RF MEMS reference oscillators platform for wireless communications

A complete platform for RF MEMS reference oscillator is built to replace bulky quartz from mobile devices, thus reducing size and cost. The design targets LTE transceivers. A low phase noise 76.8 MHz reference oscillator is designed using material temperature compensated AlN-on-silicon resonator. The thesis proposes a system combining piezoelectric resonator with low loading CMOS cross coupled series resonance oscillator to reach state-of-the-art LTE phase noise specifications. The designed resonator is a two port fundamental width extensional mode resonator. The resonator characterized by high unloaded quality factor in vacuum is designed with low temperature coefficient of frequency (TCF) using as compensation material which enhances the TCF from - 3000 ppm to 105 ppm across temperature ranges of -40˚C to 85˚C. By using a series resonant CMOS oscillator, phase noise of -123 dBc/Hz at 1 kHz, and -162 dBc/Hz at 1MHz offset is achieved. The oscillator’s integrated RMS jitter is 106 fs (10 kHz–20 MHz), consuming 850 μA, with startup time is 250μs, achieving a Figure-of-merit (FOM) of 216 dB. Electronic frequency compensation is presented to further enhance the frequency stability of the oscillator. Initial frequency offset of 8000 ppm and temperature drift errors are combined and further addressed electronically. A simple digital compensation circuitry generates a compensation word as an input to 21 bit MASH 1 -1-1 sigma delta modulator incorporated in RF LTE fractional N-PLL for frequency compensation. Temperature is sensed using low power BJT band-gap front end circuitry with 12 bit temperature to digital converter characterized by a resolution of 0.075˚C. The smart temperature sensor consumes only 4.6 μA. 700 MHz band LTE signal proved to have the stringent phase noise and frequency resolution specifications among all LTE bands. For this band, the achieved jitter value is 1.29 ps and the output frequency stability is 0.5 ppm over temperature ranges from -40˚C to 85˚C. The system is built on 32nm CMOS technology using 1.8V IO device

Fiber Optics

Optical fibers in metrology, telecommunications, sensors, manufacturing, and health science have gained massive research interest. The number of applications is increasing at a fast pace. This book aims to present a collection of recent advances in fiber optics, addressing both fundamental and industrial applications. It covers the current progress and latest breakthroughs in emergent applications of fiber optics. The book includes five chapters on recent developments in optical fiber communications and fiber sensors, as well as the design, simulation, and fabrication of novel fiber concepts

New strategies for low noise, agile PLL frequency synthesis

Phase-Locked Loop based frequency synthesis is an essential technique employed in wireless communication systems for local oscillator generation. The ultimate goal in any design of frequency synthesisers is to generate precise and stable output frequencies with fast switching and minimal spurious and phase noise. The conflict between high resolution and fast switching leads to two separate integer synthesisers to satisfy critical system requirements. This thesis concerns a new sigma-delta fractional-N synthesiser design which is able to be directly modulated at high data rates while simultaneously achieving good noise performance. Measured results from a prototype indicate that fast switching, low noise and spurious free spectra are achieved for most covered frequencies. The phase noise of the unmodulated synthesiser was measured −113 dBc/Hz at 100 kHz offset from the carrier. The intermodulation effect in synthesisers is capable of producing a family of spurious components of identical form to fractional spurs caused in quantisation process. This effect directly introduces high spurs on some channels of the synthesiser output. Numerical and analytic results describing this effect are presented and amplitude and distribution of the resulting fractional spurs are predicted and validated against simulated and measured results. Finally an experimental arrangement, based on a phase compensation technique, is presented demonstrating significant suppression of intermodulation-borne spurs. A new technique, pre-distortion noise shaping, is proposed to dramatically reduce the impact of fractional spurs in fractional-N synthesisers. The key innovation is the introduction in the bitstream generation process of carefully-chosen set of components at identical offset frequencies and amplitudes and in anti-phase with the principal fractional spurs. These signals are used to modify the Σ-Δ noise shaping, so that fractional spurs are effectively cancelled. This approach can be highly effective in improving spectral purity and reduction of spurious components caused by the Σ-Δ modulator, quantisation noise, intermodulation effects and any other circuit factors. The spur cancellation is achieved in the digital part of the synthesiser without introducing additional circuitry. This technique has been convincingly demonstrated by simulated and experimental results

