be reconfigured in software to define diverse functions and arbitrary connectivity between the input and output ports. Off-the-shelf programmable PICs can dramatically shorten the development time and deployment costs of new photonic products, as they bypass the design-fabrication cycle of a custom PIC. These chips, which actually consist of an entire technology stack of photonics, electronics packaging and software, can potentially be manufactured cheaper and in larger volumes than application-specific PICs. We look into the technology requirements of these generic programmable PICs and discuss the economy of scale. Finally, we make a qualitative analysis of the possible application spaces where generic programmable PICs can play an enabling role, especially to companies who do not have an in-depth background in PIC technology

Reliable Hardware Architectures of CORDIC Algorithm with Fixed Angle of Rotations

Fixed-angle rotation operation of vectors is widely used in signal processing, graphics, and robotics. Various optimized coordinate rotation digital computer (CORDIC) designs have been proposed for uniform rotation of vectors through known and specified angles. Nevertheless, in the presence of faults, such hardware architectures are potentially vulnerable. In this thesis, we propose efficient error detection schemes for two fixed-angle rotation designs, i.e., the Interleaved Scaling and Cascaded Single-rotation CORDIC. To the best of our knowledge, this work is the first in providing reliable architectures for these variants of CORDIC. The former is suitable for low-area applications and, hence, we propose recomputing with encoded operands schemes which add negligible area overhead to the designs. Moreover, the proposed error detection schemes for the latter variant are optimized for efficient applications which hamper the performance of the architectures negligibly. We present three variants of recomputing with encoded operands to detect both transient and permanent faults, coupled with signature-based schemes. The overheads of the proposed designs are assessed through Xilinx FPGA implementations and their effectiveness is benchmarked through error simulations. The results give confidence for the proposed efficient architectures which can be tailored based on the reliability requirements and the overhead to be tolerated

At-Speed Logic BIST for IP Cores

This paper describes a flexible logic BIST scheme that features high fault coverage achieved by fault-simulation guided test point insertion, real at-speed test capability for multi-clock designs without clock frequency manipulation, and easy physical implementation due to the use of a low-speed SE signal. Application results of this scheme to two widely used IP cores are also reported.Design, Automation and Test in Europe (DATE05), 7-11 March 2005, Munich, German

System Identification, Diagnosis, and Built-In Self-Test of High Switching Frequency DC-DC Converters

abstract: Complex electronic systems include multiple power domains and drastically varying dynamic power consumption patterns, requiring the use of multiple power conversion and regulation units. High frequency switching converters have been gaining prominence in the DC-DC converter market due to smaller solution size (higher power density) and higher efficiency. As the filter components become smaller in value and size, they are unfortunately also subject to higher process variations and worse degradation profiles jeopardizing stable operation of the power supply. This dissertation presents techniques to track changes in the dynamic loop characteristics of the DC-DC converters without disturbing the normal mode of operation. A digital pseudo-noise (PN) based stimulus is used to excite the DC-DC system at various circuit nodes to calculate the corresponding closed-loop impulse response. The test signal energy is spread over a wide bandwidth and the signal analysis is achieved by correlating the PN input sequence with the disturbed output generated, thereby accumulating the desired behavior over time. A mixed-signal cross-correlation circuit is used to derive on-chip impulse responses, with smaller memory and lower computational requirement in comparison to a digital correlator approach. Model reference based parametric and non-parametric techniques are discussed to analyze the impulse response results in both time and frequency domain. The proposed techniques can extract open-loop phase margin and closed-loop unity-gain frequency within 5.2% and 4.1% error, respectively, for the load current range of 30-200mA. Converter parameters such as natural frequency (ω_n ), quality factor (Q), and center frequency (ω_c ) can be estimated within 3.6%, 4.7%, and 3.8% error respectively, over load inductance of 4.7-10.3µH, and filter capacitance of 200-400nF. A 5-MHz switching frequency, 5-8.125V input voltage range, voltage-mode controlled DC-DC buck converter is designed for the proposed built-in self-test (BIST) analysis. The converter output voltage range is 3.3-5V and the supported maximum load current is 450mA. The peak efficiency of the converter is 87.93%. The proposed converter is fabricated on a 0.6µm 6-layer-metal Silicon-On-Insulator (SOI) technology with a die area of 9mm^2 . The area impact due to the system identification blocks including related I/O structures is 3.8% and they consume 530µA quiescent current during operation.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Design for reliability applied to RF-MEMS devices and circuits issued from different TRL environments

