Characterization and Implementation of Fault-Tolerant Vertical Links for 3-D Networks-on-Chip

Through silicon vias (TSVs) provide an efficient way to support vertical communication among different layers of a vertically stacked chip, enabling scalable 3-D networks-on-chip (NoC) architectures. Unfortunately, low TSV yields significantly impact the feasibility of high-bandwidth vertical connectivity. In this paper, we present a semi-automated design flow for 3-D NoCs including a defect-tolerance scheme to increase the global yield of 3-D stacked chips. Starting from an accurate physical and geometrical model of TSVs: 1) we extract a circuit-level model for vertical interconnections; 2) we use it to evaluate the design implications of extending switch architectures with ports in the vertical direction; moreover, 3) we present a defect-tolerance technique for TSV-based multi-bit links through an effective use of redundancy; and finally, 4) we present a design flow allowing for post-layout simulation of NoCs with links in all three physical dimensions. Experimental results show that a 3-D NoC implementation yields around 10% frequency improvement over a 2-D one, thanks to the propagation delay advantage of TSVs and the shorter links. In addition, the adopted fault tolerance scheme demonstrates a significant yield improvement, ranging from 66% to 98%, with a low area cost (20.9% on a vertical link in a NoC switch, which leads a modest 2.1% increase in the total switch area) in 130 nm technology, with minimal impact on very large-scale integrated design and test flows

Trough-silicon-via inductor: Is it real or just a fantasy?

Through-silicon-vias (TSVs) can potentially be used to implement inductors in three-dimensional (3D) integrated system for minimal footprint and large inductance. However, different from conventional 2D spiral inductor, TSV inductors are buried in lossy substrate, thus suffering from low quality factors. This thesis presents how various process and design parameters affect their performance. A few interesting phenomena that are unique to TSV inductors are observed. We then proposed a novel shield mechanism utilizing the micro-channel, a technique conventionally used for heat removal, to reduce the substrate loss. The technique increases the quality factor and inductance of the TSV inductor by up to 21x and 17x respectively. It enables us to implement TSV inductors of up to 38x smaller area and 33% higher quality factor, compared with spiral inductors of the same inductance. To the best of the authors\u27 knowledge, this is the very first in-depth study on TSV inductors. We hope our study shall point out a new and exciting research direction for 3D IC designers --Abstract, page iii

Green on-chip inductors in three-dimensional integrated circuits

This thesis focuses on the technique for the improvement of quality factor and inductance of the TSV inductors and then on the utilization of TSV inductors in various on-chip applications such as DC-DC converter and resonant clocking. Through-silicon-vias (TSVs) are the enabling technique for three-dimensional integrated circuits (3D ICs). However, their large area significantly reduces the benefits that can be obtained by 3D ICs. On the other hand, a major limiting factor for the implementation of many on-chip circuits such as DC-DC converters and resonant clocking is the large area overhead induced by spiral inductors. Several works have been proposed in the literature to make inductors out of idle TSVs. In this thesis, the technique to improve the quality factor and inductance is proposed and then discusses about two applications utilizing TSV inductors i.e., inductive DC-DC converters and LC resonant clocking. The TSV inductor performs inferior to spiral inductors due to its increases losses. Hence to improve the performance of the TSV inductor, the losses should be reduced. Inductive DC-DC converters become prominent for on-chip voltage conversion because of their high efficiency compared with other types of converters (e.g. linear and capacitive converters). On the other hand, to reduce on-chip power, LC resonant clocking has become an attractive option due to its same amplitude and phases compared to other resonant clocking methods such as standing wave and rotary wave. A major challenge for both applications is associated with the required inductor area. In this thesis, the effectiveness of such TSV inductors in addressing both challenges are demonstrated --Abstract, page iv

Cost-Effective Design of Mesh-of-Tree Interconnect for Multi-Core Clusters with 3-D Stacked L2 Scratchpad Memory

3-D integrated circuits (3-D ICs) offer a promising solution to overcome the scaling limitations of 2-D ICs. However, using too many through-silicon-vias (TSVs) pose a negative impact on 3-D ICs due to the large overhead of TSV (e.g., large footprint and low yield). In this paper, we propose a new TSV sharing method for a circuit-switched 3-D mesh-of-tree (MoT) interconnect, which supports high-throughput and low-latency communication between processing cores and 3-D stacked multibanked L2 scratchpad memory. The proposed method supports traffic balancing and TSV-failure tolerant routing. The proposed method advocates a modular design strategy to allow stacking multiple identical memory dies without the need for different masks for dies at different levels in the memory stack. We also investigate various parameters of 3-D memory stacking (e.g., fabrication technology, TSV bonding technique, number of memory tiers, and TSV sharing scheme) that affect interconnect latency, system performance, and fabrication cost. Compared to conventional MoT interconnect that is straightforwardly adapted to 3-D integration, the proposed method yields up to (times 2.11) and (times 1.11) improvements in terms of cost efficiency (i.e., performance/cost) for microbump TSV bonding and direct Cu–Cu TSV bonding techniques, respectively

