CORDICのハードウェア構成及び応用に関する研究

電気通信大学201

Energy Efficient VLSI Circuits for MIMO-WLAN

Mobile communication - anytime, anywhere access to data and communication services - has been continuously increasing since the operation of the first wireless communication link by Guglielmo Marconi. The demand for higher data rates, despite the limited bandwidth, led to the development of multiple-input multiple-output (MIMO) communication which is often combined with orthogonal frequency division multiplexing (OFDM). Together, these two techniques achieve a high bandwidth efficiency. Unfortunately, techniques such as MIMO-OFDM significantly increase the signal processing complexity of transceivers. While fast improvements in the integrated circuit (IC) technology enabled to implement more signal processing complexity per chip, large efforts had and have to be done for novel algorithms as well as for efficient very large scaled integration (VLSI) architectures in order to meet today's and tomorrow's requirements for mobile wireless communication systems. In this thesis, we will present architectures and VLSI implementations of complete physical (PHY) layer application specific integrated circuits (ASICs) under the constraints imposed by an industrial wireless communication standard. Contrary to many other publications, we do not elaborate individual components of a MIMO-OFDM communication system stand-alone, but in the context of the complete PHY layer ASIC. We will investigate the performance of several MIMO detectors and the corresponding preprocessing circuits, being integrated into the entire PHY layer ASIC, in terms of achievable error-rate, power consumption, and area requirement. Finally, we will assemble the results from the proposed PHY layer implementations in order to enhance the energy efficiency of a transceiver. To this end, we propose a cross-layer optimization of PHY layer and medium access control (MAC) layer

Performance - Complexity Comparison of Receivers for a LTE MIMO–OFDM System

Implementation of receivers for spatial multiplexing multiple-input multiple-output (MIMO) orthogonal-frequency-division-multiplexing (OFDM) systems is considered. The linear minimum mean-square error (LMMSE) and the K-best list sphere detector (LSD) are compared to the iterative successive interference cancellation (SIC) detector and the iterative K-best LSD. The performance of the algorithms is evaluated in 3G long-term evolution (LTE) system. The SIC algorithm is found to perform worse than the K-best LSD when the MIMO channels are highly correlated, while the performance difference diminishes when the correlation decreases. The receivers are designed for 2X2 and 4X4 antenna systems and three different modulation schemes. Complexity results for FPGA and ASIC implementations are found. A modification to the K-best LSD which increases its detection rate is introduced. The ASIC receivers are designed to meet the decoding throughput requirements in LTE and the K-best LSD is found to be the most complex receiver although it gives the best reliable data transmission throughput. The SIC receiver has the best performance–complexity tradeoff in the 2X2 system but in the 4X4 case, the K-best LSD is the most efficient. A receiver architecture which could be reconfigured to using a simple or a more complex detector as the channel conditions change would achieve the best performance while consuming the least amount of power in the receiver

Parallel Searching-Based Sphere Detector for MIMO Downlink OFDM Systems

In this paper, implementation of a detector with parallel partial candidate-search algorithm is described. Two fully independent partial candidate search processes are simultaneously employed for two groups of transmit antennas based on QR decomposition (QRD) and QL decomposition (QLD) of a multiple-input multiple-output (MIMO) channel matrix. By using separate simultaneous candidate searching processes, the proposed implementation of QRD-QLD searching-based sphere detector provides a smaller latency and a lower computational complexity than the original QRD-M detector for similar error-rate performance in wireless communications systems employing four transmit and four receive antennas with 16-QAM or 64-QAM constellation size. It is shown that in coded MIMO orthogonal frequency division multiplexing (MIMO OFDM) systems, the detection latency and computational complexity of a receiver can be substantially reduced by using the proposed QRD-QLD detector implementation. The QRD-QLD-based sphere detector is also implemented using Field Programmable Gate Array (FPGA) and application specific integrated circuit (ASIC), and its hardware design complexity is compared with that of other sphere detectors reported in the literature.Nokia Renesas MobileTexas InstrumentsXilinxNational Science Foundatio