Ces travaux de thèse visent à aborder la fiabilité des composants RF-MEMS (commutateurs en particulier) pendant la phase de conception en utilisant différents approches de procédés de fabrication. Ça veut dire que l'intérêt est focalisé en comment éliminer ou diminuer pendant la conception les effets des mécanismes de défaillance plus importants au lieu d'étudier la physique des mécanismes. La détection des différents mécanismes de défaillance est analysée en utilisant les performances RF du dispositif et le développement d'un circuit équivalent. Cette nouvelle approche permet à l'utilisateur final savoir comment les performances vont évoluer pendant le cycle de vie. La classification des procédés de fabrication a été faite en utilisant le Technology Readiness Level du procédé qui évalue le niveau de maturité de la technologie. L'analyse de différentes approches de R&D est décrite en mettant l'accent sur les différences entre les niveaux dans la classification TRL. Cette thèse montre quelle est la stratégie optimale pour aborder la fiabilité en démarrant avec un procédé très flexible (LAAS-CNRS comme exemple de baisse TRL), en continuant avec une approche composant (CEA-Leti comme moyenne TRL) et en finissant avec un procédé standard co-intégré CMOS-MEMS (IHP comme haute TRL) dont les modifications sont impossibles.This thesis is intended to deal with reliability of RF-MEMS devices (switches, in particular) from a designer point of view using different fabrication process approaches. This means that the focus will be on how to eliminate or alleviate at the design stage the effects of the most relevant failure mechanisms in each case rather than studying the underlying physics of failure. The detection of the different failure mechanisms are investigated using the RF performance of the device and the developed equivalent circuits. This novel approach allows the end-user to infer the evolution of the device performance versus time going one step further in the Design for Reliability in RF-MEMS. The division of the fabrication process has been done using the Technology Readiness Level of the process. It assesses the maturity of the technology prior to incorporating it into a system or subsystem. An analysis of the different R&D approaches will be presented by highlighting the differences between the different levels in the TRL classification. This thesis pretend to show how reliability can be improved regarding the approach of the fabrication process starting from a very flexible one (LAAS-CNRS as example of low-TRL) passing through a component approach (CEA-Leti as example of medium-TRL) and finishing with a standard co-integrated CMOS-MEMS process (IHP example of high TRL)

Scalable Approach for Power Droop Reduction During Scan-Based Logic BIST

The generation of significant power droop (PD) during at-speed test performed by Logic Built-In Self Test (LBIST) is a serious concern for modern ICs. In fact, the PD originated during test may delay signal transitions of the circuit under test (CUT): an effect that may be erroneously recognized as delay faults, with consequent erroneous generation of test fails and increase in yield loss. In this paper, we propose a novel scalable approach to reduce the PD during at-speed test of sequential circuits with scan-based LBIST using the launch-on-capture scheme. This is achieved by reducing the activity factor of the CUT, by proper modification of the test vectors generated by the LBIST of sequential ICs. Our scalable solution allows us to reduce PD to a value similar to that occurring during the CUT in field operation, without increasing the number of test vectors required to achieve a target fault coverage (FC). We present a hardware implementation of our approach that requires limited area overhead. Finally, we show that, compared with recent alternative solutions providing a similar PD reduction, our approach enables a significant reduction of the number of test vectors (by more than 50%), thus the test time, to achieve a target FC

Low-overhead fault-tolerant logic for field-programmable gate arrays

While allowing for the fabrication of increasingly complex and efficient circuitry, transistor shrinkage and count-per-device expansion have major downsides: chiefly increased variation, degradation and fault susceptibility. For this reason, design-time consideration of faults will have to be given to increasing numbers of electronic systems in the future to ensure yields, reliabilities and lifetimes remain acceptably high. Many mathematical operators commonly accelerated in hardware are suited to modification resulting in datapath error detection and correction capabilities with far lower area, performance and/or power consumption overheads than those incurred through the utilisation of more established, general-purpose fault tolerance methods such as modular redundancy. Field-programmable gate arrays are uniquely placed to allow further area savings to be made thanks to their dynamic reconfigurability. The majority of the technical work presented within this thesis is based upon a benchmark hardware accelerator---a matrix multiplier---that underwent several evolutions in order to detect and correct faults manifesting along its datapath at runtime. In the first instance, fault detectability in excess of 99% was achieved in return for 7.87% additional area and 45.5% extra latency. In the second, the ability to correct errors caused by those faults was added at the cost of 4.20% more area, while 50.7% of this---and 46.2% of the previously incurred latency overhead---was removed through the introduction of partial reconfiguration in the third. The fourth demonstrates further reductions in both area and performance overheads---of 16.7% and 8.27%, respectively---through systematic data width reduction by allowing errors of less than ±0.5% of the maximum output value to propagate.Open Acces