Characterization and Implementation of Fault-Tolerant Vertical Links for 3-D Networks-on-Chip

Through silicon vias (TSVs) provide an efficient way to support vertical communication among different layers of a vertically stacked chip, enabling scalable 3-D networks-on-chip (NoC) architectures. Unfortunately, low TSV yields significantly impact the feasibility of high-bandwidth vertical connectivity. In this paper, we present a semi-automated design flow for 3-D NoCs including a defect-tolerance scheme to increase the global yield of 3-D stacked chips. Starting from an accurate physical and geometrical model of TSVs: 1) we extract a circuit-level model for vertical interconnections; 2) we use it to evaluate the design implications of extending switch architectures with ports in the vertical direction; moreover, 3) we present a defect-tolerance technique for TSV-based multi-bit links through an effective use of redundancy; and finally, 4) we present a design flow allowing for post-layout simulation of NoCs with links in all three physical dimensions. Experimental results show that a 3-D NoC implementation yields around 10% frequency improvement over a 2-D one, thanks to the propagation delay advantage of TSVs and the shorter links. In addition, the adopted fault tolerance scheme demonstrates a significant yield improvement, ranging from 66% to 98%, with a low area cost (20.9% on a vertical link in a NoC switch, which leads a modest 2.1% increase in the total switch area) in 130 nm technology, with minimal impact on very large-scale integrated design and test flows

Enabling Technologies for 3D ICs: TSV Modeling and Analysis

Through silicon via (TSV) based three-dimensional (3D) integrated circuit (IC) aims to stack and interconnect dies or wafers vertically. This emerging technology offers a promising near-term solution for further miniaturization and the performance improvement of electronic systems and follows a more than Moore strategy. Along with the need for low-cost and high-yield process technology, the successful application of TSV technology requires further optimization of the TSV electrical modeling and design. In the millimeter wave (mmW) frequency range, the root mean square (rms) height of the TSV sidewall roughness is comparable to the skin depth and hence becomes a critical factor for TSV modeling and analysis. The impact of TSV sidewall roughness on electrical performance, such as the loss and impedance alteration in the mmW frequency range, is examined and analyzed following the second order small perturbation method. Then, an accurate and efficient electrical model for TSVs has been proposed considering the TSV sidewall roughness effect, the skin effect, and the metal oxide semiconductor (MOS) effect. However, the emerging application of 3D integration involves an advanced bio-inspired computing system which is currently experiencing an explosion of interest. In neuromorphic computing, the high density membrane capacitor plays a key role in the synaptic signaling process, especially in a spike firing analog implementation of neurons. We proposed a novel 3D neuromorphic design architecture in which the redundant and dummy TSVs are reconfigured as membrane capacitors. This modification has been achieved by taking advantage of the metal insulator semiconductor (MIS) structure along the sidewall, strategically engineering the fixed oxide charges in depletion region surrounding the TSVs, and the addition of oxide layer around the bump without changing any process technology. Without increasing the circuit area, these reconfiguration of TSVs can result in substantial power consumption reduction and a significant boost to chip performance and efficiency. Also, depending on the availability of the TSVs, we proposed a novel CAD framework for TSV assignments based on the force-directed optimization and linear perturbation