Low complexity MIMO detection algorithms and implementations

University of Minnesota Ph.D. dissertation. December 2014. Major: Electrical Engineering. Advisor: Gerald E. Sobelman. 1 computer file (PDF); ix, 111 pages.MIMO techniques use multiple antennas at both the transmitter and receiver sides to achieve diversity gain, multiplexing gain, or both. One of the key challenges in exploiting the potential of MIMO systems is to design high-throughput, low-complexity detection algorithms while achieving near-optimal performance. In this thesis, we design and optimize algorithms for MIMO detection and investigate the associated performance and FPGA implementation aspects.First, we study and optimize a detection algorithm developed by Shabany and Gulak for a K-Best based high throughput and low energy hard output MIMO detection and expand it to the complex domain. The new method uses simple lookup tables, and it is fully scalable for a wide range of K-values and constellation sizes. This technique reduces the computational complexity, without sacrificing performance and the complexity scales only sub-linearly with the constellation size. Second, we apply the bidirectional technique to trellis search and propose a high performance soft output bidirectional path preserving trellis search (PPTS) detector for MIMO systems. The comparative error analysis between single direction and bidirectional PPTS detectors is given. We demonstrate that the bidirectional PPTS detector can minimize the detection error. Next, we design a novel bidirectional processing algorithm for soft-output MIMO systems. It combines features from several types of fixed complexity tree search procedures. The proposed approach achieves a higher performance than previously proposed algorithms and has a comparable computational cost. Moreover, its parallel nature and fixed throughput characteristics make it attractive for very large scale integration (VLSI) implementation.Following that, we present a novel low-complexity hard output MIMO detection algorithm for LTE and WiFi applications. We provide a well-defined tradeoff between computational complexity and performance. The proposed algorithm uses a much smaller number of Euclidean distance (ED) calculations while attaining only a 0.5dB loss compared to maximum likelihood detection (MLD). A 3x3 MIMO system with a 16QAM detector architecture is designed, and the latency and hardware costs are estimated.Finally, we present a stochastic computing implementation of trigonometric and hyperbolic functions which can be used for QR decomposition and other wireless communications and signal processing applications

Efficient VLSI Implementation of Soft-input Soft-output Fixed-complexity Sphere Decoder

Fixed-complexity sphere decoder (FSD) is one of the most promising techniques for the implementation of multipleinput multiple-output (MIMO) detection, with relevant advantages in terms of constant throughput and high flexibility of parallel architecture. The reported works on FSD are mainly based on software level simulations and a few details have been provided on hardware implementation. The authors present the study based on a four-nodes-per-cycle parallel FSD architecture with several examples of VLSI implementation in 4 × 4 systems with both 16-quadrature amplitude modulation (QAM) and 64-QAM modulation and both real and complex signal models. The implementation aspects and details of the architecture are analysed in order to provide a variety of performance-complexity trade-offs. The authors also provide a parallel implementation of loglikelihood- ratio (LLR) generator with optimised algorithm to enhance the proposed FSD architecture to be a soft-input softoutput (SISO) MIMO detector. To the authors best knowledge, this is the first complete VLSI implementation of an FSD based SISO MIMO detector. The implementation results show that the proposed SISO FSD architecture is highly efficient and flexible, making it very suitable for real application

VLSI Implementation of a Soft-Output Signal Detector for Multi-Mode Adaptive MIMO Systems

This paper presents a multimode soft-output multiple-input multiple-output (MIMO) signal detector that is efficient in hardware cost and energy consumption. The detector is capable of dealing with spatial-multiplexing (SM),break space-division-multiple-access (SDMA), and spatial-diversity (SD) signals of 4 ✕ 4 antenna and 64-QAM modulation. Implementation-friendly algorithms, which reuse most of the mathematical operations in these three MIMO modes, are proposed to provide accurate soft detection information, i.e., log-likelihood ratio, with much reduced complexity. A unified reconfigurable VLSI architecture has been developed to eliminate the implementation of multiple detector modules. In addition, several block level technologies, such as parallel metric update and fast bit-flipping, are adopted to enable a more efficient design. To evaluate the proposed techniques, we implemented the triple-mode MIMO detector in a 65-nm CMOS technology. The core area is 0.25 mm2 with 83.7 K gates. The maximum detecting throughput is 1 Gb/s at 167-MHz clock frequency and 1.2-V supply, which archives the data rate envisioned by the emerging long-term evolution advanced standard. Under frequency-selective channels, the detector consumes 59.3-, 10.5-, and 169.6-pJ energy per bit detection in SM, SD, and SDMA modes, respectively

Rapid Industrial Prototyping and SoC Design of 3G/4G Wireless Systems Using an HLS Methodology

Many very-high-complexity signal processing algorithms are required in future wireless systems, giving tremendous challenges to real-time implementations. In this paper, we present our industrial rapid prototyping experiences on 3G/4G wireless systems using advanced signal processing algorithms in MIMO-CDMA and MIMO-OFDM systems. Core system design issues are studied and advanced receiver algorithms suitable for implementation are proposed for synchronization, MIMO equalization, and detection. We then present VLSI-oriented complexity reduction schemes and demonstrate how to interact these high-complexity algorithms with an HLS-based methodology for extensive design space exploration. This is achieved by abstracting the main effort from hardware iterations to the algorithmic C/C++ fixed-point design. We also analyze the advantages and limitations of the methodology. Our industrial design experience demonstrates that it is possible to enable an extensive architectural analysis in a short-time frame using HLS methodology, which significantly shortens the time to market for wireless systems.National Science Foundatio

