Development of a MATLAB/Simulink - Arduino environment for experimental practices in control engineering teaching

This project presents the steps followed when implementing a platform based on MATLAB/Simulink and Arduino for the restoration of digital control practices. During this project, an Arduino shield has being designed. Along with this, a web page has also been created where all the material done during all this project is available and can be freely used. So anyone interested on doing a project can have a starting point instead of starting a project from scratch, which most of times this results hard to implement. Taking all this into account, the document is structured in the following manner. The first chapter talks about the hardware used and designed. The second one explains the software used and the configurations done on the laboratory’s PCs. After that, the web page Duino-Based Learning is explained, where you can find the five projects carried out in the "Control Automàtic" subject with their corresponding results. In this section too, as an additional research, the implemented indirect adaptive control will be explained, where the parameter estimation has been done by the Recursive Least Square algorithm. The last four sections before presenting the conclusions of the work, correspond to a satisfaction questionnaire done to the teachers that have used the setup, the costs and saves of the project, the environmental impact and the planning of the project respectively

Design and analysis of feedback controllers for a DC buck-boost converter

In Murdoch University, students majoring in Electrical Power Engineering have the opportunity to learn about the basics of power electronic systems. ENG349 Power Electronic Converters and Systems is a unit where students are exposed to a range of industrial electronics. The power pole board provided by the University of Minnesota is used for laboratory teaching on how DC converters operate [1, 2]. This thesis topic gives an opportunity for Electrical Power students to further expand their basic knowledge on power electronics. Additionally, Instrumentation and Control System Engineering students will have a better understanding of dynamic control systems, which are essential in designing and analysing feedback control on DC converters. Industrial computer systems students are able to design and implement external hardware to enhance power board components. Renewable Energy students will be interested in how DC converters are applied to renewable energy systems. This thesis provides project expansion for all types of electrical engineering majors taught at Murdoch University. The main focus of this thesis is to design and analyse different feedback controllers for the converter system. The literature review and steps into designing feedback controllers are adapted from Ned Mohan’s approach in designing feedback controllers for DC converters [3]. The results presented are based on the author’s knowledge learnt from Electrical Power and Instrumentation and Control Systems Engineering. Computer simulations from Pspice and MATLAB are used for testing the feedback responses of implementing different feedback compensators. The most difficult task in this thesis is to produce accurate results from the power pole board, especially with the peak current controller circuit. Although the simulated results are successful, it is hard to compare these to the experimental results due to the ways of how the power board components are connected. This thesis will further explain the process in exploring these feedback controllers

Integration of an Active Filter and a Single-Phase AC/DC Converter with Reduced Capacitance Requirement and Component Count

Existing methods of incorporating an active filter into an AC/DC converter for eliminating electrolytic capacitors usually require extra power switches. This inevitably leads to an increased system cost and degraded energy efficiency. In this paper, a concept of active-filter integration for single-phase AC/DC converters is reported. The resultant converters can provide simultaneous functions of power factor correction, DC voltage regulation, and active power decoupling for mitigating the low-frequency DC voltage ripple, without an electrolytic capacitor and extra power switch. To complement the operation, two closed-loop voltage-ripple-based reference generation methods are developed for controlling the energy storage components to achieve active power decoupling. Both simulation and experiment have confirmed the eligibility of the proposed concept and control methods in a 210-W rectification system comprising an H-bridge converter with a half-bridge active filter. Interestingly, the end converters (Type I and Type II) can be readily available using a conventional H-bridge converter with minor hardware modification. A stable DC output with merely 1.1% ripple is realized with two 50-μF film capacitors. For the same ripple performance, a 900-μF capacitor is required in conventional converters without an active filter. Moreover, it is found out that the active-filter integration concept might even improve the efficiency performance of the end converters as compared with the original AC/DC converter without integration

Experiment on Bidirectional Single Phase Converter Applying Model Predictive Current Controller

A bidirectional converter able to manage storage is a basic power electronics device, and it is a major component of renewable energy sources, micro grid and also the smart grid concept. In this paper, single-phase bidirectional converter topology is discussed. The state space model has been derived, and a simple model based predictive current controller has been utilized to control the inverter. Control block diagrams have been designed with MATLAB and simulation results are presented and compared with experimental ones, giving credibility to the derived model and the designed control method

Electrical performance characteristics of high power converters for space power applications

The first goal of this project was to investigate various converters that would be suitable for processing electric power derived from a nuclear reactor. The implementation is indicated of a 20 kHz system that includes a source converter, a ballast converter, and a fixed frequency converter for generating the 20 kHz output. This system can be converted to dc simply by removing the fixed frequency converter. This present study emphasized the design and testing of the source and ballast converters. A push-pull current-fed (PPCF) design was selected for the source converter, and a 2.7 kW version of this was implemented using three 900 watt modules in parallel. The characteristic equation for two converters in parallel was derived, but this analysis did not yield any experimental methods for measuring relative stability. The three source modules were first tested individually and then in parallel as a 2.7 kW system. All tests proved to be satisfactory; the system was stable; efficiency and regulation were acceptable; and the system was fault tolerant. The design of a ballast-load converter, which was operated as a shunt regulator, was investigated. The proposed power circuit is suitable for use with BJTs because proportional base drive is easily implemented. A control circuit which minimizes switching frequency ripple and automatically bypasses a faulty shunt section was developed. A nonlinear state-space-averaged model of the shunt regulator was developed and shown to produce an accurate incremental (small-signal) dynamic model, even though the usual state-space-averaging assumptions were not met. The nonlinear model was also shown to be useful for large-signal dynamic simulation using PSpice