Time-encoding analog-to-digital converters : bridging the analog gap to advanced digital CMOS? Part 2: architectures and circuits

The scaling of CMOS technology deep into the nanometer range has created challenges for the design of highperformance analog ICs: they remain large in area and power consumption in spite of process scaling. Analog circuits based on time encoding [1], [2], where the signal information is encoded in the waveform transitions instead of its amplitude, have been developed to overcome these issues. While part one of this overview article [3] presented the basic principles of time encoding, this follow-up article describes and compares the main time-encoding architectures for analog-to-digital converters (ADCs) and discusses the corresponding design challenges of the circuit blocks. The focus is on structures that avoid, as much as possible, the use of traditional analog blocks like operational amplifiers (opamps) or comparators but instead use digital circuitry, ring oscillators, flip-flops, counters, an so on. Our overview of the state of the art will show that these circuits can achieve excellent performance. The obvious benefit of this highly digital approach to realizing analog functionality is that the resulting circuits are small in area and more compatible with CMOS process scaling. The approach also allows for the easy integration of these analog functions in systems on chip operating at "digital" supply voltages as low as 1V and lower. A large part of the design process can also be embedded in a standard digital synthesis flow

Undersampling bandpass modulator architectures

Continuous-time delta sigma modulators -- Undersampling Delta-sigma modulators for radio receivers -- A novel continuous-time delta sigma modulator -- New delta modulator based on undersampling

NONLINEARITY COMPENSATION AND HIGH VOLTAGE PROTECTION OF CURRENT STEERING DAC

Department of Electrical EngineeringCurrent steering digital to analog converter (DAC) always suffer from lots of problem like mismatch errors and timing related dynamic errors. Diverse studies from art-of-the-state suggest methods for compensate some of these errors. Typical examples of compensation methods are segmentation, quad-quadrant (Q2) random walk and dynamic element matching (DEM). These compensation methods reduce lots of fundamental errors while used together with other proposed technique in this thesis. This thesis propose two structure. One structure is related with industrial applications. Industrial application usually requires 10V swing for voltage driving and 20mA swing for current driving. Conventional industrial DAC satisfy these swing requirement with high voltage driving amplifier. But driving amplifier consumes additional power and adds its own distortion to output signal. High voltage protection structure is proposed to satisfy industrial swing requirement and solve the problems of driving amplifier combined DAC. Proposed high voltage protection structure decrease cost of manufacturing by decreasing number of high voltage transistor. Proposed structure also increases linearity by changing effective output impedance and decreases additional current consumption while satisfying industrial swing requirement. The other proposed structure is related with resolution improving. Recent current steering DAC becomes fast enough to cover over GHz range with developing technologies. However resolution is still limited by matching properties. Current steering DAC with resolution improving sigma-delta (?????) modulation is proposed. It increase resolution by noise shaping of ????? modulation while sacrificing speed. It still fast because recent current steering DAC is very fast. ????? modulator only randomize LSB side and shaping LSB related noise. Q2 random walk and DEM are also included to randomize MSB side and reduce MSB related noise. Two version of test chips are tested. 12bit random rotation-based binary-weighted (RRSB) DEM current steering DAC is implemented in 130nm compliment metal-oxide semiconductor (CMOS) process. Test result shows the effect of MSB side randomizing DEM from art-of-the-state. Proposed 14bit resolution improved DAC with high voltage protection is implemented in 180nm bipolar + compliment + double-diffused metal oxide semiconductor (BCDMOS) process. Test result verify performance improvement in frequency domain. Operation voltage and resolution of DAC can be changed by each proposed method. DAC can be applied to various application that require various operation voltage and resolution by using both method properly.ope