3D modeling and integration of current and future interconnect technologies

Title from PDF of title page viewed June 21, 2021Dissertation advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (pages 133-138)Thesis (Ph.D.)--School of Computing and Engineering and Department of Physics and Astronomy. University of Missouri--Kansas City, 2021To ensure maximum circuit reliability it is very important to estimate the circuit performance and signal integrity in the circuit design phase. A full phase simulation for performance estimation of a large-scale circuit not only require a massive computational resource but also need a lot of time to produce acceptable results. The estimation of performance/signal integrity of sub-nanometer circuits mostly depends on the interconnect capacitance. So, an accurate model for interconnect capacitance can be used in the circuit CAD (computer-aided design) tools for circuit performance estimation before circuit fabrication which reduces the computational resource requirement as well as the time constraints. We propose a new capacitance models for interconnect lines in multilevel interconnect structures by geometrically modeling the electrical flux lines of the interconnect lines. Closed-form equations have been derived analytically for ground and coupling capacitance. First, the capacitance model for a single line is developed, and then the new model is used to derive expressions for the capacitance of a line surrounded by neighboring lines in the same and the adjacent layers above and below. These expressions are simple, and the calculated results are within 10% of Ansys Q3D extracted values. Through silicon via (TSV) is one of the key components of the emerging 3D ICs. However, increasing number of TSVs in smaller silicon area leads to some severe negative impacts on the performance of the 3D IC. Growing signal integrity issues in TSVs is one of the major challenges of 3D integration. In this paper, different materials for the cores of the vias and the interposers are investigated to find the best possible combination that can reduce crosstalk and other losses like return loss and insertion loss in the TSVs. We have explored glass and silicon as interposer materials. The simulation results indicate that glass is the best option as interposer material although silicon interposer has some distinct advantages. For via cores three materials - copper (Cu), tungsten (W) and Cu-W bimetal are considered. From the analysis it can concluded that W would be better for high frequency applications due to lower transmission coefficient. Cu offers higher conductivity, but it has larger thermal expansion coefficient mismatch with silicon. The performance of Cu-W bimetal via would be in between Cu and W. However, W has a thermal expansion coefficient close to silicon. Therefore, bimetal Cu-W based TSV with W as the outer layer would be a suitable option for high frequency 3D IC. Here, we performed the analysis in terms of return loss, transmission coefficient and crosstalk in the vias. Signal speed in current digital systems depends mainly on the delay of interconnects. To overcome this delay problem and keep up with Moore’s law, 3D integrated circuit (vertical integration of multiple dies) with through-silicon via (TSV) has been introduced to ensure much smaller interconnect lengths, and lower delay and power consumption compared to conventional 2D IC technology. Like 2D circuit, the estimation of 3D circuit performance depends on different electrical parameters (capacitance, resistance, inductance) of the TSV. So, accurate modeling of the electrical parameters of the TSV is essential for the design and analysis of 3D ICs. We propose a set of new models to estimate the capacitance, resistance, and inductance of a Cu-filled TSV. The proposed analytical models are derived from the physical shape and the size of the TSV. The modeling approach is comprehensive and includes both the cylindrical and tapered TSVs as well as the bumps. On-chip integration of inductors has always been very challenging. However, for sub- 14nm on-chip applications, large area overhead imposed by the on-chip capacitors and inductors has become a more severe concern. To overcome this issue and ensure power integrity, a novel 3D Through-Silicon-Via (TSV) based inductor design is presented. The proposed TSV based inductor has the potential to achieve both high density and high performance. A new design of a Voltage Controlled Oscillator (VCO) utilizing the TSV based inductor is also presented. The implementation of the VCO is intended to study the feasibility, performance, and real-world application of the proposed TSV based inductor.Introduction -- Background of capacitance modeling of on-chip interconnect -- Accurate modeling of interconnect capacitance in multilevel interconnect structures for sub 22nm technology -- Analysis of different materials and structures for through silicon via and through glass via in 3D integrated circuits -- Impacts of different shapes of through-silicon-via core on 3D IC performance -- Accurate electrical modeling of cu-filled through-silicon-via (TSV) -- Design and characterize TSV based inductor for high frequency voltage-controlled oscillator design -- Conclusion and future wor