Design and Implementation of Control Techniques of Power Electronic Interfaces for Photovoltaic Power Systems

The aim of this thesis is to scrutinize and develop four state-of-the-art power electronics converter control techniques utilized in various photovoltaic (PV) power conversion schemes accounting for maximum power extraction and efficiency. First, Cascade Proportional and Integral (PI) Controller-Based Robust Model Reference Adaptive Control (MRAC) of a DC-DC boost converter has been designed and investigated. Non-minimum phase behaviour of the boost converter due to right half plane zero constitutes a challenge and its non-linear dynamics complicate the control process while operating in continuous conduction mode (CCM). The proposed control scheme efficiently resolved complications and challenges by using features of cascade PI control loop in combination with properties of MRAC. The accuracy of the proposed control system’s ability to track the desired signals and regulate the plant process variables in the most beneficial and optimised way without delay and overshoot is verified. The experimental results and analysis reveal that the proposed control strategy enhanced the tracking speed two times with considerably improved disturbance rejection. Second, (P)roportional Gain (R)esonant and Gain Scheduled (P)roportional (PR-P) Controller has been designed and investigated. The aim of this controller is to create a variable perturbation size real-time adaptive perturb and observe (P&O) maximum power point tracking (MPPT) algorithm. The proposed control scheme resolved the drawbacks of conventional P&O MPPT method associated with the use of constant perturbation size that leads to a poor transient response and high continuous steady-state oscillations. The prime objective of using the PR-P controller is to utilize inherited properties of the signal produced by the controller’s resonant path and integrate it to update best estimated perturbation that represents the working principle of extremum seeking control (ESC) to use in a P&O algorithm that characterizes the overall system learning-based real time adaptive (RTA). Additionally, utilization of internal dynamics of the PR-P controller overcome the challenges namely, complexity, computational burden, implantation cost and slow tracking performance in association with commonly used soft computing intelligent systems and adaptive control strategies. The experimental results and analysis reveal that the proposed control strategy enhanced the tracking speed five times with reduced steady-state oscillations around maximum power point (MPP) and more than 99% energy extracting efficiency.Third, the interleaved buck converter based photovoltaic (PV) emulator current control has been investigated. A proportional-resonant-proportional (PR-P) controller is designed to resolve the drawbacks of conventional PI controllers in terms of phase management which means balancing currents evenly between active phases to avoid thermally stressing and provide optimal ripple cancellation in the presence of parameter uncertainties. The proposed controller shows superior performance in terms of 10 times faster-converging transient response, zero steady-state error with significant reduction in current ripple. Equal load sharing that constitutes the primary concern in multi-phase converters has been achieved with the proposed controller. Implementing of robust control theory involving comprehensive time and frequency domain analysis reveals 13% improvement in the robust stability margin and 12-degree bigger phase toleration with the PR-P controller. Fourth, a symmetrical pole placement Method-based Unity Proportional Gain Resonant and Gain Scheduled Proportional (PR-P) Controller has been designed and investigated. The proposed PR-P controller resolved the issues associated with the use of the PI controller which are tracking repeating control input signal with zero steady-state and mitigating the 3rd order harmonic component injected into the grid for single-phase PV systems. Additionally, the PR-P controller has overcome the drawbacks of frequency detuning in the grid and increase in the magnitude of odd number harmonics in the system that constitute the common concerns in the implementation of conventional PR controller. Moreover, the unprecedented design process based on changing notch filter dynamics with symmetrical pole placement around resonant frequency overcomes the limitations that are essentially complexity and dependency on the precisely modelled system. The verification and validation process of the proposed control schemes has been conducted using MATLAB/Simulink and implementing MATLAB/Simulink/State flow on dSPACE Real-time-interface (RTI) 1007 processor, DS2004 High-Speed A/D and CP4002 Timing and Digital I/O boards

Nonlinear Cascaded Control for a DC-DC Boost Converter

The Boost Converter is a type of DC-DC converter that operates using switching techniques and is designed to elevate the voltage level. This paper presents a cascaded control for a boost converter to ensure that the inductor current and output capacitor voltage remain in a safe operating zone. Ensuring safe operating conditions and stable closed-loop poles is crucial because it guarantees that both current and voltage remain within the designated operating range. This preventive measure prevents any damage to components like capacitors (C), inductors (L), and switches. Unstable operation, on the other hand, could lead to oscillations and an undesirable increase in the amplitude of current and voltage, posing a risk to all components involved. The research contribution involves an investigation of cascaded control, utilizing power and energy concepts due to their advantageous effects on system performance and design. By implementing nonlinear controllers based on a large-signal averaged model, the closed-loop poles remain independent of operating points, eliminating the need for small-signal linearization. Small-signal linearization makes the controlled system dependent on the operating point. Two controllers are introduced based on power and energy concept, which is easy to understand. The potential practical application of the proposed cascaded control approach is in high-power applications. Tracking the energy stored in the output capacitor is first investigated to validate the proposed control scheme by varying the output voltage reference from 32 V to 50 V. Then, the regulation of the energy voltage is explored by varying the load resistance for the output voltage at 50 V. Both are done using a switched model using MATLAB/Simulink software. Simulation results are given to demonstrate the effectiveness of the proposed method. The key metrics used to assess the effectiveness of the proposed control scheme are the undershoot voltage and robustness. The results show that the studied system's tracking, regulating operations and robustness properties are as expected. The proposed method faces a challenge with the number of sensors required. To address this, observers can be utilized to reduce sensor usage while maintaining measurement accuracy. The proposed method can be applied to other power electronic systems