Linear Operation of Switch-Mode Outphasing Power Amplifiers

Radio transceivers are playing an increasingly important role in modern society. The ”connected” lifestyle has been enabled by modern wireless communications. The demand that has been placed on current wireless and cellular infrastructure requires increased spectral efficiency however this has come at the cost of power efficiency. This work investigates methods of improving wireless transceiver efficiency by enabling more efficient power amplifier architectures, specifically examining the role of switch-mode power amplifiers in macro cell scenarios. Our research focuses on the mechanisms within outphasing power amplifiers which prevent linear amplification. From the analysis it was clear that high power non-linear effects are correctable with currently available techniques however non-linear effects around the zero crossing point are not. As a result signal processing techniques for suppressing and avoiding non-linear operation in low power regions are explored. A novel method of digital pre-distortion is presented, and conventional techniques for linearisation are adapted for the particular needs of the outphasing power amplifier. More unconventional signal processing techniques are presented to aid linearisation of the outphasing power amplifier, both zero crossing and bandwidth expansion reduction methods are designed to avoid operation in nonlinear regions of the amplifiers. In combination with digital pre-distortion the techniques will improve linearisation efforts on outphasing systems with dynamic range and bandwidth constraints respectively. Our collaboration with NXP provided access to a digital outphasing power amplifier, enabling empirical analysis of non-linear behaviour and comparative analysis of behavioural modelling and linearisation efforts. The collaboration resulted in a bench mark for linear wideband operation of a digital outphasing power amplifier. The complimentary linearisation techniques, bandwidth expansion reduction and zero crossing reduction have been evaluated in both simulated and practical outphasing test benches. Initial results are promising and indicate that the benefits they provide are not limited to the outphasing amplifier architecture alone. Overall this thesis presents innovative analysis of the distortion mechanisms of the outphasing power amplifier, highlighting the sensitivity of the system to environmental effects. Practical and novel linearisation techniques are presented, with a focus on enabling wide band operation for modern communications standards

Interface Circuits for Microsensor Integrated Systems

ca. 200 words; this text will present the book in all promotional forms (e.g. flyers). Please describe the book in straightforward and consumer-friendly terms. [Recent advances in sensing technologies, especially those for Microsensor Integrated Systems, have led to several new commercial applications. Among these, low voltage and low power circuit architectures have gained growing attention, being suitable for portable long battery life devices. The aim is to improve the performances of actual interface circuits and systems, both in terms of voltage mode and current mode, in order to overcome the potential problems due to technology scaling and different technology integrations. Related problems, especially those concerning parasitics, lead to a severe interface design attention, especially concerning the analog front-end and novel and smart architecture must be explored and tested, both at simulation and prototype level. Moreover, the growing demand for autonomous systems gets even harder the interface design due to the need of energy-aware cost-effective circuit interfaces integrating, where possible, energy harvesting solutions. The objective of this Special Issue is to explore the potential solutions to overcome actual limitations in sensor interface circuits and systems, especially those for low voltage and low power Microsensor Integrated Systems. The present Special Issue aims to present and highlight the advances and the latest novel and emergent results on this topic, showing best practices, implementations and applications. The Guest Editors invite to submit original research contributions dealing with sensor interfacing related to this specific topic. Additionally, application oriented and review papers are encouraged.

Signal processing using short word-length

Recently short word-length (normally 1 bit or bits) processing has become a promising technique. However, there are unresolved issues in sigma-delta modulation, which is the basis for 1b/2b systems. These issues hindered the full adoption of single-bit techniues in industry. Among these problems is the stability of high-order modulators and the limit cycle behaviour. More importantly, there is no adaptive LMS structure of any kind in 1b/2b domain. The challenge in this problem is the harsh quantization that prevents straightforward LMS application. In this thesis, the focus has been made on three axes: designing new single-bit DSP applications, proposing novel approaches for stability analysis, and tacking the unresolved problems of 1b/2b adaptive filtering. Two structures for 1b digital comb filtering are proposed. A ternary DC blocker structure is also presented and performanc e is tested. We also proposed a single-bit multiplierless DC-blocking structure. The stability of a single-bit high-order signma-delta modulator is studied under dc inputs. A new approach for stability analysis is proposed based on analogy with PLL analysis. Finally we succeeded in designing 1b/2b Wiener-like filtering and introduced (for the first time) three 1b/2b adaptive schemes