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

Interconnect Planning for Physical Design of 3D Integrated Circuits

Vertical stacking—based on modern manufacturing and integration technologies—of multiple 2D chips enables three-dimensional integrated circuits (3D ICs). This exploitation of the third dimension is generally accepted for aiming at higher packing densities, heterogeneous integration, shorter interconnects, reduced power consumption, increased data bandwidth, and realizing highly-parallel systems in one device. However, the commercial acceptance of 3D ICs is currently behind its expectations, mainly due to challenges regarding manufacturing and integration technologies as well as design automation. This work addresses three selected, practically relevant design challenges: (i) increasing the constrained reusability of proven, reliable 2D intellectual property blocks, (ii) planning different types of (comparatively large) through-silicon vias with focus on their impact on design quality, as well as (iii) structural planning of massively-parallel, 3D-IC-specific interconnect structures during 3D floorplanning. A key concept of this work is to account for interconnect structures and their properties during early design phases in order to support effective and high-quality 3D-IC-design flows. To tackle the above listed challenges, modular design-flow extensions and methodologies have been developed. Experimental investigations reveal the effectiveness and efficiency of the proposed techniques, and provide findings on 3D integration with particular focus on interconnect structures. We suggest consideration of these findings when formulating guidelines for successful 3D-IC design automation.:1 Introduction 1.1 The 3D Integration Approach for Electronic Circuits 1.2 Technologies for 3D Integrated Circuits 1.3 Design Approaches for 3D Integrated Circuits 2 State of the Art in Design Automation for 3D Integrated Circuits 2.1 Thermal Management 2.2 Partitioning and Floorplanning 2.3 Placement and Routing 2.4 Power and Clock Delivery 2.5 Design Challenges 3 Research Objectives 4 Planning Through-Silicon Via Islands for Block-Level Design Reuse 4.1 Problems for Design Reuse in 3D Integrated Circuits 4.2 Connecting Blocks Using Through-Silicon Via Islands 4.2.1 Problem Formulation and Methodology Overview 4.2.2 Net Clustering 4.2.3 Insertion of Through-Silicon Via Islands 4.2.4 Deadspace Insertion and Redistribution 4.3 Experimental Investigation 4.3.1 Wirelength Estimation 4.3.2 Configuration 4.3.3 Results and Discussion 4.4 Summary and Conclusions 5 Planning Through-Silicon Vias for Design Optimization 5.1 Deadspace Requirements for Optimized Planning of Through-Silicon Vias 5.2 Multiobjective Design Optimization of 3D Integrated Circuits 5.2.1 Methodology Overview and Configuration 5.2.2 Techniques for Deadspace Optimization 5.2.3 Design-Quality Analysis 5.2.4 Planning Different Types of Through-Silicon Vias 5.3 Experimental Investigation 5.3.1 Configuration 5.3.2 Results and Discussion 5.4 Summary and Conclusions 6 3D Floorplanning for Structural Planning of Massive Interconnects 6.1 Block Alignment for Interconnects Planning in 3D Integrated Circuits 6.2 Corner Block List Extended for Block Alignment 6.2.1 Alignment Encoding 6.2.2 Layout Generation: Block Placement and Alignment 6.3 3D Floorplanning Methodology 6.3.1 Optimization Criteria and Phases and Related Cost Models 6.3.2 Fast Thermal Analysis 6.3.3 Layout Operations 6.3.4 Adaptive Optimization Schedule 6.4 Experimental Investigation 6.4.1 Configuration 6.4.2 Results and Discussion 6.5 Summary and Conclusions 7 Research Summary, Conclusions, and Outlook Dissertation Theses Notation Glossary BibliographyDreidimensional integrierte Schaltkreise (3D-ICs) beruhen auf neuartigen Herstellungs- und Integrationstechnologien, wobei vor allem “klassische” 2D-ICs vertikal zu einem neuartigen 3D-System gestapelt werden. Dieser Ansatz zur Erschließung der dritten Dimension im Schaltkreisentwurf ist nach Expertenmeinung dazu geeignet, höhere Integrationsdichten zu erreichen, heterogene Integration zu realisieren, kürzere Verdrahtungswege zu ermöglichen, Leistungsaufnahmen zu reduzieren, Datenübertragungsraten zu erhöhen, sowie hoch-parallele Systeme in einer Baugruppe umzusetzen. Aufgrund von technologischen und entwurfsmethodischen Schwierigkeiten bleibt jedoch bisher die kommerzielle Anwendung von 3D-ICs deutlich hinter den Erwartungen zurück. In dieser Arbeit werden drei ausgewählte, praktisch relevante Problemstellungen der Entwurfsautomatisierung von 3D-ICs bearbeitet: (i) die Verbesserung der (eingeschränkten) Wiederverwendbarkeit von zuverlässigen 2D-Intellectual-Property-Blöcken, (ii) die komplexe Planung von verschiedenartigen, verhältnismäßig großen Through-Silicion Vias unter Beachtung ihres Einflusses auf die Entwurfsqualität, und (iii) die strukturelle Einbindung von massiv-parallelen, 3D-IC-spezifischen Verbindungsstrukturen während der Floorplanning-Phase. Das Ziel dieser Arbeit besteht darin, Verbindungsstrukturen mit deren wesentlichen Eigenschaften bereits in den frühen Phasen des Entwurfsprozesses zu berücksichtigen. Dies begünstigt einen qualitativ hochwertigen Entwurf von 3D-ICs. Die in dieser Arbeit vorgestellten modularen Entwurfsprozess-Erweiterungen bzw. -Methodiken dienen zur effizienten Lösung der oben genannten Problemstellungen. Experimentelle Untersuchungen bestätigen die Wirksamkeit sowie die Effektivität der erarbeiten Methoden. Darüber hinaus liefern sie praktische Erkenntnisse bezüglich der Anwendung von 3D-ICs und der Planung deren Verbindungsstrukturen. Diese Erkenntnisse sind zur Ableitung von Richtlinien für den erfolgreichen Entwurf von 3D-ICs dienlich.:1 Introduction 1.1 The 3D Integration Approach for Electronic Circuits 1.2 Technologies for 3D Integrated Circuits 1.3 Design Approaches for 3D Integrated Circuits 2 State of the Art in Design Automation for 3D Integrated Circuits 2.1 Thermal Management 2.2 Partitioning and Floorplanning 2.3 Placement and Routing 2.4 Power and Clock Delivery 2.5 Design Challenges 3 Research Objectives 4 Planning Through-Silicon Via Islands for Block-Level Design Reuse 4.1 Problems for Design Reuse in 3D Integrated Circuits 4.2 Connecting Blocks Using Through-Silicon Via Islands 4.2.1 Problem Formulation and Methodology Overview 4.2.2 Net Clustering 4.2.3 Insertion of Through-Silicon Via Islands 4.2.4 Deadspace Insertion and Redistribution 4.3 Experimental Investigation 4.3.1 Wirelength Estimation 4.3.2 Configuration 4.3.3 Results and Discussion 4.4 Summary and Conclusions 5 Planning Through-Silicon Vias for Design Optimization 5.1 Deadspace Requirements for Optimized Planning of Through-Silicon Vias 5.2 Multiobjective Design Optimization of 3D Integrated Circuits 5.2.1 Methodology Overview and Configuration 5.2.2 Techniques for Deadspace Optimization 5.2.3 Design-Quality Analysis 5.2.4 Planning Different Types of Through-Silicon Vias 5.3 Experimental Investigation 5.3.1 Configuration 5.3.2 Results and Discussion 5.4 Summary and Conclusions 6 3D Floorplanning for Structural Planning of Massive Interconnects 6.1 Block Alignment for Interconnects Planning in 3D Integrated Circuits 6.2 Corner Block List Extended for Block Alignment 6.2.1 Alignment Encoding 6.2.2 Layout Generation: Block Placement and Alignment 6.3 3D Floorplanning Methodology 6.3.1 Optimization Criteria and Phases and Related Cost Models 6.3.2 Fast Thermal Analysis 6.3.3 Layout Operations 6.3.4 Adaptive Optimization Schedule 6.4 Experimental Investigation 6.4.1 Configuration 6.4.2 Results and Discussion 6.5 Summary and Conclusions 7 Research Summary, Conclusions, and Outlook Dissertation Theses Notation Glossary Bibliograph