Adaptive Baseband Pro cessing and Configurable Hardware for Wireless Communication

The world of information is literally at one’s fingertips, allowing access to previously unimaginable amounts of data, thanks to advances in wireless communication. The growing demand for high speed data has necessitated theuse of wider bandwidths, and wireless technologies such as Multiple-InputMultiple-Output (MIMO) have been adopted to increase spectral efficiency.These advanced communication technologies require sophisticated signal processing, often leading to higher power consumption and reduced battery life.Therefore, increasing energy efficiency of baseband hardware for MIMO signal processing has become extremely vital. High Quality of Service (QoS)requirements invariably lead to a larger number of computations and a higherpower dissipation. However, recognizing the dynamic nature of the wirelesscommunication medium in which only some channel scenarios require complexsignal processing, and that not all situations call for high data rates, allowsthe use of an adaptive channel aware signal processing strategy to provide adesired QoS. Information such as interference conditions, coherence bandwidthand Signal to Noise Ratio (SNR) can be used to reduce algorithmic computations in favorable channels. Hardware circuits which run these algorithmsneed flexibility and easy reconfigurability to switch between multiple designsfor different parameters. These parameters can be used to tune the operations of different components in a receiver based on feedback from the digitalbaseband. This dissertation focuses on the optimization of digital basebandcircuitry of receivers which use feedback to trade power and performance. Aco-optimization approach, where designs are optimized starting from the algorithmic stage through the hardware architectural stage to the final circuitimplementation is adopted to realize energy efficient digital baseband hardwarefor mobile 4G devices. These concepts are also extended to the next generation5G systems where the energy efficiency of the base station is improved.This work includes six papers that examine digital circuits in MIMO wireless receivers. Several key blocks in these receiver include analog circuits thathave residual non-linearities, leading to signal intermodulation and distortion.Paper-I introduces a digital technique to detect such non-linearities and calibrate analog circuits to improve signal quality. The concept of a digital nonlinearity tuning system developed in Paper-I is implemented and demonstratedin hardware. The performance of this implementation is tested with an analogchannel select filter, and results are presented in Paper-II. MIMO systems suchas the ones used in 4G, may employ QR Decomposition (QRD) processors tosimplify the implementation of tree search based signal detectors. However,the small form factor of the mobile device increases spatial correlation, whichis detrimental to signal multiplexing. Consequently, a QRD processor capableof handling high spatial correlation is presented in Paper-III. The algorithm and hardware implementation are optimized for carrier aggregation, which increases requirements on signal processing throughput, leading to higher powerdissipation. Paper-IV presents a method to perform channel-aware processingwith a simple interpolation strategy to adaptively reduce QRD computationcount. Channel properties such as coherence bandwidth and SNR are used toreduce multiplications by 40% to 80%. These concepts are extended to usetime domain correlation properties, and a full QRD processor for 4G systemsfabricated in 28 nm FD-SOI technology is presented in Paper-V. The designis implemented with a configurable architecture and measurements show thatcircuit tuning results in a highly energy efficient processor, requiring 0.2 nJ to1.3 nJ for each QRD. Finally, these adaptive channel-aware signal processingconcepts are examined in the scope of the next generation of communicationsystems. Massive MIMO systems increase spectral efficiency by using a largenumber of antennas at the base station. Consequently, the signal processingat the base station has a high computational count. Paper-VI presents a configurable detection scheme which reduces this complexity by using techniquessuch as selective user detection and interpolation based signal processing. Hardware is optimized for resource sharing, resulting in a highly reconfigurable andenergy efficient uplink signal detector

An adaptive detector implementation for MIMO-OFDM downlink

Cognitive radio (CR) systems require flexible and adaptive implementations of signal processing algorithms. An adaptive symbol detector is needed in the baseband receiver chain to achieve the desired flexibility of a CR system. This paper presents a novel design of an adaptive detector as an application-specific instruction-set processor (ASIP). The ASIP template is based on transport triggered architecture (TTA). The processor architecture is designed in such a manner that it can be programmed to support different suboptimal multiple-input multiple-output (MIMO) detection algorithms in a single TTA processor. The linear minimum mean-square error (LMMSE) and three variants of the selective spanning for fast enumeration (SSFE) detection algorithms are considered. The detection algorithm can be switched between the LMMSE and SSFE according to the bit error rate (BER) performance requirement in the TTA processor. The design can be scaled for different antenna configurations and different modulations. Some of the algorithm architecture co-optimization techniques used here are also presented. Unlike most other detector ASIPs, high level language is used to program the processor to meet the time-to-market requirements. The adaptive detector delivers 4.88 - 49.48 Mbps throughput at a clock frequency of 200 MHz on 90 nm technology