Network-on-Chip

Addresses the Challenges Associated with System-on-Chip Integration Network-on-Chip: The Next Generation of System-on-Chip Integration examines the current issues restricting chip-on-chip communication efficiency, and explores Network-on-chip (NoC), a promising alternative that equips designers with the capability to produce a scalable, reusable, and high-performance communication backbone by allowing for the integration of a large number of cores on a single system-on-chip (SoC). This book provides a basic overview of topics associated with NoC-based design: communication infrastructure design, communication methodology, evaluation framework, and mapping of applications onto NoC. It details the design and evaluation of different proposed NoC structures, low-power techniques, signal integrity and reliability issues, application mapping, testing, and future trends. Utilizing examples of chips that have been implemented in industry and academia, this text presents the full architectural design of components verified through implementation in industrial CAD tools. It describes NoC research and developments, incorporates theoretical proofs strengthening the analysis procedures, and includes algorithms used in NoC design and synthesis. In addition, it considers other upcoming NoC issues, such as low-power NoC design, signal integrity issues, NoC testing, reconfiguration, synthesis, and 3-D NoC design. This text comprises 12 chapters and covers: The evolution of NoC from SoC—its research and developmental challenges NoC protocols, elaborating flow control, available network topologies, routing mechanisms, fault tolerance, quality-of-service support, and the design of network interfaces The router design strategies followed in NoCs The evaluation mechanism of NoC architectures The application mapping strategies followed in NoCs Low-power design techniques specifically followed in NoCs The signal integrity and reliability issues of NoC The details of NoC testing strategies reported so far The problem of synthesizing application-specific NoCs Reconfigurable NoC design issues Direction of future research and development in the field of NoC Network-on-Chip: The Next Generation of System-on-Chip Integration covers the basic topics, technology, and future trends relevant to NoC-based design, and can be used by engineers, students, and researchers and other industry professionals interested in computer architecture, embedded systems, and parallel/distributed systems